Download Print this page
Hide thumbs Also See for VCC-9500:

Advertisement

INSTALLATION MANUAL
Color CCD Camera
Install these units securely according to this installation
manual. Be aware that allowing them to fall may cause
personal injury.
This installation should be made by a qualified service
person and should conform to all local codes.
Please read this manual before installing and using this unit, and always follow the instructions in it for proper
use. Please also read the separate Instruction Manual before using the unit for proper use.
Remove the plastic cover (A) and then the
tape (B) fixing the lens.
Put back the plastic cover (A), and turn it
clockwise until you hear it click to securely
lock it.
Product Lineup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-ceiling Mount (Closed Type) . . . . . . . . . . . . . . . . . . 3
In-ceiling Mount (Open Type) . . . . . . . . . . . . . . . . . . . . 4
Connections and Settings . . . . . . . . . . . . . . . . . . . . . . 5
Address Settings Table . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Be careful when opening holes for installing the unit.
Work with the power and video cables pulled out for
easy installation.
• Make sure to properly perform waterproofing for the
ceiling where you are installing the unit.
• Make sure that the surface in the installation location
has no unevenness and is strong enough to bear the
total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -10°C/+14°F and
+50°C/+122°F (no condensation allowed).
CAUTION: For VA-80S (Power Borard Unit)
ALL-POLE MAINS SWITCH with a contact separation of
at least 3mm in each pole shall be incorporated in the
electrical installation of the building.
Before Installing the Unit
Contents
Important
(A)
(B)

Advertisement

loading

Summary of Contents for Sanyo VCC-9500

  • Page 1: Table Of Contents

    INSTALLATION MANUAL Color CCD Camera Install these units securely according to this installation manual. Be aware that allowing them to fall may cause personal injury. This installation should be made by a qualified service person and should conform to all local codes. Please read this manual before installing and using this unit, and always follow the instructions in it for proper use.
  • Page 2: Product Lineup

    Product Lineup To install the camera unit, the optional housing is required. When using a housing, be sure to choose the correct one for your environment of use. Indoor Type Outdoor Type (Surface Mount) (In-ceiling Mount) ☞P3 ☞P4 ☞P2 ☞ Refer to the instruction ☞...
  • Page 3: Surface Mount

    Surface Mount VA-80F Make sure to also consult the Surface Cover Instruction Manual. 1. Installing the power board unit Place the pattern sheet at the end of this manual on the ceiling, mark the locations and drill the holes for the cables and screws.
  • Page 4: In-Ceiling Mount (Closed Type)

    Align the arrows (C) of the same color (blue) on the camera unit and the inner side of the bracket, and push the camera unit until they click. Align the SANYO logos on the supplied bracket cover and the bracket, and push the cover until they click.
  • Page 5: In-Ceiling Mount (Open Type)

    (B) of the same color on the camera unit, and then push the camera unit until they click. À Align the SANYO logos on the supplied bracket cover and the bracket, and push the cover until they click. ■ How to attach the drop-prevention cable...
  • Page 6: Connections And Settings

    Set the protocol for controlling the camera. ✱ Switch Alarm output OUT 1/2 SSP (SANYO) signal To COM PELCO Termination (Switch 5) ✱ All connection cables should be 24 AWG or higher with a “OFF” is set by default.
  • Page 7 Connections and Settings ■ To prevent electromagnetic interference Be sure to attach the clamping cores supplied with the camera unit to the cables as illustrated. Power cable Control and alarm input/output cables Video cable ■ Connections for using coaxial control (System connection) (1 - 16) Video input Video input...
  • Page 8: Address Settings Table

    Address Settings Table Addresses are specified by setting the switches to ON/OFF. In the table, the circle mark “m” means ON. Set switches as shown in the table. SANYO protocol: 1 - 127 PELCO protocol: 1 - 255 Switch 8 •...
  • Page 9: Pattern Sheet (Inserted At The End Of This Manual)

    Pattern Sheet 4- φ4.5 (0.2) P. D φ168 (6.6) 166 (6.5) Scale: 1/1 Unit: mm (inch)
  • Page 11 MEMO ..............................................................................................................................................................................................................................................................................................
  • Page 12 Dimensions φ 136 (5.4) Unit: mm (inch) Printed on recycled paper Imprimé sur du papier recyclé Impreso en papel reciclado Gedruckt auf Recyclingpapier 使用再生纸印刷 SANYO Electric Co., Ltd. 1AC6P1P3149-A L5BU2/XE (0807KP-HS) Printed in China...

This manual is also suitable for:

Vcc-9600Vcc-9700Vcc-9800p