Cleaning And Sanitizing; Cleaning Solutions; Sanitizing Solutions - lancer Flavor Select 30 Installation And Service Manual

Flavor Select (FS) 22 Ice Beverage Dispenser
2. CLEANING AND SANITIZING INSTRUCTIONS
GENERAL INFORMATION
A. The cleaning and sanitizing procedures provided pertain to the Lancer equipment
identified by this manual. If other equipment is being cleaned, follow the guide
lines established by the manufacturer for that equipment.
B. Lancer equipment (new or reconditioned) is shipped from the factory cleaned and
sanitized in accordance with NSF guidelines. The equipment must be cleaned
and sanitized after installation is complete. The operator of the equipment
must provide continuous maintenance as required by this manual and state and
local health department guidelines to ensure proper operation and sanitation
requirements are maintained.
C. Cleaning and sanitizing should be accomplished only by trained personnel.
Sanitary gloves are to be used during cleaning and sanitizing operations.
Applicable safety precautions must be observed. Instruction warnings on the
product being used must be followed.
D. Other Required Supplies: 1) Clean cloth towels, 2) bucket, 3) extra nozzle, 4)
sanitary gloves and 5) Small brush (PN 22-0017 included with installation kit).
2.1 CLEANING SOLUTION
Mix a mild, non-abrasive detergent (e.g. Sodium Laureth Sulfate, dish soap) with clean, potable
water at a temperature of 90 to 110°F (32 to 43°C). The mixture ratio is one ounce of cleaner to
two gallons of water. Prepare a minimum of five gallons of cleaning solution. Do not use abrasive
cleaners or solvents because they can cause permanent damage to the unit. Ensure rinsing is
thorough, using clean, potable water at a temperature of 90 to 110°F (32 to 43°C).. Extended
lengths of product lines may require additional cleaning solution.
2.2 SANITIZING SOLUTION
Prepare sanitizing solutions in accordance with the manufacturer's written recommendations and
safety guidelines. The solution must provide 50 to 100 parts per million (PPM) chlorine (e.g.
Sodium Hypochlorite or bleach). A minimum of five (5) gallons of sanitizing solution should be
prepared. Any sanitizing solution may be used as long as it is prepared in accordance with the
manufacturer's written recommendations and safety guidelines, and provides 50 to 100 parts per
million (PPM) chlorine.
! WARNING
IF A POWDER SANITIZER IS USED, DISSOLVE IT THOROUGHLY WITH HOT WATER PRIOR TO ADDING TO THE
SYRUP SYSTEM. ENSURE SANITIZING SOLUTION IS REMOVED FROM THE DISPENSER AS INSTRUCTED. AVOID GETTING
SANITIZING SOLUTION ON CIRCUIT BOARDS. DO NOT USE STRONG BLEACHES OR DETERGENTS; THESE CAN DISCOLOR
AND CORRODE VARIOUS MATERIALS. DO NOT USE METAL SCRAPERS, SHARP OBJECTS, STEEL WOOL, SCOURING PADS,
ABRASIVES, OR SOLVENTS ON THE DISPENSER. DO NOT USE HOT WATER ABOVE 140° F (60° C). THIS CAN DAMAGE THE
DISPENSER.
! ADVERTENCIA
SI SE USA UN HIGIENIZADOR EN POLVO, DISUÉLVALO BIEN EN AGUA ANTES DE AGREGARLO AL
SISTEMA DE CONCENTRADO. EL USO DE AGUA CALIENTE CONTRIBUYE A DISOLVER LOS HIGIENIZADORES EN POLVO.
ASEGÚRESE DE HABER ELIMINADO LA SOLUCIÓN DE ESTERILIZACIÓN DEL DISPENSADOR DE ACUERDO CON LAS IN-
STRUCCIONES. LOS RESIDUOS DE LA SOLUCIÓN DE ESTERILIZACIÓN REPRESENTAN UN PELIGRO PARA LA SALUD. EVITE
QUE LA SOLUCIÓN DE ESTERILIZACIÓN LLEGUE A LAS PLACAS DE CIRCUITOS. NO USE LAVANDINAS
NI DETERGENTES QUE PODRÍAN QUITAR EL COLOR Y CORROER DISTINTOS MATERIALES. NO USE RASPADORES
METÁLICOS, OBJETOS FILOSOS, LANA DE ACERO, ESTROPAJOS, ABRASIVOS NI SOLVENTES EN EL DISPENSADOR.
NO USE AGUA CALIENTE A MÁS DE 140 ºF (60 ºC). PODRÍA DAÑAR EL DISPENSADOR.
! AVERTISSEMENT
AVANT L'INJECTION DANS LE SYSTÈME, IL FAUDRA QUE LA POUDRE SEPTIQUE SOIT DISSOLUE
ENTIÈREMENT DANS CHAUDE. L'EAU CHAUDE PERMETTRA UN MEILLEUR PROCÈS DE DISSOLUTION. SUIVANT LES
INSTRUCTIONS JOINTES, IL EST IMPÉRATIF QUE LA SOLUTION SEPTIQUE SOIT ENTIÈREMENT ENLEVÉE. EVITEZ DE
METTRE LA SOLUTION EN CONTACT AVEC LES CIRCUITS. N'UTILISEZ PAS DE JAVELLISANTS OU DEDÉTERGENTS
FORTS; CEUX-CI PEUVENT DÉCOLORER ET CORRODER DIVERS MATÉRIAUX. N'UTILISEZ PAS DE RACLEURS EN MÉTAL,
D'OBJETS POINTUS, DE LAINE D'ACIER, DE TAMPONS À RÉCURER, D'ABRASIFS OU DE SOLVANTS SUR LE DISTRIBUTEUR.
N'UTILISEZ PAS DE L'EAU CHAUDE DE PLUS DE 140 DEGRÉS F (60 DEGRÉS C). CECI PEUT ENDOMMAGER LE DISTRIBU-
TEUR
16
CONTINUED ON NEXT PAGE