HBM MP85ADP-PN-S Manuals

Manuals and User Guides for HBM MP85ADP-PN-S. We have 1 HBM MP85ADP-PN-S manual available for free PDF download: Operating Manual

HBM MP85ADP-PN-S Operating Manual (160 pages)

Brand: HBM | Category: Switch | Size: 2.57 MB

Table of Contents
3
Safety Instructions
8
Markings Used
12
Markings Used in this Document
12
Symbols on the Device
12
Introduction
14
About this Documentation
14
Scope of Supply
14
Accessories
15
General
16
Installing/Removing the MP85A (Schematic Diagrams)
18
Mechanical Installation/Removal
18
Connecting Several Devices
20
Electrical Connection
21
General Notes on Connection
21
Overview of MP85A(-S) Functions
22
Overview of MP85ADP(-S)/MP85ADP-PN(-S) Functions
23
Supply Voltage and Control Inputs/Outputs
24
Connecting the Power Supply
25
External Supply Voltage for Control Outputs
25
Reference Potential for Control Inputs/Switch Test Inputs
26
Transducer
27
Synchronization of Carrier Frequencies
27
Strain Gage and Displacement Transducers, Potentiometric and LVDT Sensors
27
Incremental, SSI and DC Sensors
31
Piezoelectric Measurement Chains
33
TEDS (Transducer Electronic Data Sheet) Chips
37
TEDS Connection
37
Parameterization with TEDS
38
Interfaces
40
Ethernet Interface
40
CAN Interface
42
PROFIBUS Interface (MP85ADP/MP85ADP-S Only)
43
Profinet Interface (MP85ADP-PN/MP85ADP-PN-S Only)
45
Switch Settings/Replacing the Battery
47
Changing the Supply Voltage for Active Sensors
47
Replacing the Battery
48
CAN Termination Resistor
49
Starting Up/Setup Mode
50
Operation
52
Device Settings, Measured Values, Process Status, PROFIBUS
52
Memory Card, Error Types, Firmware Update, Device Backup
52
Overview of All Groups and Parameters
59
Setting Parameters on the Device
61
Hardware Setup
62
Power Supply/Transducers
62
Connection Via Ethernet
63
Connecting the CAN Adapter (USB)
63
Installing the PME Assistant Software
64
Using the PME Assistant
65
Using the Ethernet Interface
66
Using the USB Interface
66
Automatic Version Detection
68
Firmware Updates
68
Offline Mode
70
Measurement Procedure
71
Data Reduction
71
Classification
74
Limit Monitoring in Real Time
75
Hiding External Tolerances
75
Evaluation Criteria
77
Measurement Programs (Parameter Sets)
82
Switch Test (Easyswitch)
85
Switch Test
85
Haptic Test
88
Communication with a Control System
90
MP85A Process Controller in the Machine Control System
90
Test Process Sequence over Time
93
Transducer Test
95
Zero Balance
96
Simulation of Digital Outputs
97
Parameter Sets (Measurement Programs)
97
Evaluation/Backup Process Times
100
Process Data Backup/Production Data Management
103
Display and Control Options
105
Fastpress Suite Software
105
Error Messages/Operating State (LED Display)
107
Faqs: Frequently Asked Questions (MP85A and PME Assistant)
113
How Do I Set the Interface on the MP85A
113
How Do I Set an IP Address on My PC
115
How Do I Connect the PME Assistant to the MP85A
116
How Can I Find the File System on My PC, and Which Should I Use
117
When I Launch the PME Assistant, What Do the Options Do
118
What Happens if I Connect Via an Existing Ethernet Connection
119
What Are the Requirements for an MMC/SD Card
120
What Is the Relationship between the Data Rate and the Filter Settings
120
What Does Data Reduction Do and How Do I Set It
121
What Options Are There for Starting, Stopping and Ending Measurement
124
How Do I Work in Setup Mode
133
How Long Does Zero Balance Take and What Does It Involve
134
What Takes Place During a Transducer Test and What Are the Important Points
134
What Are the Limitations for (Transducer) Scaling
135
What Must I Bear in Mind When Switching Parameter Sets
135
How Can I Find Out/Track Changes to Device Settings
136
What Error Messages Are There for Measurement/The Process Status, and How Can I Correct Errors
137
What Do the Error Messages for Tolerance Window Violations Mean
139
What Do the Leds on the MP85A Mean
141
What Do I Have to Look out for When Saving Process Data (Curves/Results)
144
What Does the Flow Diagram of a Process-Optimized Measurement Look Like
145
What Does the Flow Diagram of a Measurement with no Data Loss Look Like
146
What Causes a Digital Output to be Set
146
How Can I Generate a Log Printout of a Process
147
How Can I Transfer All the Settings of One MP85A to Another Device (Cloning)
147
How Do I Do a Firmware Update, and Can It be Prevented
148
Downloading the Firmware Update
148
Procedure for Updating the Firmware
149
What Does a Tolerance Band Look Like
150
What Does an Envelope Curve Look Like
150
What Is TEDS
150
Software and Firmware Updates
152
Waste Disposal and Environmental Protection
154
Technical Support
155
Index
156

HBM Categories

Transducer Measuring Instruments Accessories Amplifier Industrial Equipment

More HBM Manuals

HBM MP85ADP-PN-S Manuals

HBM MP85ADP-PN-S Operating Manual (160 pages)

Table of Contents

Related Products

HBM Categories