lancer Flavor Select 30 Installation And Service Manual
  1. Manuals
  2. Brands
  3. lancer Manuals
  4. Ice Maker
  5. Flavor Select 30
  6. Installation and service manual

lancer Flavor Select 30 Installation And Service Manual

Ice beverage dispenser
Hide thumbs Also See for Flavor Select 30:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
Flavor Select 30 (FS30)
Ice Beverage Dispenser
Installation and Service Manual
PN: 28-0558/04
LANCER CORP
6655 Lancer Blvd.
San Antonio, Texas 78219
To order parts, call
Customer Service: 800-729-1500
Warranty/Technical Support: 800-729-1550
Email: custserv@lancercorp.com
ISO 9001:2000 Quality System Certified
www.lancercorp.com
Manual PN: 28-0558/04
"Lancer" is the registered trademark of Lancer © 2013 by Lancer, all rights reserved.
JULY 2008

Advertisement

Table of Contents
loading

Related Manuals for lancer Flavor Select 30

Summary of Contents for lancer Flavor Select 30

  • Page 1 San Antonio, Texas 78219 To order parts, call Customer Service: 800-729-1500 Warranty/Technical Support: 800-729-1550 Email: custserv@lancercorp.com ISO 9001:2000 Quality System Certified www.lancercorp.com Manual PN: 28-0558/04 “Lancer” is the registered trademark of Lancer © 2013 by Lancer, all rights reserved. JULY 2008...

  • Page 2: Table Of Contents

    ADJUSTING WATER FLOW AND WATER TO SYRUP RATIO (BRIX)......22 CARBONATOR PUMP MODIFICATIONS................23 4. TROUBLESHOOTING......................24-29 5. ILLUSTRATIONS, PARTS LISTINGS, AND WIRING DIAGRAMS FINAL ASSEMBLY......................30-31 ICE CHUTE ASSEMBLY......................32 PELLET ICE ASSEMBLY AND PARTS LISTING..............33 LANCER FLOW CONTROL VALVE (LFCV)...............34 WIRING DIAGRAM......................35 PLUMBING DIAGRAM WITH VALVE WIRING..............36 FS30COUNTER CUTOUT....................37...

  • Page 3: About The Fs30 Dispensers

    Installation and Operation Manual PN 28-0580/03 ABOUT THE FS30 The FS30 is designed using the highest quality materials and state-of-the-art technology providing our customers with consistent quality and a unique drink experience. FS30 SPECIFICATIONS 26 1/2” (673 mm) 30” (762 mm) 14 5/8”...

  • Page 4: Pre-Installation Checklist

    Flavor Select (FS) 22 Ice Beverage Dispenser PRE-INSTALLATION CHECKLIST BEFORE GETTING STARTED Each unit is tested under operating conditions and is thoroughly inspected before shipment. At the time of shipment, the carrier accepts responsibility for the unit. Upon receiv- ing the unit, carefully inspect the carton for visible damage. If damage exists, have the car- rier note the damage on the freight bill and file a claim with carrier.

  • Page 5: Safety/Warnings

    Installation and Operation Manual PN 28-0580/03 WARNING/ADVERTENCIA/AVERTISSEMENT The dispenser is for indoor use only. This appliance is intended for use in commercial applications such as res- taurants, stores or similar. This unit is not a toy. It should not be used by children or infirm persons without supervi- sion.
  • Page 6 Flavor Select (FS) 22 Ice Beverage Dispenser ELECTRICAL WARNING/ADVERTENCIA ELéCTRICA/ AVERTISSEMENT ÉLECTRIQUE Check the dispenser serial number plate for correct electrical requirements of unit. Do not plug into a wall electri- cal outlet unless the current shown on the serial number plate agrees with local current available. Follow all local electrical codes when making connections.
  • Page 7 L’installateur est responsable d'assurer la conformité. ICE INFORMATION Dispensers using cubed ice may also use pellet ice if properly configured. Contact Lancer Customer Service or your Sales Representative for more information.Lancer dispensers will not dispense shaved or flaked ice. Do use bagged ice.

  • Page 8: Installation

    Flavor Select (FS) 22 Ice Beverage Dispenser 1. INSTALLATION BEFORE GETTING STARTED Each unit is tested under operating conditions and is thoroughly inspected before shipment. At the time of shipment, the carrier accepts responsibility for the unit. Upon receiving the unit, carefully inspect the carton for visible damage.

  • Page 9: Selecting A Location For The Dispenser

    B. Sufficient clearance must be provided, if an ice maker is not installed, to allow filling the ice compartment from a five gallon bucket (a minimum of 16 inches (106.4 mm) is recommended), refer to Fig 3. Lancer does NOT recommend the use of shaved or flake ice in the dispenser.

  • Page 10: Installing An Icemaker

    B. An adapter plate is required when installing an icemaker. Contact your Sales Representative or Lancer Customer Service for more information. C. A bin thermostat is required in order to control the level of ice in the dispenser (Refer to WARNING below).

  • Page 11: Connecting To Water Supply Lines

    If the static water pressure exceeds 50 PSI (0.345 MPA), install a water regulator before the carbonator water inlet. The Lancer Water Booster/Tank (PN MC-163172) is offered as a kit. The water booster must be installed as close as possible to the plain water circuit inlet.

  • Page 12: Installation Overview - 1 And 2

    Flavor Select (FS) 22 Ice Beverage Dispenser 1.7 INSTALLATION OVERVIEW Figure 6. FS30-1...
  • Page 13 Installation and Operation Manual PN 28-0580/03 Figure 7. FS30-2...

  • Page 14: Connecting Co2

    C. Connect the plain water supply line and the water supply for the carbonator to the 3/8 inch barb fittings at the front of the unit. NOTE: Install the water regulator (Lancer PN 18-0306) as close as possible to the water carbonator pump inlet. Refer to Figure 6.
  • Page 15 Installation and Operation Manual PN 28-0580/03 1.10 INSTALLING THE FS30 DISPENSER, CONTINUED Install the cup rest and splash plate. Connect the power cord to a grounded electrical outlet. ! AGITATION WARNING THE BIN AGITATION SYSTEM WILL OPERATE AUTOMATICALLY. DO NOT PLACE HANDS IN THE BIN OR THE ICE CHUTE.

  • Page 16: Cleaning And Sanitizing

    If other equipment is being cleaned, follow the guide lines established by the manufacturer for that equipment. B. Lancer equipment (new or reconditioned) is shipped from the factory cleaned and sanitized in accordance with NSF guidelines. The equipment must be cleaned and sanitized after installation is complete.

  • Page 17: Daily Cleaning

    E. Fill a cup with clean warm water and rinse nozzle body. Make certain that the nozzle o-ring is not torn or otherwise damaged. If necessary, replace damaged o-ring with Lancer PN 02-0231. G. Wet the inner surface of the nozzle housing with water and reinstall the nozzle housing by sliding it over the nozzle body and turning clockwise to lock in position.
  • Page 18 Flavor Select (FS) 22 Ice Beverage Dispenser G. WHITE WHEEL SHROUD (PELLET ICE) G. BLACK WHEEL SHROUD (CUBED ICE) Remove the gasket which secures the shroud by Remove the dispensing wheel shroud. pulling it out. Push the front section of the shroud back. Remove the lower ice chute assembly.

  • Page 19: Cleaning/Sanitizing Beverage Components - Bag-In-Box Systems

    Installation and Operation Manual PN 28-0580/03 CLEANING AND SANITIZING BEVERAGE COMPONENTS - BAG-IN-BOX SYSTEMS NOTE: Extended lengths of product lines may require more time to flush and rinse lines. A. Disconnect the syrup quick disconnect coupling from the syrup packages and connect the coupling to a bag valve removed from an empty Bag-in-Box (BIB) package.

  • Page 20: How To Operate And Adjust The Dispenser

    E. Top off cup as desired. PROGRAMMING AND SETUP SOFTWARE NOTE: Lancer reserves the right to make changes and updates as required. If you have any questions regarding the latest versions of programs, please contact your Lancer representative. The Lancer FS22 has been factory preset to the settings necessary to comply with the brand/flavor version of the unit requested by the customer.
  • Page 21 Installation and Operation Manual PN 28-0580/03 MENUS AND SUBMENUS Bonus Flavors a. Decide if the bonus flavors will be set to add an injected flavor to the brands or dispense carbonated water/plain water. b. Choose the Valve number (1-4) by scrolling UP and DOWN arrows. c.

  • Page 22: Purging The Carbonation System

    Activate dispensing valve to fill separator syrup tube. G. Hold a Lancer brix cup under the syrup separator and dispense water and syrup into cup for four seconds. Divide number of ounces of water in cup by four to determine water flow rate per second.

  • Page 23: Carbonator Pump Modifications

    Installation and Operation Manual PN 28-0580/03 CARBONATOR PUMP MODIFICATIONS The electric, positive displacement rotary vane pump with 170 PSI bypass should only be serviced by trained personnel. To achieve optimum carbonation, use filtered water with the pump. A. Turn off power to the dispenser. B.

  • Page 24: Troubleshooting

    Flavor Select (FS) 22 Ice Beverage Dispenser 4. TROUBLESHOOTING TROUBLE CAUSE REMEDY 4.1 No product when switch is A. Keyswitch is off, or keyswitch A. Turn keyswitch on and/or activated. (Switch panel does not harness is disconnected. reconnect keyswitch harness. light up when activated.) B.
  • Page 25 Installation and Operation Manual PN 28-0580/03 TROUBLE CAUSE REMEDY 4.7 Valves do not operate. A. Keyswitch is off, or keyswitch A. Turn keyswitch and/or make harness is disconnected. sure keyswitch harness is con- nected. B. Circuit breaker tripped. B. Reset circuit breaker. C.
  • Page 26 Flavor Select (FS) 22 Ice Beverage Dispenser TROUBLE CAUSE REMEDY 4.14 Insufficient syrup flow. A. Insufficient CO2 pressure to A. Adjust CO2 pressure to 80 PSI, BIB pumps. 5.5 bar (min 70 PSI, 4.8 bar) for BIB pumps. B. Shutoff on mounting block not B.
  • Page 27 Installation and Operation Manual PN 28-0580/03 TROUBLE CAUSE REMEDY 4.17 Valve will not shut off. A. Debris in solenoid seat. A. Activate valve a few times to free debris. Remove the solenoid coil and plunger and clean out foreign material. B.
  • Page 28 Flavor Select (FS) 22 Ice Beverage Dispenser TROUBLE CAUSE REMEDY 4.22 Circuit breaker tripping. A. Valve wire harnesses shorted A. Detect short by disconnecting to itself or faucet plate. valve harnesses from switch panel (2 25-pin harnesses and 2 9-pin harnesses).
  • Page 29 Installation and Operation Manual PN 28-0580/03 TROUBLE CAUSE REMEDY 4.26 BIB pump fails to restart after A. BIB connector not on tight. A. Tighten BIB connector. bag replacement. B. BIB connector is stopped up. B. Clean out or replace BIB connector.

  • Page 30: Illustrations, Parts Listings And Wiring Diagrams

    Flavor Select (FS) 22 Ice Beverage Dispenser 5. ILLUSTRATIONS, PARTS LISTINGS AND WIRING DIAGRAMS FINAL ASSEMBLY 11 12...
  • Page 31 Installation and Operation Manual PN 28-0580/03 5.1 FINAL ASSEMBLY - PARTS LIST Part No. Description 85-14808-12 IBD, Above Counter Multi Brand Series 14800, 115V/60Hz, 8 brands / 12 flavors 85-14810-12 IBD, Above Counter Multi Brand Series 14800, 115V/60Hz, 10 brands / 12 flavors 85-14812-12 IBD, Above Counter Multi Brand Series 14800, 115V/60Hz, 12 brands / 12 flavors 85-14814-12...

  • Page 32: Ice Chute Assembly

    Flavor Select (FS) 22 Ice Beverage Dispenser 5.2 ICE CHUTE ASSEMBLY 7 x2 9 x2 Item Part No. Description 05-2257/01 Chute, Upper, IC 54-0406 Chute, Printed, IBD 05-0999/01 Lever, Chute, IBD 04-0268 Scr, 6-19X.625 LG, PLSTI,HHSW/W 03-0241 Spring, Chute, IBD 12-0244 Switch, SPST, 5A, 250V, 05-0359...

  • Page 33: Pellet Ice Assembly And Parts Listing

    Installation and Operation Manual PN 28-0580/03 5.3 PELLET ICE ASSEMBLY AND PARTS LISTING Use the components listed on this page with pellet ice only. Item Part No. Description 05-2325/01 Ice Shroud, IC 23-1401/01 Agitator Assy, Helical, IC 10-0762 Pin, Hex Design, FS-16 03-0368 Retainer, Pin, Agitator, IBD 82-3651...

  • Page 34: Lancer Flow Control Valve (Lfcv)

    Flavor Select (FS) 22 Ice Beverage Dispenser 5.4 LANCER FLOW CONTROL VALVE (LFCV) LFCV VALVE ASSEMBLIES Valve Assembly 82-3820 LFCV, BONUS INJECTOR 82-3823 LFCV, 3.0 - 4.5, SYRUP ASSY 82-3824 LFCV, 3.0 - 4.5, SODA/WATER ASSY Spare Parts LFCV SPARE PARTS...

  • Page 35: Wiring Diagram

    Installation and Operation Manual PN 28-0580/03 5.5 WIRING DIAGRAM...

  • Page 36: Plumbing Diagram With Valve Wiring

    Flavor Select (FS) 22 Ice Beverage Dispenser 5.6 PLUMBING DIAGRAM WITH VALVE WIRING VALVE HARNESS IS2-1 IS2-2 IS1-3 IS1-2 IS2-3 IS1-1 DIAGRAM S2-4 S2-3 S2-1 S1-4 S1-2 S1-1 SODA2 S2-2 WATER2 WATER1 S1-3 SODA1 IS2-1 IS1-1 S1-1 S1- 3 S2-1 S2- 3 IS2-2 IS1-2...

  • Page 37: Fs30Counter Cutout

    Installation and Operation Manual PN 28-0580/03 5.7 FS22 COUNTER CUTOUT FS30 COUNTER CUTOUT 30” 15/16” 28 1/8” 23” 18 5/8” 15” 30 1/2” 11 1/2” 3“ DIAMETER OPTIONAL 1 1/2” 3“ F R O N T D I S P E N S E R 1 5/8”...
  • Page 38 LANCER To order parts, call Customer Service: 800-729-1500 Warranty: 800-729-1550 Email: custserv@lancercorp.com www.lancercorp.com...

Table of Contents