Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
Colour CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
Mount Embedded type
VCC-9000EBCP/EBSP
VCC-9100EBCP/EBSP
About this manual
• Before installing and using this unit, please read this manual carefully.
Be sure to keep it handy for later reference.
• This manual gives basic connections and operating instructions for 12 PAL models.
Indoor type
VCC-9000INCP/INSP
VCC-9100INCP/INSP
VCC-9000EBCP/EBSP
VCC-9000INCP/INSP
VCC-9000EXCP/EXSP
VCC-9100EBCP/EBSP
VCC-9100INCP/INSP
VCC-9100EXCP/EXSP
English
Deutsch
Francais
Outdoor type
VCC-9000EXCP/EXSP
VCC-9100EXCP/EXSP
GB
D
F
CS
Advertisement
Table of Contents
Related Manuals for Sanyo VCC-9000EBCP/EBSP
Summary of Contents for Sanyo VCC-9000EBCP/EBSP
- Page 1 VCC-9000EBCP/EBSP INSTRUCTION MANUAL VCC-9000INCP/INSP BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS VCC-9000EXCP/EXSP VCC-9100EBCP/EBSP VCC-9100INCP/INSP VCC-9100EXCP/EXSP English Colour CCD camera Deutsch CCD-Farbkamera Francais Caméra CCD COULEUR Mount Embedded type Indoor type Outdoor type VCC-9000EBCP/EBSP VCC-9000INCP/INSP VCC-9000EXCP/EXSP VCC-9100EBCP/EBSP VCC-9100INCP/INSP VCC-9100EXCP/EXSP About this manual • Before installing and using this unit, please read this manual carefully.
-
Page 2: Table Of Contents
PART NAMES • SETTINGS • SETUP1 and automatic backlight compensation functions operate so (VCC-9000EBCP/EBSP, 9100EBCP/EBSP)... 3 that clear images are transmitted at all times. PART NAMES • SETTINGS • SETUP2 •... -
Page 3: Precautions
Clamp fitting ........1 consult your dealer or an Authorized Sanyo Service Center. -
Page 4: Part Names • Settings • Setup1 (Vcc-9000Ebcp/Ebsp, 9100Ebcp/Ebsp)
VCC-9000EBCP/EBSP, VCC-9100EBCP/EBSP PART NAMES • SETTINGS • SETUP1 Part Names VCC-9000EBCP/EBSP, 9100EBCP/EBSP (Mount Embedded type) Camera connection cable Power indicator Connection board Camera connection cable Connect the communication cable and the power supply This is used to connect the connection board inside the cable to the connectors on this board. - Page 5 Termination setting (JP3) camera. The termination connection setting must be made if this The default setting is the “SANYO” protocol (all OFF). camera is connected to a network system and it is in the List of Protocol Settings termination connection position.
- Page 6 VCC-9000EBCP/EBSP, VCC-9100EBCP/EBSP PART NAMES • SETTINGS • SETUP1 Setup Refer to page 45 for details on how to drill the ceiling installation holes. Install the main cover to the ceiling. NOTE: • You can also connect the cables before embedding the Make a hole in the ceiling for inserting the main cover.
-
Page 7: Part Names • Settings • Setup2 (Vcc-9000Incp/Insp, 9100Incp/Insp)
VCC-9000INCP/INSP, VCC-9100INCP/INSP PART NAMES • SETTINGS • SETUP2 Part Names VCC-9000INCP/INSP, 9100INCP/INSP (Indoor type) Camera connection cable Power indicator Connection board Camera connection cable Connect the communication cable and the power supply This is used to connect the connection board inside the cable to the connectors on this board. -
Page 8: Connect The Cables
VCC-9000INCP/INSP, VCC-9100INCP/INSP PART NAMES • SETTINGS • SETUP2 Setup Install the bracket. Installation to a wall Installation to a ceiling While aligning the bracket base with the setup Loosen the anchor bolts of the bracket base, and position, make four marks on the wall at the mounting then turn the bracket base to remove it. - Page 9 VCC-9000INCP/INSP, VCC-9100INCP/INSP PART NAMES • SETTINGS • SETUP2 Install the main cover to the bracket. Connect the dome cover with the wire. Place the connection ring of drop-prevention wire When installing to a wall the dome cover onto the connection screw of the main Wind the accessory waterproof sealing tape around cover, and then secure it by tightening the two nuts.
-
Page 10: Part Names • Settings • Setup3 (Vcc-9000Excp/Exsp, 9100Excp/Exsp)
VCC-9000EXCP/EXSP, VCC-9100EXCP/EXSP PART NAMES • SETTINGS • SETUP3 Part Names VCC-9000EXCP/EXSP, 9100EXCP/EXSP (Outdoor type) Camera connection cable Power indicator Connection board Camera connection cable Connect the communication cable and the power supply This is used to connect the connection board inside the cable to the connectors on this board. - Page 11 VCC-9000EXCP/EXSP, VCC-9100EXCP/EXSP PART NAMES • SETTINGS • SETUP3 Setup Install the bracket. Installation to a wall Installation to a ceiling While aligning the bracket base with the setup Loosen the anchor bolts of the bracket base, and position, make four marks on the wall at the mounting then turn the bracket base to remove it.
- Page 12 VCC-9000EXCP/EXSP, VCC-9100EXCP/EXSP PART NAMES • SETTINGS • SETUP3 Install the main cover to the bracket. Connect the dome cover with the wire. Place the connection ring of drop-prevention wire When installing to a wall the dome cover onto the connection screw of the main Wind the accessory waterproof sealing tape around cover, and then secure it by tightening the two nuts.
-
Page 13: Connections
CONNECTIONS Turn off the power for all equipment before making these connections. Read the instruction manuals for all of the equipment being connected. In addition, if the cables are connected incorrectly, it may cause smoke or incorrect operation to occur. Connections for using RS-485 control Power cable (24 V AC, 50 Hz) - Page 14 CONNECTIONS Connections for using coaxial control System connections (1) Power supply Power supply 1 – 16 Video output Video output connector (BNC) connector (BNC) Multiplexer (sold separately) TV monitor (sold separately) RS-485 connector System controller (sold separately) ALARM IN connector Ground (C) Digital video recorder Ground (C)
-
Page 15: Operation
C M : 0 0 1 5 : 3 0 : 3 0 MODE INDIVIDUAL (Menu display) CAMERA S/N:3730116601 CAMERA ID:000 BAUD RATE:19200BPS PROTOCOL :SANYO MODEL :VCC-9000P VERSION :3.14A ·SYSTEM INFORMATION LENS CAMERA PAN/TILT PARAMETERS AUTO MODE PRIVACY MASK ·END (Model: VSP-8000) Connect all equipment and turn on the power. -
Page 16: Menu Explanations
MENU EXPLANATIONS SYSTEM SETTINGS (SYSTEM INFORMATION) (See p16) The menu settings are divided into six sub-menus. A Camera ID settings and title settings CAMERA INFORMATION (CAMERA INFORMATION) DISPLAY CONFIGURATION PASSWORD CHANGE B Screen display settings (DISPLAY FACTORY DEFAULT RESET CONFIGURATION) ·BACK C Changing the password (PASSWORD CHANGE) -
Page 17: System Settings
SYSTEM SETTINGS ·SYSTEM INFORMATION ·CAMERA INFORMATION LENS DISPLAY CONFIGURATION CAMERA PASSWORD CHANGE PAN/TILT PARAMETERS FACTORY DEFAULT AUTO MODE RESET PRIVACY MASK BACK A Camera ID settings and title D Restoring camera settings to settings their default settings (CAMERA INFORMATION) (FACTORY DEFAULT) (See p20) (See p17) The camera settings can be returned to the default settings. -
Page 18: (Camera Information)
SYSTEM SETTINGS A Camera ID settings and title Select “BACK”, and then tilt the joystick lever to c. settings The “CAMERA ID” setting will flash. (CAMERA INFORMATION) CAMERA ID : 001 TITLE:0000000000000000 BACK Changing the address Change the “CAMERA ID” setting. Refer to “LIST OF ADDRESS SETTINGS (SW1)”... -
Page 19: B Screen Display Settings
SYSTEM SETTINGS B Screen display settings Setting menu screens (DISPLAY CONFIGURATION) CAMERA TITLE (See p17) Select “DISPLAY CONFIGURATION”, and Shows the camera title. then tilt the joystick lever to c. CAMERA ID : 001 ·TITLE:0000000000000000 BACK The screen display setting screen will be displayed. AUTO PAN No. -
Page 20: Changing The Password (Password Change)
SYSTEM SETTINGS C Changing the password (PASSWORD CHANGE) Changing the password Setting and deactivating a password If changing the password from “123456” (default setting) to To set a password, set “PASSWORD LOCK” to “ON”. “654321” Select “PASSWORD CHANGE”, and then Select “PASSWORD CHANGE”, and then tilt the joystick lever to c. -
Page 21: D Restoring Camera Settings To Their Default Settings
SYSTEM SETTINGS D Restoring camera settings to List of Default Setting Values Menu item Setting Menu item Setting their default settings CAMERA TITLE WHITE BALANCE (FACTORY DEFAULT) AUTO PAN No. MWB-R The camera settings can be returned to the default settings. PRESET TITLE MWB-B TOUR No. -
Page 22: Lens Settings
LENS SETTINGS SYSTEM INFORMATION ·ZOOM SPEED :HIGH ·LENS EL ZOOM :OFF CAMERA JOYSTICK AUTO :BOTH PAN/TILT PARAMETERS AUTO FOCUS :005 AUTO MODE AUTO IRIS :005 PRIVACY MASK IRIS LEVEL :040 DAY/NIGHT :AUTO BACK A Zoom speed settings E Automatic iris restore time (ZOOM SPEED)(See p22) setting (AUTO IRIS)(See p23) The following zoom speeds can be selected for the lens. -
Page 23: A Zoom Speed Settings (Zoom Speed)
LENS SETTINGS A Zoom speed settings B Electronic zoom maximum ratio (ZOOM SPEED) settings (EL ZOOM) Press the MENU button. Select “EL ZOOM”, and then tilt the joystick lever to c. SYSTEM INFORMATION The “EL ZOOM” setting will flash. MENU ·LENS CAMERA PAN/TILT PARAMETERS... -
Page 24: D Automatic Focus Restore Time Settings
LENS SETTINGS D Automatic focus restore time E Automatic iris restore time settings (AUTO FOCUS) setting (AUTO IRIS) Select “AUTO FOCUS”, and then tilt the Select “AUTO IRIS”, and then tilt the joystick lever to c. joystick lever to c. The “AUTO FOCUS”... -
Page 25: F Iris Level Settings (Iris Level)
LENS SETTINGS F Iris level settings (IRIS LEVEL) G Day/Night settings (DAY/NIGHT) (VCC-9100P series only) Select “IRIS LEVEL”, and then tilt the joystick lever to c. Select “DAY/NIGHT”, and then tilt the The “IRIS LEVEL” setting will flash. joystick lever to c. The “DAY/NIGHT”... -
Page 26: Camera Settings
CAMERA SETTINGS SYSTEM INFORMATION ·SENSE UP :OFF LENS SHUTTER :OFF ·CAMERA WHITE BALANCE :ATW PAN/TILT PARAMETERS :OFF AUTO MODE BACK PRIVACY MASK A Sensitivity increase settings C White balance settings (SENSE UP)(See p26) (WHITE BALANCE) (See p26) This sets the amount of increase in electronic sensitivity. If White balance adjustment can be carried out in the following the objects become darker, the CCD exposure time for the two ways: automatic white balance (automatic tracing... -
Page 27: A Sensitivity Increase Settings (Sense Up)
CAMERA SETTINGS A Sensitivity increase settings C White balance settings (SENSE UP) (WHITE BALANCE) Press the MENU button. Setting automatic tracing white balance (ATW) SYSTEM INFORMATION MENU LENS ·CAMERA PAN/TILT PARAMETERS Select “WHITE BALANCE”, and then tilt the AUTO MODE PRIVACY MASK joystick lever to c. -
Page 28: D Backlight Compensation Settings (Blc)
CAMERA SETTINGS D Backlight compensation settings (BLC) Select “BLC”, and then tilt the joystick lever to c. The “BLC” setting will flash. SENSE UP :OFF SHUTTER :OFF WHITE BALANCE :ATW ·BLC :OFF BACK Tilt the joystick lever to j or l to select the compensation setting, and then tilt it to Available settings: ON, OFF Select “BACK”, and then tilt the joystick... -
Page 29: Pan And Tilt Settings
PAN AND TILT SETTINGS Pan and tilt settings control how the camera moves when it is operated directly by using the joystick lever. SYSTEM INFORMATION ·AUTO STOP IDLE :020 LENS PROPORTIONAL PAN:ON CAMERA SET NORTH ·PAN/TILT PARAMETERS BACK AUTO MODE PRIVACY MASK A Settings using joystick C Lens starting point position... -
Page 30: A Settings Using Joystick Operations
PAN AND TILT SETTINGS A Settings using joystick B Panning speed settings for operations (AUTO STOP IDLE) different zoom rations (PROPORTIONAL PAN) Press the MENU button. Select “PROPORTIONAL PAN”, and then SYSTEM INFORMATION tilt the joystick lever to c. MENU LENS CAMERA The “PROPORTIONAL PAN”... -
Page 31: C Lens Starting Point Position Setting
PAN AND TILT SETTINGS C Lens starting point position Direction screen display setting (SET NORTH) When “DIRECTION” in the “DISPLAY CONFIGURATION” This stores the starting point for the direction of the camera system setting is set to “ON”, the direction and angle of the lens, so that when the power is turned on, the camera moves camera lens will be displayed. -
Page 32: Automatic Mode Settings
AUTOMATIC MODE SETTINGS Five automatic mode settings are available. Read the descriptions of each type of setting carefully to select the method that best suits the setup conditions for the camera. SYSTEM INFORMATION PRESET POSITION LENS SEQUENCE CAMERA TOUR PAN/TILT PARAMETERS AUTO PAN ·AUTO MODE SET ZONE... - Page 33 AUTOMATIC MODE SETTINGS C Tour mode settings (TOUR) D Automatic pan settings (See p36) (AUTO PAN)(See p37) This is recommended for use when certain operations This is recommended for use when monitoring a set area are repeated over and over. at a constant speed.
- Page 34 AUTOMATIC MODE SETTINGS E Zone settings (SET ZONE) F Automatic restore standby time (See p38) settings (FUNCTION IDLE) (See p39) This is recommended for use when the area being monitored is split up into several zones. After the camera has been operated manually, if the period of The area being monitored is split up into different zones (up time that has been set using the “FUNCTION IDLE”...
-
Page 35: A Preset Position Settings (Preset Position)
AUTOMATIC MODE SETTINGS NOTE: When the various automatic modes are being controlled from the system controller, the settings for the number that is currently displayed in the menu settings will be carried out. A Preset position settings Setting a preset position (PRESET POSITION) Select “SETTING”, and then tilt the joystick lever to c. -
Page 36: B Sequential Mode Settings (Sequence)
AUTOMATIC MODE SETTINGS B Sequential mode settings Move the joystick lever vertically and horizontally until a setting item flashes, and then tilt the (SEQUENCE) joystick lever to j or l to change the number. To edit the second and subsequent lines, tilt the NOTE: Note that even if you have used EDIT to change the joystick lever to d to display the cursor, and then tilt it pause time for individual preset position, if you... -
Page 37: C Tour Mode Settings (Tour)
AUTOMATIC MODE SETTINGS C Tour mode settings (TOUR) Checking and starting a tour mode Setting a new tour mode Select “TOUR”, and then tilt the joystick Select “TOUR”, and then tilt the joystick lever to c. lever to c. The tour mode setting screen will be displayed. The tour setting screen will be displayed. -
Page 38: D Automatic Pan Settings (Auto Pan)
AUTOMATIC MODE SETTINGS D Automatic pan settings Setting the automatic panning speed (AUTO PAN) Select “PAN SPEED”, and then tilt the joystick lever to c. Setting a new automatic panning mode The “PAN SPEED” setting will flash. Select “AUTO PAN”, and then tilt the Tilt the joystick lever to j or l to select the panning speed, and then tilt it to d. -
Page 39: E Zone Settings (Set Zone)
AUTOMATIC MODE SETTINGS E Zone settings (SET ZONE) The “CALL PRESET 1 TO CONFIRM ..” screen will be displayed. Select “SET ZONE”, and then tilt the joystick lever to c. ZONE TITLE: 0000000000000000 SET LEFT LIMIT The zone setting screen will be displayed. ·SET RIGHT LIMIT DELETE DEFAULT SPEED :... -
Page 40: F Automatic Restore Standby Time Settings
AUTOMATIC MODE SETTINGS F Automatic restore standby time Deleting zone settings settings (FUNCTION IDLE) Select “SET ZONE”, and then tilt the Select “FUNCTION IDLE”, and then tilt the joystick lever to c. joystick lever to c. The zone setting screen will be displayed. The “FUNCTION IDLE”... -
Page 41: Masking Settings (Privacy Mask)
MASKING SETTINGS (PRIVACY MASK) Sometimes there are parts of images being monitored that need to be hidden for privacy reasons. You can apply a privacy mask (gray pattern) to such places to hide them so that the masked areas cannot be seen by people who are not meant to see them. - Page 42 MASKING SETTINGS (PRIVACY MASK) Press the MENU button. Use the joystick lever to adjust the size of the mask, press the “1” numeric button, The main menu screen will be displayed. and then press the ENTER button. SYSTEM INFORMATION “SIZE” will be displayed on the screen. MENU LENS CAMERA...
-
Page 43: List Of Address Settings (Sw1)
LIST OF ADDRESS SETTINGS (SW1) Switch No. Switch No. Switch No. Address Address Address (Camera No.) (Camera No.) (Camera No.) m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m m... -
Page 44: Specifications
Communication format Coaxial control, RS-485 control (Communication terminal: on connection board) Operating environment VCC-9000EBCP/EBSP, 9100EBCP/EBSP, VCC-9000INCP/INSP, 9100INCP/INSP: Temperature: 0° – +40°C, Humidity: 90% R.H. or lower VCC-9000EXCP/EXSP, 9100EXCP/EXSP: Temperature: –20° – +50°C, Humidity: 90% R.H. or lower (maintained by heater and blower) Power supply 24 V AC ±10%, 50 Hz (Power supply terminal: on connection board) - Page 45 SPECIFICATIONS Model Configurations Model name Camera unit + Housing + Dome cover VCC-9000EBCP VCC-MC301P (1) + VA-40ME (3) + VA-CM1C (6) VCC-9000EBSP VCC-MC301P (1) + VA-40ME (3) + VA-CM1S (7) VCC-9100EBCP VCC-MC401P (2) + VA-40ME (3) + VA-CM1C (3) VCC-9100EBSP VCC-MC401P (2) + VA-40ME (3) + VA-CM1S (7) VCC-9000INCP VCC-MC301P (1) + VA-40IN (4) + VA-CM2C (8)
- Page 46 SPECIFICATIONS Making a hole for mount embedded type If installing the mount embedded type (VCC-9000EBCP/EBSP, VCC-9100EBCP/EBSP), mark the installation position on the ceiling by the following procedure, and then drill a hole with a diameter of approximately 225 mm. Setup conditions: •...
- Page 47 SPECIFICATIONS Dimensions VCC-9000EBCP/EBSP VCC-9000INCP/INSP VCC-9000EXCP/EXSP VCC-9100EBCP/EBSP VCC-9100INCP/INSP VCC-9100EXCP/EXSP φ194 φ240 φ218 φ247 (Pendant Mount) (Wall Mount) φ7 R42.5 φ120 φ62 φ218 Appearance and specifications are subject to change for improvement without notice. - 46 - English...
- Page 49 Printed on recycled paper Gedruckt auf recyceltem PapierImprimé sur du papier recyclé SANYO Electric Co., Ltd. Printed in China 1AC6P1P2783-- L5AP4/XE (0305KP-SAE)