1. Manuals
  2. Brands
  3. ICPDAS Manuals
  4. Network Router
  5. MSM-6226G
  6. Console manual

ICPDAS MSM-6226G Console Manual

20-port 10/100/1000 base-t + 4 combo 100/1000 tp/sfp port + 2 sfp port l2 managed switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MSM-6226G
GbE M
E
S
anaged
THERNET
WITCH
Console Manual

Advertisement

Table of Contents
loading

Related Manuals for ICPDAS MSM-6226G

Summary of Contents for ICPDAS MSM-6226G

  • Page 1 MSM-6226G GbE M anaged THERNET WITCH Console Manual...
  • Page 2 A N A G E M E N T U I D E MSM-6226G L2 GIGABIT ETHERNET SWITCH 26 Port L2 Plus Managed Switch...

  • Page 3: About This Guide

    BOUT UIDE This guide gives specific information on how to operate and use URPOSE the management functions of the switch. The guide is intended for use by network administrators who are UDIENCE responsible for operating and maintaining network equipment; consequently, it assumes a basic working knowledge of general switch functions, the Internet Protocol (IP), and Simple Network Management Protocol (SNMP).

  • Page 4: Revision History

    Revision History Release Date Revision V1.0 07/29/2013...

  • Page 5: Table Of Contents

    ONTENTS ABOUT THIS GUIDE ......................ii Revision History ........................iii CONTENTS ........................iv 802.1X Commands of CLI..................1 AAA of CLI......................11 Access Commands of CLI ..................22 Account Commands of CLI ..................25 ACL Commands of CLI..................27 Aggregation Commands of CLI................35 Arp-inspection Commands of CLI................38 Auth Commands of CLI..................41 Config-File Commands of CLI ................43 DHCP-Relay Commands of CLI ................44...
  • Page 6 32 MVR of CLI.......................185 33 MVRP of CLI ......................191 Port Commands of CLI ..................196 35 Port-Security Commands of CLI ................207 Privilege Commands of CLI..................209 PVLAN Commands of CLI ..................211 QoS Commands of CLI ..................214 SMTP of CLI ......................234 SNMP of CLI......................242 SSH of CLI ......................254 SYSLOG of CLI ....................256 SYSTEM of CLI....................260...

  • Page 7: 802.1X Commands Of Cli

    802.1X Commands of CLI Table 1: 802.1X Commands Command Function agetime Configure the time in seconds between check for activity on successfully authenticated MAC addresses auto-logout Configure time of inactivity before automatic logout clear Clear 802.1X statistics eapol-timeout Configure the time between EAPOL retransmissions exit Exit from current mode guest-vlan...
  • Page 8 between reauthentications reauthentication Configure the 802.1X reauthentication mode restart Restart 802.1X authentication process restore Restore running configuration save Save running configuration show Show 802.1X information Agetime Configure the time in seconds between check for activity on successfully authenticated MAC addresses YNTAX agetime <10-1000000>...
  • Page 9 XAMPLE eapol-timeout Configure the time between EAPOL retransmissions YNTAX eapol-timeout <1-65535> Parameter <1-65535> Time in seconds between EAPOL retransmissions XAMPLE hold-time Configure the time in seconds before a MAC-address that lied authentication gets a new authentication chance YNTAX hold-time <10-1000000> Paramete <10-1000000>...
  • Page 10 mode Configure the 802.1X mode YNTAX mode <disable> <ensable> Parameter Disable Globally disable 802.1X operation mode enable Globally enable 802.1X operation mode XAMPLE port-guest-vlan Configure the Guest VLAN mode of switch ports YNTAX port-guest-vlan <port-list> <disable> <ensable>...
  • Page 11 Parameter Port list, available value is from 1 to 10B format:1,3-5 . Disable Disable Guest VLAN Enable Enable Guest VLAN XAMPLE port-radius-qos A constant that defines a nonzero number of seconds between periodic reauthentication of the supplicant YNTAX port-radius-qos <port-list> <disable> <ensable> Parameter Port list, available value is from 1 to 10B format:1,3-5 Disable Disable RADIUS-assigned QoS...
  • Page 12 XAMPLE port-state Configure the 802.1X port state YNTAX port-state <port-list> <force-auth> <force-unauth> <mac-based> <multi> <port-based> <single>...
  • Page 13 Parameter Port list, available value is from 1 to 10B format:1,3-5 force-auth Port access is allowed force-unauth Port access is not allowed mac-based Switch authenticates on behalf of the client multi Multiple Host 802.1X Authentication port-based Port-based 802.1X Authentication single Single Host 802.1X Authentication XAMPLE radius-qos Configure the RADIUS-assigned QoS moder...
  • Page 14 radius-vlan Configure the RADIUS-assigned vlan mode YNTAX radius-vlan <disable> <ensable> Parameter disable Disable RADIUS-assigned vlan enable Enable RADIUS-assigned vlan XAMPLE...

  • Page 15: Aaa Of Cli

    AAA of CLI Table : AAA Commands Command Function acc-radius Configure RADIUS accounting Server accounting Configure Accounting mode authorization Configure Authorization mode deadtime Configure server dead time fallback-author Configure Authorization mode radius Configure RADIUS authentication server show Show AAA information tacacs+ Configure TACACS+ authentication server timeout...
  • Page 16 accounting To enable or disable the RADIUS accounting operation mode. Syntax accounting <enable/disable> Parameter <disable> Globally disable Accounting operation mode. <enable> Globally enable Accounting operation mode. EXAMPLE If you didn’t connect the RADIUS Server already then the switch will show “Server disconnect”.
  • Page 17 authorization To configure (enable/disable) RADIUS Authorization mode Syntax authorization <enable/disable> Parameter <disable> Globally disable Authorization operation mode. <enable> Globally enable Authorization operation mode. EXAMPLE deadtime To configure the RADIUS server deadtime. Syntax deadtime <0-3600> Parameter <0-3600> Time that a server is considered dead if it doesn't answer a request. The available value is from 0 to 3600 second Default Setting None...
  • Page 18 fallback-author To configure the fallback function of RADIUS authorization with enable/disable if remote authorization fails. Syntax fallback-author <disable/ enable> Parameter <disable> Disable fallback function. <enable> Enable fallback function if remote authorization fails. EXAMPLE If you didn’t connect the RADIUS Server already then the switch will show “Server disconnect”.
  • Page 19 If you didn’t connect the RADIUS Server already then the switch will show “Server disconnect”. show To display the RADIUS AAA information Syntax Show <config> Show <statistics> <1-5> Parameter <config> To show AAA configuration <statistics> To show RADIUS statistics <1-5> The RADIUS Server Index EXAMPLE...
  • Page 20 tacacs+ To configure the TACACS+ authentication server detail parameter. Syntax tacacs+ <index> <enable/disable> <ip-hostname> <0-65535> <Line> Parameter <index> The TACACS+ authentication Server index. The available value is from 1 to 5 <disable/enable> To enable or disable the TACACS+ authentication service. <ip-hostname>...
  • Page 21 timeout To configure server response timeout Syntax timeout <3-3600> Parameter <3-3600> The Timeout, which can be set to a number between 3 and 3600 seconds, is the maximum time to wait for a reply from a server. EXAMPLE...

  • Page 22: Access Commands Of Cli

    Access Commands of CLI Table : Access Commands Command Function Add or modify access management entry clear Clear access management statistics delete Delete access management entry mode Configure the access management mode show Show access management information Add or modify access management entry YNTAX add <1-16>...
  • Page 23 clear Clear access management statistics YNTAX Clear < statistics> Parameter Clear access management statistics XAMPLE delete Delete access management entry. YNTAX Delete <1-16> Parameter 1-16 Entry index XAMPLE...
  • Page 24 mode Configure the 802.1X mode YNTAX mode <disable> <ensable> Parameter disable Disable access management mode operation enable Enable access management mode operation XAMPLE show Show 802.1X information YNTAX show < config> < statistics> Parameter config Show access management configuration statistics Show access management statistics XAMPLE...

  • Page 25: Account Commands Of Cli

    Account Commands of CLI Table : Account Commands Command Function Add or modify user account delete Delete user account show Show user account information Add or modify user account YNTAX add guest <1-15> <word> Parameter <1-15> User privilege level <WORD> Up to 32 characters to identify the user name XAMPLE delete To create a new operator user.
  • Page 26 XAMPLE show Show user account information YNTAX Show <name> XAMPLE...

  • Page 27: Acl Commands Of Cli

    ACL Commands of CLI Table : ACL Commands Command Function Add or modify Access Control Entry action Configure ACL port default action clear Clear all ACL counters delete To delete the ACE ( Access Control Entry) configuration on the switch. logging Configure ACL port default logging operation.
  • Page 28 list. If the next ACE ID is zero, the ACE will be placed last in the list. policy Policy ACE keyword, the rule applies to all ports configured with the specified policy port Port ACE keyword, the rule applies to the specified port only switch Switch ACE keyword, the rule applies to all ports <port-list>...
  • Page 29 YNTAX action <port-list> <deny> <permit>. Parameter <port-list> Port list, available value is from 1 to 10B format:1,3-5pe deny Deny forwarding permit Permit forwarding EXAMPLE delete This command delete the ACE ( Access Control Entry) configuration on the switch. YNTAX delete <1-256>...
  • Page 30 YNTAX list <port-list> disable/enable Parameter <port-list> Port list, available value is from 1 to 10B format:1,3-5 disable Frames received on the port are not logged enable Frames received on the port are stored in the system log EXAMPLE mirror Configure ACL port default mirror operation. YNTAX list <port-list>...
  • Page 31 XAMPLE policy This command set acl port policy on switch. YNTAX policy <port-list> <1-8> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3-5 <1-8> Policy number XAMPLE port-rate This command set acl port policy on switch. YNTAX port-rate <port-list>...
  • Page 32 ratelimiter This command access control rule with rate limiter on switch. YNTAX ratelimiter <1-16> <kbps> <0-10000> Parameter <1-16> Rate limiter ID kbps Kbits per second Packets per second <0-10000> Rate in 100Kbps XAMPLE show This command show all access control entry setting on switch. YNTAX show Parameter...

  • Page 35: Aggregation Commands Of Cli

    Aggregation Commands of CLI Table : Aggregation Commands Command Function delete Delete command group Configure the link aggregation group mode Configure the link aggregation traffic distribution mod show Show aggregation group information delete To Delete command YNTAX delete Parameter group Delete link aggregation group XAMPLE Group...
  • Page 36 Parameter <1-5> Aggregation group id <port-list> Port list, available value is from 1 to 10B format:1,3- XAMPLE mode To set sender description. YNTAX set sender < ip > <disable> Parameter dmac Destination MAC address Source and destination IP address port Source and destination UDP/TCP port smac Source MAC address disable...

  • Page 38: Arp-Inspection Commands Of Cli

    Arp-inspection Commands of Table : Arp-inspection Commands Command Function Add ARP inspection static entry delete Delete ARP inspection static entry mode Configure ARP inspection mode port-mode Configure ARP inspection port mode show Show ARP inspection information Add ARP inspection static entry YNTAX add <port-list>...
  • Page 39 mode Configure ARP inspection mode YNTAX Delete < disable> < enable> Parameter disable Globally disable ARP inspection mode enable Globally enable ARP inspection mode. EXAMPLE port-mode Configure ARP inspection port mode YNTAX Delete <port-list> < disable> < enable> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- disable Globally disable ARP inspection mode enable Globally enable ARP inspection mode.
  • Page 40 Show Configure ARP inspection port mode YNTAX status Show < config> < > Parameter config Show ARP inspection configuration status Show ARP inspection static and dynamic entry EXAMPLE Publication date: Aug., 2011 Revision A1...

  • Page 41: Auth Commands Of Cli

    Auth Commands of CLI Table : Auth Commands Command Function fallback Configure local authentication fallback method Configure authentication method show Show Authentication configuration fallback Configure local authentication fallback YNTAX add < console> < ssh > < telnet > < web > /< disable >< disable > Parameter console Settings for console ssh Settings for ssh...
  • Page 42 EXAMPLE Show Show Authentication configuration YNTAX Show EXAMPLE Publication date: Aug., 2011 Revision A1...

  • Page 43: Config-File Commands Of Cli

    Config-File Commands of CLI Table : Config-file Commands Command Function export Export configuration file to tftp server import Import configuration file to flash export To run the export function. YNTAX export < ip-address> <WORD> Parameter ip-address The TFTP server ip address <WORD>...

  • Page 44: Dhcp-Relay Commands Of Cli

    DHCP-Relay Commands of CLI Table : DHCP-Relay Commands Command Function clear Clear DHCP relay statistics mode onfigure DHCP relay mode relay-option Configure DHCP relay agent information option server Configure DHCP relay server show Show DHCP relay information clear Clear DHCP relay statistics YNTAX clear <...
  • Page 45 EXAMPLE relay-option Configure DHCP relay agent information option YNTAX relay-option<enable> <disable> Parameter disable Disable DHCP relay mode enable Enable DHCP snooping mode.When enable DHCP relay mode operation, the agent forward and to transfer DHCP messages between the clients and the server when they are not on the same subnet domain.
  • Page 46 show Show DHCP relay information YNTAX set entry < config> < statistics> Parameter config Show DHCP relay configuration statistics Show DHCP relay statistics set entry <vid> vid range from 1 to 4094 EXAMPLE Publication date: Aug., 2011 Revision A1...

  • Page 47: Dhcp Snooping Commands Of Cli

    DHCP SNOOPING Commands of CLI Table : dhcp_snooping Commands Command Function clear Clear DHCP snooping statistics mode Configure DHCP snooping mode port-mode Configure DHCP snooping port mode show Show DHCP snooping information clear Clear DHCP snooping statistics YNTAX Clear <statistics><port-list> Parameter statistics Clear DHCP snooping statistics <port-list>...
  • Page 48 EXAMPLE port-mode configure DHCP snooping port mode YNTAX Mode <port-list> < trusted > Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- trusted Configures the port as trusted sources of the DHCP message untrusted Configures the port as untrusted sources of the DHCP message EXAMPLE show Show DHCP snooping information...
  • Page 49 Publication date: Aug., 2011 Revision A1...

  • Page 50: Diagnostic Commands Of Cli

    Diagnostic Commands of CLI Table : Diagnosic Commands Command Function ping Uses the ICMP protocol's mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway ping6 Uses the ICMP protocol's mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway veriphy Run cable diagnostics...
  • Page 51 veriphy Run cable diagnostics YNTAX veriphy <port-list> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- EXAMPLE Publication date: Aug., 2011 Revision A1...

  • Page 52: Eee Of Cli

    EEE of CLI Table : EEE Commands Command Function mode Configure EEE mode show Show EEE information urgent-queue Configure EEE urgent queue mode To configure the port Energy Efficient Ethernet mode Syntax mode <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable>...
  • Page 53 urgent-queue To configure the port EEE urgent-queue...
  • Page 54 Syntax urgent-queue <port-list> <queue-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <queue-list> Queue list, format : 1,3-5 <disable> Queue will postpone the transmission until 3000 bytes are ready to be transmitted. <enable> Queues set will activate transition of frames as soon as any data is available EXAMPLE...

  • Page 55: Event Commands Of Cli

    Event Commands of CLI Table : event Commands Command Function group Configure trap event severity leve show Show trap event configuration group Configure trap event severity level YNTAX Group <group-name><port-list> Parameter <group-name> Trap event group name <0-7> Severity level <0> Emergency: system is unusable <1>...
  • Page 56 Show Show trap event configuration YNTAX Show EXAMPLE...

  • Page 57: Firmware Commands Of Cli

    Firmware Commands of CLI Table :Firmware Commands Command Function upgrade Upgrade system firmware upgrade Upgrade system firmware YNTAX firmware< <ipv6-address>>< ip-hostname> <WORD> Parameter <ipv6-address> TFTP server ipv6 address IPv6 address is in 128-bit records represented as eight fields of up to four hexadecimal digits with a colon separates each field (:).For example, 'fe80::215:c5ff:fe03:4dc7'.

  • Page 58: Garp Of Cli

    GARP of CLI Table : GARP Commands Command Function applicant Enable/Disable applicant administrative control join-time Set the GARP join timer configuration leave-all Set the GARP leave all timer configuration leave-time Set the GARP leave timer configuration show Show the GARP configuration applicant To enable/disable applicant administrative control Syntax...
  • Page 60 EXAMPLE If you didn’t set the GARP environment already then the switch will show “Set jointimer failed”. leave-all To set the GARP leave all timer configuration Syntax leave-all <port-list> <timer-value> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <timer-value>...
  • Page 61 EXAMPLE If you didn’t set the GARP environment already then the switch will show “Set leavetimer failed”. show To show the GARP configuration Syntax show <statistic> <port-list> Parameter <statistic> Show the basic GARP port statistics <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE If you didn’t set the GARP environment already then the switch will show “empty field value”.

  • Page 62: Gvrp Of Cli

    GVRP of CLI Table : GVRP Commands Command Function clear Clear the basic GVRP port statistics control Enable/ Disable GVRP globally mode Enable/ Disable GVRP on port rrole Enable/ Disable GVRP restricted role on port show Show the GVRP configuration clear To clear the basic GVRP port statistics Syntax...
  • Page 63 Parameter <disable> To disable GVRP function globally. <enable> To enable GVRP function globally. EXAMPLE mode To enable or disable GVRP function on port. Syntax mode <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable>...
  • Page 64 EXAMPLE show To show the GVRP function information Syntax show <config> show <statistics> Parameter <config> To show the GVRP configuration. <statistics> To show the basic GVRP port statistics.
  • Page 65 EXAMPLE...

  • Page 66: Https Commands Of Cli

    Https Commands of CLI Table : Https Commands Command Function mode Configure the HTTPS mode redirect Configure the HTTPS redirect mode show Show HTTPS configuration mode Configure the HTTPS mode YNTAX mode<disable><enable> Parameter disable Disable HTTPS mode operation enable Enable HTTPS mode operation EXAMPLE redirect Configure the HTTPS redirect mode...
  • Page 67 EXAMPLE show Show HTTPS configuration YNTAX Show EXAMPLE...

  • Page 68: Igmp Commands Of Cli

    IGMP Commands of CLI Table : igmp Commands Command Function fast-leave Set per-port Fast Leave filtering The IP Multicast Group that will be filtered flooding Set IGMP Flooding Mode leave-proxy Set IGMP Leave Proxy Mode lmqi Set per-VLAN Last Member Query Interval proxy Set IGMP Proxy Mode...
  • Page 69 EXAMPLE leave-proxy Set IGMP Leave Proxy Mode YNTAX Mode <disable><enable> Parameter disable Disable IGMP Leave Proxy enable Enable IGMP Leave Proxy EXAMPLE lmqi Set per-VLAN Last Member Query Interval YNTAX Mode <port-list> trusted Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- trusted Configures the port as trusted sources of the DHCP message untrusted Configures the port as untrusted sources of the DHCP message EXAMPLE...
  • Page 70 proxy Set IGMP Proxy Mode YNTAX Mode <disable><enable> Parameter disable Disable IGMP Proxy enable Enable IGMP Proxy EXAMPLE Set per-VLAN Query Interval YNTAX Qi <vlan-list> <1-255> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <1-255> Range:1~255 sec, Default:125 sec EXAMPLE Set per-VLAN Query Response Interval.
  • Page 71 querier Set per-VLAN IGMP Querier YNTAX Qri <vlan-list> <disable><enable> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 disable Disable per-VLAN IGMP Querier enable Enable per-VLAN IGMP Querier EXAMPLE router Set Router Port YNTAX Router <port-list><disable><enable> Parameter <port-list>...
  • Page 72 Set per-VLAN Robustness Variable YNTAX Rv <vlan-list> <1-255> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <1-255> Range:1~255, Default:2 EXAMPLE show Show IGMP Snooping information YNTAX show < config> < statistics> Parameter config Show IGMP Snooping Configuration groups Entries in the IGMP Group Table Entries in the IGMPv3 Information Table...
  • Page 74 snooping Set IGMP Snooping Mode YNTAX Snooping <disable><enable> Parameter disable Disable the Global IGMP Snooping enable Enable the Global IGMP Snooping EXAMPLE state Enable/Disable per-VLAN IGMP Snooping Mode YNTAX Snooping <vlan-list><disable><enable> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 disable Disable per-VLAN IGMP Snooping enable...
  • Page 75 throttling Set per-port Throttling YNTAX Snooping <port-list> <0-10> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <0-10> Set Port Group Limit numberm, Range:0~10, 0:unlimited EXAMPLE Set per-VLAN Unsolicited Report Interval YNTAX Snooping <vlan-list><0-31744> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <0-31744>...

  • Page 76: Ip Commands Of Cli

    IP Commands of CLI Table : ip Commands Command Function dhcp Enable/Disable DHCP client mgmt-vlan Set the management VLAN ID name-server Set DNS IP address setup Set the IP address show Show ip information dhcp Enable/Disable DHCP client YNTAX Dhcp <disable><enable> Parameter disable Disable DHCP client...
  • Page 77 Parameter <1-4094> Management VLAN ID, available value is from 1 to 4094s. EXAMPLE name-server Set DNS IP address YNTAX name-server <ip-address> Parameter <ip-address> DNS IP address EXAMPLE Setup Set the IP address YNTAX Setup <ip-address><ip-mask><ip-address> Parameter <ip-address> IP address <ip-mask> IP subnet mask <ip-address>...
  • Page 78 show Show ip information YNTAX Show EXAMPLE...

  • Page 79: Ip-Source-Guard Of Cli

    IP-Source-Guard of CLI Table : IP-Source-Guard Commands Command Function Add or modify IP source guard static entry delete Delete IP source guard static entry limit IP source guard port limitation for dynamic entries mode Configure IP source guard mode port-mode Configure IP source guard port mode show Show IP source guard configuration...
  • Page 80 delete To delete IP source guard static entry Syntax delete <port-list> <VLAN ID> <ip-address> <mac-address> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5.. <VLAN ID> VLAN ID, available value is from 1 to 4094 <ip-address> IP address allowed for doing IP source guard <mac-address>...
  • Page 82 mode To configure IP source guard mode globally. Syntax mode <disable/ enable> Parameter <disable> Globally disable IP source guard mode. <enable> Globally enable IP source guard mode. All configured ACEs will be lost when the mode is enabled. EXAMPLE port-mode To configure IP source guard port mode.
  • Page 84 show To show IP source guard information Syntax show <binding-table> <port-list> show <config> Parameter <binding-table> Show IP-MAC binding table. <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <config> Show IP source guard configuration. EXAMPLE...

  • Page 85: Ipv6 Commands Of Cli

    IPV6 Commands of CLI Table : IPV6 Commands Command Function autoconfig Configure IPv6 autoconfig mode setup Set the IPv6 address show Show IPv6 information autoconfig Configure IPv6 autoconfig mode YNTAX Autoconfig <disable><enable> Parameter disable Disable autoconfig mode enable Enable autoconfig mode EXAMPLE Setup Set the IPv6 address...
  • Page 86 show Show ipv6 information YNTAX Show EXAMPLE...

  • Page 87: Lacp Commands Of Cli

    LACP Commands of CLI Table : LACP Commands Command Function clear Clear command Configure the LACP key mode Configure the LACP mode role Configure the LACP role show Show LACP information clear Clear command YNTAX clear < statistics> Parameter statistics Clear LACP statistics EXAMPLE Configure the LACP key...
  • Page 88 EXAMPLE mode Configure the LACP mode YNTAX mode <disable><enable> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- disable Disable LACP protocol enable Enable LACP protocol EXAMPLE role Configure the LACP mode YNTAX role <disable><enable> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- active Initiate LACP negotiation, and transmit LACP packets each second passive Listen for LACP packets EXAMPLE...
  • Page 89 Show Show LACP information YNTAX Show Parameter config Show LACP configuration statistics Show LACP statistics status Show LACP status EXAMPLE...

  • Page 91: Limit-Control Commands Of Cli

    Limit-control Commands of CLI Table : Limit-control Commands Command Function action Configure the action involved with exceeding the limit aging Configure the aging mode and period limit Configure the max. number of MAC addresses that can be learned on the port mode Configure the global limit control mode...
  • Page 93 aging Configure the aging mode and period YNTAX aging<disable><enable> Parameter disable Disable aging enable Enable aging EXAMPLE limit Configure the max. number of MAC addresses that can be learned on the port YNTAX limit<port-list><1-1024> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <1-1024>...
  • Page 94 Parameter disable Globally disable port security enable Globally enable port security EXAMPLE port-mode Configure the port mode YNTAX port-mode <port-list><disable><enable> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- disable Disable port security on selected port enable Enable port security on selected port EXAMPLE reopen Reopen one or more ports whose limit is exceeded and...
  • Page 95 EXAMPLE show Show limit control configuration YNTAX Show EXAMPLE...

  • Page 96: Lldp Commands Of Cli

    LLDP Commands of CLI Table : LLDP Commands Command Function cdp-aware Configure CDP (Cisco Discovery Protocol) aware mode clear Clear LLDP statistics delay Configure LLDP Tx delay hold Configure LLDP Tx hold value interval Configure LLDP transmission interval mode Configure the LLDP mode option-tlv Configure LLDP Optional TLVs...
  • Page 97 clear Clear LLDP statistics YNTAX clear EXAMPLE delay Configure LLDP Tx delay YNTAX limit<1-8192> Parameter <1-8192> LLDP transmission delay EXAMPLE Interval Configure LLDP transmission interval YNTAX Interval <5-32768> Parameter <5-32768> LLDP transmission interval...
  • Page 98 EXAMPLE mode Configure the LLDP mode YNTAX Mode<port-list> <disable><enable> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- disable The switch will not send out LLDP information, and will drop LLDP information received from neighbours enable The switch will send out LLDP information, and will analyze LLDP information received from neighbours rx-only The switch will not send out LLDP information, but LLDP information from neighbour units is analyzed tx-only The switch will...
  • Page 99 sys-capa System capability sys-desc System description sys-name System name disable Disable TLV enable Enable TLV EXAMPLE reinit Configure LLDP reinit delay YNTAX reinit <1-10> Parameter <1-10> LLDP reinit delay EXAMPLE show Show LLDP information YNTAX Show Parameter config Show LLDP configuration info Show LLDP neighbor device information statistics Show LLDP statistics...
  • Page 100 EXAMPLE...

  • Page 102: Lldp-Med Of Cli

    LLDP-MED of CLI Table : LLDPMED Commands Command Function civic Configure LLDP-MED civic address location additional-code Additional code additional-info Additional location info apartment Unit (Apartment, suite) block Neighbourhood, block building Building (structure) city City, township, shi (Japan) comm.-name Postal community name country-code The two-letter ISO 3166 country code county...
  • Page 103 latitude Latitude longitude Longitude delete Delete the selected policy Configure LLDP-MED Emergency Call Service fast Configure LLDP-MED fast start repeat count policy Configure LLDP-MED policy show Show LLDP-MED information civic To configure LLDP-MED civic address location Syntax civic additional-code <LINE> Parameter <LINE>...
  • Page 104 Syntax civic block <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic building<LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic city<LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic comm.-name<LINE>...
  • Page 105 ISO 3166 country code. EXAMPLE Syntax civic country <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic district <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic floor <LINE> Parameter <LINE>...
  • Page 106 Syntax civic house-no-suffix <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic landmark <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic leading-street-direction <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic name <LINE>...
  • Page 107 EXAMPLE Syntax civic place-type <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic room-number <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic state <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic street <LINE>...
  • Page 108 Syntax civic street-suffix <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic trailing-street-suffix <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE Syntax civic zip-code <LINE> Parameter <LINE> The value for the Civic Address Location entry. EXAMPLE...
  • Page 109 coordinate To configure LLDP-MED coordinate location Syntax coordinate altitude <coordinate-value> <floor/ meter> Parameter <coordinate-value> Meters or floors with max. 4 digits. <floor> Representing altitude in a form more relevant in buildings which have different floor-to-floor dimension <meter> Representing meters of Altitude defined by the vertical datum specified EXAMPLE Syntax...
  • Page 110 Syntax coordinate latitude <coordinate-value> <north/ south> Parameter <coordinate-value> 0 to 90 degrees with max. 4 digits. <north> North of the equator <south> South of the equator EXAMPLE Syntax coordinate longitude <coordinate-value> <east/ west> Parameter <coordinate-value> 0 to 180 degrees with max. 4 digits. <east>...
  • Page 111 delete To delete the selected policy Syntax delete <policy ID> Parameter <policy ID> Policy ID, available value is from 0 to 31. EXAMPLE To configure LLDP-MED Emergency Call Service Syntax ecs <number> Parameter <number> The numerical digit string for the Emergency Call Service. EXAMPLE fast To configure LLDP-MED fast start repeat count...
  • Page 112 policy To configure LLDP-MED policy Syntax policy <tagged/ untagged> <VLAN ID> < Layer2 priority> <DSCP value> <guest-voice/ guest-voice-signaling/ softphone-voice/ streaming-video/ video-conferencing/ video-signaling/ voice/ voice-signaling> Parameter <tagged> The device is using tagged frames. <untagged> The device is using untagged frames <VLAN ID> VLAN ID, available value is from 1 to 4094. <L2 priority>...
  • Page 113 isolation from data applications. <voice-signaling> Voice Signaling (conditional) for use in network topologies that require a different policy for the voice signaling than for the voice media EXAMPLE port-policy To configure LLDP-MED port policy Syntax port-policy <port-list> <policy ID> <disable/ enable> Parameter <port-list>...
  • Page 114 Syntax show <info> <port-list> Parameter <info> Show LLDP-MED neighbor device information . <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE Syntax show <policy> Parameter <policy> Show LLDP-MED policy configuration . EXAMPLE...
  • Page 115 Syntax show <port-policy> Parameter <port-policy> Show LLDP-MED port policy configuration . EXAMPLE...

  • Page 116: Mac Commands Of Cli

    MAC Commands of CLI Table :MAC Commands Command Function age-time Configure aging time of MAC address delete Delete commands flush Flush out dynamic learned MAC address learning Configure learning mode of switch ports show Show MAC address table information static-mac Configure static MAC address age-time...
  • Page 117 <1-4094> VLAN ID, available value is from 1 to 4094...
  • Page 118 EXAMPLE flush Flush out dynamic learned MAC address YNTAX flush EXAMPLE learning Configure learning mode of switch ports YNTAX learning<port-list>< auto> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- auto Learning is done automatically as soon as a frame with unknown SMAC is receiveddisable Disable learning secure Only static MAC entries are learned, all other frames EXAMPLE...
  • Page 119 show Configure LLDP-MED fast start repeat count YNTAX Show Parameter configuration Show MAC address table configuration mac-table Show MAC address table static-mac Show static MAC address EXAMPLE...

  • Page 120: Mirror Commands Of Cli

    Mirror Commands of CLI Table: Mirror Commands Command Function analyzer-port Configure analyzer port analyzer-port Configure port mod show Show port mirroring information analyzer-port Configure LLDP-MED civic address location YNTAX analyzer-port < disable > Parameter disable Disable port mirroring <port> Analyzer port, available value is from 1 to 10 EXAMPLE port-mode Configure LLDP-MED coordinate location...
  • Page 121 EXAMPLE show Show port mirroring information YNTAX Show EXAMPLE...

  • Page 122: Mld Commands Of Cli

    MLD Commands of CLI Table :MLD Commands Command Function fast-leave Set per-port Fast Leave filtering The IP Multicast Group that will be filtered flooding Set MLD Flooding Mode leave-proxy Set MLD Leave Proxy Mode lmqi Set the per-VLAN Last Member Query Interval proxy Set MLD Proxy Mode Set the per-VLAN Query...
  • Page 123 disable Disable Fast Leave enable Enable Fast Leave EXAMPLE filtering The IP Multicast Group that will be filtered YNTAX filtering Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <ip-address> IPv6 address is in 128-bit records represented as eight fields of up to four hexadecimal digits with a colon separates each field (:).
  • Page 124 disable Disable unregistered IPMCv6 traffic flooding enable Enable unregistered IPMCv6 traffic floodingq...
  • Page 125 EXAMPLE leave-proxy Set MLD Leave Proxy Mode YNTAX leave-proxy<disable> Parameter disable Disable MLD Leave Proxy enable Enable MLD Leave Proxy EXAMPLE lmqi Set the per-VLAN Last Member Query Interval YNTAX Lmqi <vlan-list><0-31744> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <0-31744>...
  • Page 126 YNTAX policy <disable><enable> Parameter disable Disable MLD Proxy enable Enable MLD Proxy EXAMPLE Set the per-VLAN Query Interval YNTAX qi <vlan-list><1-255><1-255> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <1-255> Range:1~255 sec, Default:125 sec <1-255> Range:1~255 sec, Default:125 sec EXAMPLE Set the per-VLAN Query Response Interval YNTAX...
  • Page 127 Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <0-31744> Range:0~31744 tenths of sec, Default:100 tenths of sec EXAMPLE querier Enable/Disable the per-VLAN MLD Querier YNTAX querier<vlan-list>< disable > Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 disable Disable the per-VLAN MLD Querier enable...
  • Page 128 EXAMPLE set the per-VLAN Robustness Variable YNTAX rv<vlan-list><2-255> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <2-255> Range:2~255, Default:2 EXAMPLE show Show MLD Information YNTAX Show Parameter config Show MLD Configuration groups Entries in the MLD Group Table Entries in the MLDv2 Information Table status Show MLD Status...
  • Page 130 snooping Set MLD Snooping Mode YNTAX snooping< disable > Parameter disable Disable the Global MLD Snooping enable Enable the Global MLD Snooping EXAMPLE state Enable/Disable the per-VLAN MLD Snooping YNTAX state<vlan-list><0-31744> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 disable Disable the per-VLAN MLD Snooping enable Enable the per-VLAN MLD Snooping EXAMPLE...
  • Page 131 throttling Set per-port Throttling YNTAX Throttling <port-list><0-10> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <0-10> Set Port Group Limit number, Range:0~10, 0:unlimited EXAMPLE t the per-VLAN Unsolicited Report Interval YNTAX uri<vlan-list><0-31744> Parameter <vlan-list> VLAN list, available value is from 1 to 4094 format: 1,3-5 <0-31744>...

  • Page 132: Mrp Of Cli

    MRP of CLI Table : MRP Commands Command Function applicant Enable/Disable applicant administrative control join-time Set the MRP join timer configuration leave-all Set the MRP leave all timer configuration leave-time Set the MRP leave timer configuration periodic Enable/Diable periodic tx timer show Show the MRP information applicant...
  • Page 133 <time-value> join time value, available value is from 200 to 400 seconds.
  • Page 134 EXAMPLE If you didn’t set the MRP environment already then the switch will show “Set join timer failed”. leave-all To set the MRP leave all timer configuration Syntax leave-all <port-list> <timer-value> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <timer-value>...
  • Page 136 EXAMPLE If you didn’t set the MRP environment already then the switch will show “Set leavetimer failed”. periodic To enable or disable periodic tx timer Syntax periodic <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable>...
  • Page 137 Syntax show <statistic> <port-list> Parameter <statistic> Show the basic MRP port statistics <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE...

  • Page 138: Mstp Of Cli

    MSTP of CLI Table : MSTP Commands Command Function CName Set MSTP Configuration name FwdDelay Set FwdDelay MaxAge Set Maxage MaxHops Set MaxHops Statistics Clear STP port statistics Txhold Set TxHold Version Set force-version bpduFilter Set edge port BPDU Filtering bpduGuard Set edge port BPDU Guard migrate-check...
  • Page 139 Syntax CName <word> Parameter <word> A text string up to 32 characters long. EXAMPLE FwdDelay To set the FewDelay parameter Syntax FwDelay <4-30> Parameter <4-30> MSTP forward delay (4-30, and max_age <= (forward_delay- 1)*2)). EXAMPLE MaxAge To set the STP Maximum age time. Syntax MaxAge <6-40>...
  • Page 140 MaxHops To set STP BPDU MaxHops parameter. Syntax MaxHops <6-40> Parameter <6-40> STP BPDU MaxHops (6-40)). EXAMPLE statistics To clear the selected port statistics Syntax statistics <clear> Parameter <clear> Clear the selected port statistics. EXAMPLE Txhold To set the STP Transmit Hold Count. Syntax Txhold <1-10>...
  • Page 142 version To set the force-version with STP/RSTP/MSTP Syntax version <mstp/ rstp/ stp> Parameter <mstp> Multiple Spanning Tree Protocol. <rstp> Rapid Spanning Tree Protocol. <stp> Spanning Tree Protocol EXAMPLE bpduFilter To set edge port BPDU filtering Syntax bpduFilter <disable/ enable> Parameter <disable>...
  • Page 144 migrate-check To set the STP mCheck (Migration Check) variable for ports Syntax migrate-check <port-list> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE msti-vlan To map Vlan ID(s) to an MSTI Syntax msti-valn <add/ delete> <instance no.> <VLAN ID> Parameter <add>...
  • Page 145 EXAMPLE p-bpduGuard To set the bpduGuard port parameter Syntax p-bpduGuard <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Disable port BPDU Guard. <enable> Enable port BPDU Guard. EXAMPLE p-cost To set the STP port instance path cost Syntax p-cost <0-7>...
  • Page 146 p-edge <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Configure MSTP adminEdge to Non-edge. <enable> Configure MSTP adminEdge to Edge. EXAMPLE p-mode To set the STP enabling for a port Syntax p-mode <port-list>...
  • Page 148 p-priority To set the STP port instance priority Syntax p-priority <0-7> <port-list> <0-240> Parameter <0-7> STP bridge instance no (0-7, CIST=0, MSTI1=1, ...). <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <0-240> STP bridge priority (0/16/32/48/.../224/240) EXAMPLE priority To set the bridge instance priority...
  • Page 149 EXAMPLE...
  • Page 150 r-tcn To set the MSTP restrictedTcn port parameter Syntax r-tcn <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5.. <disable> Disable MSTP restricted TCN. <enable> Enable MSTP restricted TCN.. EXAMPLE recovery To set edge port error recovery timeout Syntax recovery <time range>...
  • Page 152 Syntax show <Statistics> Parameter <Statistics> To show the STP port statistics. EXAMPLE Syntax show <Status> <0-7> Parameter <Status> To show the STP Bridge status. <0-7> STP bridge instance no (0-7, CIST=0, MSTI1=1 ...). EXAMPLE Syntax show <Instance> Parameter <Instance> To show the instance status. EXAMPLE...
  • Page 153 Syntax show <msti-vlan> Parameter <msti-vlan> To show the MSTP MSTI VLAN mapping configuration. EXAMPLE Syntax show <p-config> <0-7> Parameter <p-config> To show the STP port instance configuration. <0-7> STP bridge instance no (0-7, CIST=0, MSTI1=1 ...). EXAMPLE...
  • Page 154 Syntax show <pconf> Parameter <pconf> To show the STP Port configuration. EXAMPLE Syntax show <priority> Parameter <priority> To show the bridge instance priority. EXAMPLE...

  • Page 155: Mvr Of Cli

    MVR of CLI Table : MVR Commands Command Function immediate-leave Configure MVR port state about immediate leave mode Configure MVR mode port-mode Configure MVR port mode port-type Configure MVR port type show Show command immediate-leave To configure MVR port state about immediate leave. Syntax immediate-leave <port-list>...
  • Page 156 globally. <VLAN ID> Multicast VLAN ID, available is from 1 to 4094...
  • Page 157 EXAMPLE port-mode To configure the MVR port mode Syntax port-mode <port-list> <disable/enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Disable the MVR on the specific port. <enable> Enable the MVR on the specific port. EXAMPLE port-type To configure the MVR port type...
  • Page 158 show <config>...
  • Page 159 Parameter <config> To display the MVR configuration. EXAMPLE Syntax show <group> Parameter <group> To display the MVR group information. EXAMPLE If you didn’t set the MVR environment already then the switch won’t show any information. Syntax show <statistics> Parameter <statistics> To display the MVR statistics information. EXAMPLE...

  • Page 160: Mvrp Of Cli

    MVRP of CLI Table : MVRP Commands Command Function clear Clear the basic MVRP port statistics control Enable/Disable MVRP globally mode Enable/Disable MVRP on port rrole Enable/Disable MVRP restricted role on port show Show mvrp information clear To clear the basic MVRP port statistics Syntax clear <port-list>...
  • Page 162 mode To enable or disable MVRP function on port Syntax mode <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Disable the MVRP on port. <enable> Enable the MVRP on port. EXAMPLE rrole To enable or disable the MVRP restricted role on port.
  • Page 164 Syntax show <statistics> <port-list> Parameter <statistics> To display Show the basic MVRP port statistics.. <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE...

  • Page 165: Port Commands Of Cli

    Port Commands of CLI Table :Port Commands Command Function clear Clear port counter description Interface specific description excessive-collision Configure excessive collision operation flow-control Configure flow operation max-frame Configure maximum receive frame size port-state Configure port state operation power-saving Configure power saving operation show Show port information...
  • Page 166 Description <port-list><LINE> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <LINE> Up to 47 characters describing this interface EXAMPLE excessive-collision Configure excessive collision operation YNTAX excessive-collision <port-list> Discard Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- Discard Discard the packet when excessive collision restart Retransmit the packet, regardless of the number of collisions...
  • Page 167 EXAMPLE max-frame Configure maximum receive frame size YNTAX max-frame <port-list><1518-9600> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <1518-9600> Maximum receive frame size in bytes EXAMPLE port-state Configure port state operation YNTAX port-state <port-list> <disable><enable> Parameter <port-list>...
  • Page 168 power-saving <port-list>＜actiphy＞ Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- actiphy Enable ActiPHY power control disable Disable power saving dynamic Enable dynamic power control enable Enable power saving EXAMPLE show Show port information YNTAX Show Parameter configuration Show port configuration detail-counter Show detailed traffic statistics for specific switch port sfp Show sfp information...
  • Page 173 speed-duplex Configure speed duplex operation YNTAX speed-duplex <port-list>＜10-full＞ Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- 10-full Force speed duplex to 10-full operation 10-half Force speed duplex to 10-half operation 100-full Force speed duplex to 100-full operation 100-half Force speed duplex to 100-half operation 1000-full Force speed duplex to 1000-full operation auto Enable auto speed duplex configuration...

  • Page 174: Port-Security Commands Of Cli

    Port-Security Commands of CLI Table : Port-Security Commands Command Function show Show port security status show Show port security status YNTAX civic Parameter port Show MAC addresses learned by port security switch Show port security switch status EXAMPLE...

  • Page 175: Privilege Commands Of Cli

    Privilege Commands of CLI Table : Privilege Commands Command Function group Configure a privilege level group show Show privilege configuration group Configure a privilege level group YNTAX Group<group-name> Parameter <group-name> privilege group name EXAMPLE Show Show privilege configuration YNTAX show EXAMPLE...

  • Page 177: Pvlan Commands Of Cli

    PVLAN Commands of CLI Table : PVLAN Commands Command Function delete Delete private VLAN group port-isolate Configure port isolation private-vlan Configure private VLAN group show Show private VLAN information delete Delete private VLAN group YNTAX Delete＜ ＜ ＜ ＜ private-vlan＞＜ ＞＜1-10＞...
  • Page 178 private-vlan Configure private VLAN group YNTAX private-vlan <1-10><port-list> Parameter <1-10> Private VLAN ID, available value is from 1 to 10 <port-list> Port list, available value is from 1 to 10B format:1,3- EXAMPLE show Show private VLAN information YNTAX Show Parameter port-isolate Show port isolation information private-vlan...

  • Page 180: Qos Commands Of Cli

    QoS Commands of CLI Table :Qos Commands Command Function dscp-classification Configure DSCP ingress classification dscp-map Configure DSCP mapping table. This table is used to map QoS class and DP level based on DSCP value. DSCP value used to map QoS class and DPL is either translated DSCP value or incoming frame DSCP value...
  • Page 181 or incoming frame DSCP value if translation is disabled for the port. Trusted DSCP value is only used for QoS classification port-classify QoS ingress port classification port-dscp QoS port DSCP configuration port-scheduler QoS egress port schedulers port-shaper Port shaper Add or modify QoS control entry queue-shaper Queue shaper...
  • Page 182 used to map QoS class and DPL is either translated DSCP value or incoming frame DSCP value YNTAX dscp-map <dscp-list><0-7><0-1> Parameter <dscp-list> DSCP list, format : 1,3,5-7 <0-7> QoS class <0-1> Drop Precedence Level EXAMPLE dscp-remap Configure DSCP egress remap table. This table is used if the port egress remarking mode is 'remap' and the purpose is to map the DSCP and DP level to a new DSCP value...
  • Page 183 YNTAX dscp-remap <dscp-list><dpl-list><0-63> Parameter <dscp-list> DSCP list, format : 1,3,5-7 <dpl-list> Drop precedence level list, available value is from 0 to 1 <0-63> Egress remapped DSCP EXAMPLE dscp-translation Configure global ingress DSCP translation table. If port DSCP translation is enabled, translation table is used to translate incoming frame's DSCP value and translated value is used to map QoS class and DP level YNTAX...
  • Page 184 YNTAX dscp-trust <dscp-list>< disable > Parameter <dscp-list> DSCP list, format : 1,3,5-7 disable Set DSCP as untrusted DSCP enable Set DSCP as trusted DSCP EXAMPLE port-classify QoS ingress port classification YNTAX port-classify <port-list> <0-7> Parameter <port-list> Port list, available value is from 1 to 10B format:1,3- <0-7>...
  • Page 185 classification Configure DSCP classification based on QoS class and DP level. This enables per port to map new DSCP value based on QoS class and DP level egress-remark Configure the port DSCP remarking mode translation Configure DSCP ingress translation mode. If translation is enabled for a port, incoming frame DSCP value is translated and translated value is used for QoS classification <port-list>...
  • Page 186 port-shaper port-shaper YNTAX port-shaper <mode><port-list> <disable > Parameter mode Configure the port shaper mode rate Configure the port shaper rate <port-list> Port list, available value is from 1 to 10B format:1,3- disable Disable port shaper enable Enable port shaper EXAMPLE Add or modify QoS control entry YNTAX Qce <1-256><0-256>...
  • Page 187 classified-dscp Action of DSCP for this QCE dei Specify whether frames can hit the action according to DEI dmac Configure destination MAC address for this QCE dp Action of drop precedence level for this QCE dport Configure destination UDP/TCP port range for this ACE dscp Configure DSCP for this QCE end Finish QCE setting and return to QoS mode exit Exit from current mode...
  • Page 188 Parameter excess Configure the port queue excess bandwidth mode mode Configure the port queue shaper mode rate Configure the port queue shaper rate <port-list> Port list, available value is from 1 to 10B format:1,3- <queue-list> Queue list, available value is from 0 to 7 disable Disable use of excess bandwidth enable Enable use of excess bandwidth EXAMPLE...
  • Page 189 EXAMPLE...
  • Page 194 storm Configure storm rate control YNTAX storm <broadcast> <disable><enable> Parameter broadcast broadcast storm control multicast multicast storm control unicast unicast storm control disable Disable broadcast storm control enable Enable broadcast storm control EXAMPLE...
  • Page 195 tag-remarking QoS egress port tag remarking YNTAX tag-remarking <disable><enable> Configure the default DEI. This value is used when port tag remarking mode is set to 'default' map Configure the port tag remarking map. This map is used when port tag remarking mode is set to 'mapped', and the purpose is to translate the classified QoS class (0-7) and DP level (0-1) to PCP and DEI mode Configure the port tag remarking mode...

  • Page 196: Smtp Of Cli

    SMTP of CLI Table : SMTP Commands Command Function delete Delete command level Configure Severity level mail-address Configure email-address description return-path Configure email return-path description sender Configure email sender description server Configure email server description show Show email configuration username Configure email user name level To configure Severity level and parameter.
  • Page 198 mail-address To configure the email address alias for identified the email property. Syntax mail-address <Email address index> <mail-address description> Parameter <Email address index> Email address index, the available value is from 1 to 6. <mail-address description> Up to 47 characters describing mail address. EXAMPLE return-path To configure the email return-path description.
  • Page 200 sender To configure the email sender identified the alarm mail sender. Syntax sender <sender description> Parameter < sender description > Up to 47 characters describing sender. EXAMPLE server To configure the email server description. Syntax server <server description> Parameter < server description > Up to 47 characters describing email server. EXAMPLE...
  • Page 201 show To show the email server configuration and information. Syntax show Parameter none. EXAMPLE username To configure email user name. Syntax username <username account> <password> Parameter < username account > Up to 47 characters describing user name. < password> Up to 47 characters describing password EXAMPLE...

  • Page 202: Snmp Of Cli

    SNMP of CLI Table : SNMP Commands Command Function access Configure SNMP access community Configure SNMP community delete Delete command engine-id Set SNMP Engine ID group Configure SNMP groups mode Enable/Disable SNMP mode show Show SNMP command trap Configure SNMP trap user Configure SNMP users view...
  • Page 203 reserved for Empty. (Range: 1-32 characters, ASCII characters 33-126 only). < write_view name> he scope for a specified instance can write, None is reserved for Empty. (Range: 1-32 characters, ASCII characters 33-126 only) EXAMPLE community To configure SNMP community, the command adds the SNMP community mapping to security name entry.
  • Page 204 < view > Delete snmpv3 views entry < table index> The SNMP entry table index, the available value is from 1 to 4. EXAMPLE engine-id To configure the SNMP Engine ID, the command sets the SNMPv3 local engine ID. Syntax engine-id <HEX>...
  • Page 205 group To configure SNMP group, the command adds an SNMPv3 group entry. Syntax group <user name> <security model> <group name> Parameter < user name > The name of user connecting to the SNMP agent. (Range: 1-32 characters, ASCII characters 33-126 only). <...
  • Page 206 EXAMPLE show To show the SNMP configuration or detail information. Syntax show <access /community /group/ mode/ trap/ user/ view> Parameter <access> Show snmpv3 access entry. <community> Show snmpv3 community entry. <group> Show snmpv3 groups entry. <mode> Show snmp configuration. <trap> Show snmp trap entry. <user>...
  • Page 207 <trap port> To set the trap port, the available value is from 1 to 65535. <severity level> To configure the Severity level, the available value is from 0 to <0> Emergency: system is unusable. <1> Alert: action must be taken immediately. <2>...
  • Page 208 Syntax user <user name> <security level> <Authentication Protocol> <Authentication Password> Parameter <username> The name of user connecting to the SNMP agent, (Range: 1-32 characters, ASCII characters 33-126 only). <security level> The security level assigned to the user, (NoauthNoPriv | AuthNoPriv | AuthPriv) <...
  • Page 209 The view oid-subtree first character must be a period (.). Wild cards can be used to mask a specific portion of the OID string using an asterisk. (Length: 1-128)

  • Page 210: Ssh Of Cli

    SSH of CLI Table : SSH Commands Command Function mode Configure the SSH mode show Show SSH configuration mode To configure the SSH mode. Syntax mode <disable/ enable> Parameter <disable> Disable SSH mode operation. <enable> Enable SSH mode operation. EXAMPLE show To show the SSH configuration.
  • Page 211 Syntax show Parameter none. EXAMPLE...

  • Page 212: Syslog Of Cli

    SYSLOG of CLI Table : SYSLOG Commands Command Function clear Clear syslog entry level Configure syslog level mode Configure syslog mode server Configure syslog server IP address show Show SSH configuration clear To clear the syslog entry. Syntax clear Parameter none.
  • Page 213 <2> Critical: critical conditions. <3> Error: error conditions. <4> Warning: warning conditions. <5> Notice: normal but significant condition. <6> Informational: informational messages. <7> Debug: debug-level messages. EXAMPLE mode To configure syslog mode with enable or disable. Syntax mode <disable/ enable> Parameter <disable>...
  • Page 214 EXAMPLE...
  • Page 215 show To show syslog information. Syntax show <config/ detail-log/ log> Parameter <config> Show syslog configuration. <detail-log> Show detailed syslog information. <log> Show syslog entry EXAMPLE...

  • Page 216: System Of Cli

    SYSTEM of CLI Table : SYSTEM Commands Command Function contact Configure system contact description Configure system description location Configure system location name Configure device name show Show system information contact To configure the system contact information. Syntax contact <system contact information> Parameter <system contact information>...
  • Page 218 description To configure system description that descripts the device property. Syntax description <system description> Parameter <system description > Up to 255 characters describing system information. EXAMPLE location To configure the system location. Syntax location <system location> Parameter <system location> Up to 256 characters describing system location. EXAMPLE...
  • Page 220 name To configure device name or alias. Syntax name <system name> Parameter <system name> Up to 255 characters describing device name. EXAMPLE...
  • Page 221 show To show the system detail information. Syntax show Parameter none. EXAMPLE...

  • Page 222: Thermal Of Cli

    THERMAL of CLI Table : THERMAL Commands Command Function port-priority Configure the port priority Configure the temperature at which the ports shall be shut priority-temp down show Show thermal protection information port-priority To configure the port priority. Syntax port-priority <port-list> <port priority> Parameter <port-list>...
  • Page 224 show To show the thermal protection information. Syntax show Parameter none. EXAMPLE...

  • Page 225: Time Of Cli

    TIME of CLI Table : TIME Commands Command Function daylight Indicates the Daylight Savings operation delete Delete NTP server entry manual Configure system time manually Configure system time by NTP show Show time information time-zone Configure system time zone daylight To indicates the Daylight Savings operation.
  • Page 227 delete To delete NTP server entry. Syntax delete <NTP server index> Parameter <NTP server index> NTP server index, available value is from 1 to 5. EXAMPLE manual To configure system time manually. Syntax manual <date of system> <time of system> Parameter <date of system>...
  • Page 229 To configure system time by NTP. Syntax ntp <mode> <disable/ enable> Parameter <mode> Indicates the NTP mode operation. <disable> Disable NTP mode operation. <enable> Enable NTP mode operation. EXAMPLE Syntax ntp <server> <server index> <ipv6-address/ ip-hostname> Parameter <server> Indicates the NTP mode operation. <server index>...
  • Page 230 show To show time information. Syntax show <daylight/ ntp> Parameter <daylight> Show the daylight time information. <ntp> Show the NTP information. EXAMPLE...

  • Page 231: Vcl Of Cli

    VCL of CLI Table : VCL Commands Command Function delete Delete command mac-vlan Configure MAC-based VLAN membership protocol-vlan Configure protocol-based VLAN show Show VCL status command delete To delete the configured command or VCL rule entry. Syntax delete < mac-vlan> <mac-address> Parameter <mac-vlan>...
  • Page 232 <ethernet> Delete protocol-based VLAN Ethernet-II protocol to group mapping. <ether type> Ether type, available value is from 0x0600 to 0xffff. EXAMPLE Syntax delete < protocol-vlan> <llc> <DSAP value> <SSAP value> Parameter <protocol-vlan> Delete protocol-based VLAN. <llc> Delete protocol-based VLAN LLC protocol to group mapping. <DSAP value>...
  • Page 233 EXAMPLE mac-vlan To configure MAC-based VLAN membership. Syntax mac-address mac-vlan < > <vlan ID> <port-list> Parameter <mac-address> MAC address, format 0a-1b-2c-3d-4e-5f. <vlan ID> VLAN ID, available value is from 1 to 4094. <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE protocol-vlan To configure protocol-based VLAN.
  • Page 234 EXAMPLE Syntax protocol-vlan <protocol > <llc> <DSAP value> <SSAP value> <protocol-based vlan name> Parameter <protocol> Protocol-based VLAN ethertype protocol to group mapping. <llc> Protocol-based VLAN LLC protocol to group mapping. <DSAP value> DSAP value, available value is from 0x00 to 0xff. <SSAP value>...
  • Page 235 EXAMPLE Syntax protocol-vlan <vlan> <protocol-based vlan name><vlan ID> <port-list> Parameter <vlan> Protocol-based VLAN group to VLAN mapping. <protocol-based vlan name> Up to 16 characters to describe protocol-based VLAN group name. <vlan ID> VLAN ID, available value is from 1 to 4094. <port-list>...
  • Page 236 EXAMPLE Syntax show <protocol- vlan> Parameter <protocol- vlan > Show protocol-based VLAN configuration. EXAMPLE...

  • Page 237: Vlan Of Cli

    VLAN of CLI Table : VLAN Commands Command Function delete Delete VLAN group egress-rule Configure egress-rule of switch ports frame-type Configure frame type of switch ports ingress-filtering Configure ingress filtering of switch ports port-type Configure port type of switch ports pvid Configure port VLAN ID show...
  • Page 238 egress-rule To configure egress-rule of switch ports Syntax egress-rule <port-list> <access/ hybric/ trunk> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <access> Untag all frames. <hybric> Tag all frames except VLAN ID same as PVID. <trunk>...
  • Page 240 ingress-filtering To configure ingress filtering of switch ports Syntax ingress-filtering <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Disable ingress filtering. <enable> Enable ingress filtering. If ingress port is not a member of the classified VLAN of the frame, the frame is discarded.
  • Page 241 <s-port> To set the port as the service port type. <unaware> To set the port as the VLAN unaware port type.
  • Page 242 EXAMPLE pvid To configure the Port VLAN ID Syntax pvid <port-list> <VLAN ID> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <VLAN ID> VLAN ID, available value is from 1 to 4094. EXAMPLE show To show the VLAN configuration and information. Syntax...
  • Page 243 show <port-config> Parameter <port-config> Show VLAN port configuration. EXAMPLE Syntax show <port-status> <combined/ gvrp/ mstp/ mvr/ mvrp/ nas/ static/ voice> Parameter <port-status> Show VLAN port status <combined> VLAN port status for combined VLAN Users. <gvrp> VLAN port status for GVRP. <mstp>...
  • Page 245 tag-group To configure tag-based VLAN group. Syntax tag-group <VLAN ID> <VLAN Name> <port-list> Parameter <VLAN ID> VLAN ID, available value is from 1 to 4094. <VLAN Name> Up to 32 characters describing VLAN name. <port-list> Port list, available value is from 1 to 14 format: 1,3-5. EXAMPLE tpid To configure the TPID used for Custom S-ports.

  • Page 246: Voice-Vlan Of Cli

    VOICE-VLAN of CLI Table : VOICE-VLAN Commands Command Function config Configure Voice VLAN delete Delete command discovery Configure Voice VLAN discovery protocol Create Voice VLAN OUI entry. Modify OUI table will restart auto detect OUI process port-mode Configure Voice VLAN port mode security Configure Voice VLAN port security mode show...
  • Page 247 delete To delete the Voice VLAN OUI entry. Modify OUI table will restart auto detect OUI process. Syntax delete <oui> <oui-address> Parameter <oui> Delete Voice VLAN OUI entry. Modify OUI table will restart auto detect OUI process. <oui-address> OUI address, format : 0a-1b-2c. EXAMPLE If you didn’t set Voice VLAN OUI already then the switch will show “ERROR! Voice VLAN table entry not exist”.
  • Page 248 To create Voice VLAN OUI entry. Modify OUI table will restart auto detect OUI process. Syntax oui <oui-address> <LINE> Parameter <oui-address> OUI address, format : 0a-1b-2c. <LINE> Up to 32 characters describing OUI address. EXAMPLE port-mode To configure Voice VLAN port mode. Syntax port-mode <port-list>...
  • Page 249 security <port-list> <disable/ enable> Parameter <port-list> Port list, available value is from 1 to 14 format: 1,3-5. <disable> Disjoin from Voice VLAN. <enable> Enable Voice VLAN security mode. When the function is enabled, all non-telephone MAC address in Voice VLAN will be blocked 10 seconds. EXAMPLE show To show the Voice VLAN configuration and information.

Table of Contents