Aac Installation - Paradyne WIRELESS DATA GATEWAY Installation And Operation Manual

AAC Installation and Configuration

AAC Installation

Mount the AAC Chassis
Install the Power Supply
Install the Plug-In Module
Install WAN Card
Install the E&M Card
Install CPU Card
Install the Interface Card
Install the Alarm Card
Mount the 50-Pin to RJ48C Adapter
Connect the E&M Cards to the NIMs
Connect the Adapter to the Interface Card
Connect the Control Terminal to the Interface Card
Connect the Adapter to the Mobile Switch
AAC Installation
Install the AAC and its components using the
procedures described in the ACCULINK Access
Controller Reference Guide. Note the following additions
to those procedures.
1. Prior to installing the 4-wire E&M cards in the
AAC, set these cards for E&M Type V signaling
using the procedure in the ACCULINK Access
Controller Reference Guide.
2. Install the six E&M cards in user slots U1 through
U6. Do not populate slots U7 and U8.
3. Configure the cards as shown in this chapter.
Configure the AAC using a VT100-compatible
terminal attached to the TERM port on the AAC,
following the instructions in the ACCULINK Access
Controller Reference Guide.
Experienced installers may wish to follow this
checklist.
3981-A2-GN31-20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
November 1996
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checklist
Mount the AAC chassis in the cabinet.
Install the – 48 Vdc power supply.
Install the DSX/CEPT or CSU plug-in module.
Install the WAN card.
Install the 4-Wire E&M cards.
Install the CPU card.
Install the Interface card.
Install the Alarm card (if any).
Mount the 50-pin Amphenol to RJ48C adapter.
Connect the E&M cards to the NIMs.
Connect the Interface card to the adapter.
Connect the Interface card to the control terminal.
Connect the adapter to the switch.
5
5-1
5-2
5-2
5-2
5-3
5-3
5-7
5-7
5-7
5-8
5-9
5-10
5-10
5-10
5-1