1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Gateway
  5. 1862
  6. User manual

Paradyne 1862 User Manual

Voip iad (mgcp)
Hide thumbs Also See for 1862:
Table of Contents

Advertisement

Quick Links

Download this manual
1862 VoIP IAD (MGCP)
User's Guide
Document Number 1862-A2-GB20-00
November 2004

Advertisement

Table of Contents
loading

Related Manuals for Paradyne 1862

Summary of Contents for Paradyne 1862

  • Page 1 1862 VoIP IAD (MGCP) User’s Guide Document Number 1862-A2-GB20-00 November 2004...
  • Page 2 When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals → CE Declarations of Conformity. 1862 VoIP IAD User’s Guide...
  • Page 3 1862 VoIP IAD User’s Guide Preface This manual is written for Web management. It is designed to provide information to network administrators. It covers the installation, operation and applications of the VoIP IAD (Integrated Access Device). Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual.
  • Page 4 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 1862 VoIP IAD User’s Guide...
  • Page 5 1862 VoIP IAD User’s Guide • Consult the dealer or an experienced radio/TV technician for help. Notice to Users of the United States Telephone Network The following notice applies to versions of the modem that have been FCC Part 68 approved.
  • Page 6 1862 VoIP IAD User’s Guide Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met.

  • Page 7: Table Of Contents

    1862 VoIP IAD User’s Guide Table of Contents CHAPTER 1 INTRODUCTION...9 RODUCT VERVIEW ...10 EATURES LED I RONT ANEL CHAPTER 2 HARDWARE INSTALLATION ...13 ARDWARE INSTALLATION USB D NSTALLING THE NINSTALLING THE FXO ...18 CHAPTER 3 LOGGING IN TO THE WEB INTERFACE...19 IP A ...19...
  • Page 8 1862 VoIP IAD User’s Guide...

  • Page 9: Chapter 1 Introduction

    IAD, allowing calls to be routed to anywhere in the world — significantly reducing or eliminating long distance charges. Your PCs do not need to be turned on to make calls. The 1862 VOIP IAD supports policy-based QoS on Layer 3, which provides high quality voice service.

  • Page 10: Features

    Configurable Through Your Networked PC’s Web Browser Remote Administration and Remote Firmware Upgrades Over the Internet Block Specific External and Internal Internet Access with Packet Filtering Supports PPTP, L2TP and IpSec Pass-Through Supports Lifeline POTS for Emergencies 1862 VoIP IAD User’s Guide...

  • Page 11: Front Panel Led Indicators

    1862 VoIP IAD User’s Guide Front Panel LED Indicators LED Indicator Color Green Power Green Green ADSL Green ALARM Green Green Green Green Green Mode Function Power is supplied. Power is not supplied. An Ethernet link is established. An Ethernet link is not established.
  • Page 12 1862 VoIP IAD User’s Guide Green Flashing Activity over the USB link.

  • Page 13: Chapter 2 Hardware Installation

    1862 VoIP IAD User’s Guide Chapter 2 Hardware Installation Hardware installation The figure below illustrates possible connections to the back panel of the 1862 VOIP IAD. Caution: Always disconnect all telephone lines from the telephone wall-outlet before servicing or disassembling this device.

  • Page 14: Installing The Usb Driver

    IMPORTANT: Make sure your IAD is disconnected before installing the software. To install the USB driver complete the following steps: STEP 1: Insert the CD-ROM disc for the 1862 VoIP IAD. STEP 2: Browse the CD-ROM and open the USB Driver Folder Double-click on on SETUP.EXE:...
  • Page 15 1862 VoIP IAD User’s Guide STEP 4: An installation successful message pops up when the installation is complete. STEP 5: Connect your IAD to the USB port of the PC...

  • Page 16: Uninstalling The Usb Driver

    1862 VoIP IAD User’s Guide Uninstalling the USB Driver If it for some reason becomes necessary, you can uninstall the USB driver by completing the following steps: STEP 1: Click on the Windows Start button and go to Programs>Drivers Comtrend CT-6xx.
  • Page 17 1862 VoIP IAD User’s Guide STEP 4: When the driver is removed, a complete message pops up. Click on Finish to close the window.

  • Page 18: Fxo

    1862 VoIP IAD User’s Guide Selected models support FXO and a France-compliant built-in splitter. The default Mode is VoIP; it means the telephone (FXS) will connect to VoIP when you pick-up the phone. In the meantime you can press ‘# #’ to connect to FXO.

  • Page 19: Chapter 3 Logging In To The Web Interface

    1862 VoIP IAD User’s Guide Chapter 3 Logging In to the Web Interface This section describes how to manage the IAD via a Web browser from the remote end. You can use a web browser such as Microsoft Internet Explorer 6.0 or above. Use a browser that provides full support for JavaScript.

  • Page 20: Login Procedure

    The default user name is root, and password 1234. The user name and password are case-sensitive. Note: The user name and password may be different for different service providers; please contact your service provider for details. 1862 VoIP IAD User’s Guide...
  • Page 21 1862 VoIP IAD User’s Guide STEP 4: After successfully logging in, you will reach the main menu. On this framed window, a menu of hyperlinks is displayed on the left. There are three categories: • Basic • VoIP • Advanced...

  • Page 22: Chapter 4 Mgcp

    1862 VoIP IAD User’s Guide Chapter 4 MGCP MGCP Configuration The MGCP option is used to verify the MGCP application configured by you. We will use the scenario illustrated in the following diagram to explain MGCP configuration: STEP 1: Select MGCP on the VoIP menu; the current configuration of the IAD is displayed.
  • Page 23 1862 VoIP IAD User’s Guide STEP 3: Enter the MGCP Gateway and Call Agent information for your Service provider. The fields are explained below. • Gateway Domain Name: The domain name of the Gateway. For example, mg1. Port Number: The gateway port number for MGCP Call Signaling control. For example, 2427.
  • Page 24 DOWN: If you choose “DOWN”, the Gateway will send a RSIP *@[Gateway Name] with “Graceful” method for this endpoint to the call agent. Payload Types: The Endpoint associated Codec list STEP 4: Click on the Apply button to update the configuration. 1862 VoIP IAD User’s Guide...

  • Page 25: Chapter 5 Basic Configuration

    1862 VoIP IAD User’s Guide Chapter 5 Basic Configuration From the Basic menu you can set up a list of users, configure the WAN/LAN interfaces, set up routing, save settings, reboot the device, and retrieve the factory default settings. Access Control To manage the List of Users, click on on Access Control on the menu bar.
  • Page 26 STEP 4: Click on Apply to submit the settings. • User Name: This field displays the selected user name. • Authorization Old: This field displays the previous authorization services for the specific user account. • Authorization: Authorization for CLI, HTTP or FTP services. 1862 VoIP IAD User’s Guide...

  • Page 27: Delete User

    1862 VoIP IAD User’s Guide • Permissions: Select Ordinary or Administration user permission. 5.1.4 Delete User To delete a User from the list of users, complete the following steps: STEP 1: Click on Access Control on the menu bar. STEP 2: Choose a User entry, and click on on Delete.

  • Page 28: Wan Setup

    • Enable DHCP: Enables (if checked) or disables the DHCP server. The DHCP server dynamically allocates network addresses and delivers configuration parameters to hosts. DHCP or Dynamic Host Configuration Protocol is explained further in section 6.2. This feature is available for RFC 1483 Routed, PPPoE, PPPoA, and MER. 1862 VoIP IAD User’s Guide...

  • Page 29: Rfc 1483 Bridged

    1862 VoIP IAD User’s Guide 5.2.1 RFC 1483 Bridged When you use RFC 1483 style bridging, Ethernet frames are bridged over ATM Virtual Circuits. The Ethernet frames are encapsulated using either LLC Encapsulation or VC Multiplexing. With LLC encapsulation, a link control header is added to the Ethernet packet that identifies the protocol type (Ethernet).

  • Page 30: Rfc 1483 Routed

    1862 VoIP IAD User’s Guide 5.2.2 RFC 1483 Routed To set up the RFC 1483 Routed mode, configure the common settings on the top of the page, click on on RFC 1483 Routed and configure the specific settings (WAN IP address and WAN...
  • Page 31 1862 VoIP IAD User’s Guide 5.2.3 PPPoE PPPoE provides session authentication using either Password Authentication Protocol (PAP) or Challenge Handshake Authentication Protocol (CHAP). Session accounting is possible and conservation of bandwidth can be achieved by closing down unused sessions. By utilizing PPP, link and network parameters are easily negotiated between the IAD/Router and the ISP.
  • Page 32 Click on the Add button to add the entry. User name and Password: used for remote customers to login upon dialup. PPPoA is manually activated by entering startup commands from the page: Advanced> Configure> PPPoA. Authentication: defines the authentication code (PAP or CHAP). 1862 VoIP IAD User’s Guide...
  • Page 33 1862 VoIP IAD User’s Guide 5.2.5 MAC Encapsulation Routing (MER) lets the IAD route IP addresses on the RFC 1483 bridged link. NAPT function is supported to allow multiple private IP addresses on the LAN to share a public IP address.
  • Page 34 Secondary DNS server: Enter the secondary server IP address that will be used in the event that the primary server IP address fails or is not available Default Gateway: The gateway IP address of the IP network STEP 4: Submit the settings by clicking on Apply. 1862 VoIP IAD User’s Guide...

  • Page 35: Lan Ip Address

    1862 VoIP IAD User’s Guide LAN IP Address The default LAN IP address is 192.168.1.1. Click on LAN Setup on the menu bar to configure the LAN IP address. Type the LAN IP address and subnet mask. Click on Apply to submit the settings.

  • Page 36: Routing

    1862 VoIP IAD User’s Guide Routing Click on Routing Setup on the menu bar to configure the routing functions. Routing functions include RIP and static routing. You can display the RIP information by clicking on the RIP information button. If you wish to change the static routes that are configured you must first...

  • Page 37: Enable Rip

    1862 VoIP IAD User’s Guide 5.4.1 Enable RIP To enable RIP, complete the following steps: STEP 1: Click on Routing Setup on the menu bar. STEP 2: Select On in the Rip Status field. STEP 3: Select a RIP Version (Version 1 or Version 2) from the Version field.

  • Page 38: Static Route Configuration

    1862 VoIP IAD User’s Guide 5.4.2 Static route configuration The Routes Configuration field allows you to add, modify, and delete a static route. Type the Destination Network ID, subnet mask and Next hop IP, and click on on a button below to perform the requested function.

  • Page 39: Save

    1862 VoIP IAD User’s Guide Save To save the settings to Flash, click on on Save & Reboot on the menu bar. In the main window, click on on Save. Reboot To reboot the IAD, click on on Save & Reboot on the menu bar. In the main window, click on...

  • Page 40: Retrieve Default Settings

    1862 VoIP IAD User’s Guide Retrieve default settings To retrieve the default settings, click on on Erase & Reboot on the menu bar. In the main window, click on on Erase.

  • Page 41: Chapter 6 Advanced Configuration

    1862 VoIP IAD User’s Guide Chapter 6 Advanced Configuration Configure From the Interface Configure page, you can configure LAN and WAN interfaces, VCC, PPPoE, PPPoA, DNS & Default Gateway, and NAT.

  • Page 42: Configure Interface

    MAC address. Others display N/A. Status: UP and Down. When an interface is set to Down, the system will not attempt to transmit messages through that interface. When set to UP, messages can be transmitted through the interface. 1862 VoIP IAD User’s Guide...
  • Page 43 1862 VoIP IAD User’s Guide The following is displayed when you select eth0 and click on the Configure Interface button. 6.1.2 DNS & Default Gateway: To configure the DNS and default gateway, complete the following steps: STEP 1: Click on Interface Configure in the menu bar.

  • Page 44: Vcc

    1862 VoIP IAD User’s Guide Default Gateway: The gateway IP address of the IP network. STEP 4: Submit the settings by clicking on Apply. This screen lists all current VCC entries in the middle of the screen. From this screen you can also: List IPoA, Delete Encapsulation, Add a VCC, Delete a VCC, and Show VCC quality.

  • Page 45: Delete Encapsulation

    1862 VoIP IAD User’s Guide 6.2.2 Delete Encapsulation To delete encapsulation first select a VCC entry and then click on on the Delete Encap button. 6.2.3 Add a VCC To add a VCC entry, complete the following steps: STEP 1: Click on the Add VCC button; the VCC screen will appear.
  • Page 46 Rate characteristics. Ubr – Unspecified Best effort service that does not require tightly constrained Bit Rate delay and delay variation. UBR provides no specific quality of service or guaranteed throughput. 1862 VoIP IAD User’s Guide...

  • Page 47: Delete A Vcc

    1862 VoIP IAD User’s Guide 6.2.4 Delete a VCC To delete a VCC entry, select the entry from the list of VCCs and then click on on the Delete button, at the bottom-right of the page. 6.2.5 Show VCC quality To view information regarding the VCC quality, click on on the Show VCC Quality button, at the bottom-right of the page.
  • Page 48 The PPPoA page can be accessed by clicking on Configure in the Advanced menu bar. To start, stop, delete, or set as default a PPPoA entry, first select the entry from the List of PPPoA entries, and then click on on the corresponding button at the bottom of the page. 1862 VoIP IAD User’s Guide...

  • Page 49: Adsl Mode

    1862 VoIP IAD User’s Guide ADSL Mode There are four ADSL modes: MULTI, ANSI, G.DMT, and G.LITE. The default ADSL mode is ANSI. MULTI mode enables the device to auto-adjust its mode to match the remote Central Office (CO) DSL Access Multiplexer (DSLAM). You can specify an ADSL mode on this page, and click on on the Apply button to submit the settings.
  • Page 50 Secondary DNS: The secondary IP address of the Domain Name Server Lease Time (in Days): Upon login, the remote workstation will obtain an IP address. This field defines the period of time that the workstation can use this IP address to access the Internet. 1862 VoIP IAD User’s Guide...
  • Page 51 1862 VoIP IAD User’s Guide 6.4.3 Disable DHCP Server To stop a DHCP Server, complete the following steps: STEP 1: Click on DHCP on the menu bar. STEP 2: Choose a DHCP entry, and click on on Stop. 6.4.4 Delete DHCP Server To delete a DHCP Server, complete the following steps: STEP 1: Click on DHCP on the menu bar.

  • Page 52: Dhcp Relay

    Disable the BOOTP/DHCP Relay To disable the BOOTP/DHCP Relay complete the following steps: STEP 1: Access the BOOTP/DHCP Relay screen by clicking on DHCP on the Advanced Menu, and then click on on the BOOTP/DHCP Relay tab. 1862 VoIP IAD User’s Guide...

  • Page 53: Dhcp Relay Nat

    1862 VoIP IAD User’s Guide STEP 2: In the DHCP Relay field, select Disable, and enter the IP Address where you want BOOT REQUEST or DHCP packets to be received from clients. STEP 3: Click on the Apply button. The NAPT port redirect page is used to set up the virtual server. A virtual server has two access ports: public and private.
  • Page 54 1862 VoIP IAD User’s Guide...

  • Page 55: Chapter 7 Performance Monitoring

    1862 VoIP IAD User’s Guide Chapter 7 Performance Monitoring ADSL Link Status To view the ADSL link status, click on on Link Status from the tool bar. The page includes the following information: Field Description ADSL Line Status Shows the current status of the ADSL line ADSL Mode Shows the ADSL standard that is currently configured.

  • Page 56: System Statistics

    The number of Octets (bytes) received Unicast PktsIn The number of unicast packets received Broadcast PktsIn The number of broadcast packets received Discards In The number of packets received that were discarded Errors In The number of inward errors 1862 VoIP IAD User’s Guide...
  • Page 57 1862 VoIP IAD User’s Guide Field Description Octets Out The number of Octets (bytes) transmitted Unicast PktsOut The number of unicast packets transmitted Broadcast PktsOut The number of broadcast packets transmitted Discards Out The number of packets transmitted that were discarded...
  • Page 58 1862 VoIP IAD User’s Guide 7.2.2 TCP/IP To view TCP/IP statistics click on on the TCP-IP tab at the top of the System Statistics page. The TCP-IP page displays the IP statistics, UDP statistics, TCP statistics, and ICMP statistics.

  • Page 59: Atm Statistics

    1862 VoIP IAD User’s Guide 7.2.3 DHCP-Lease To view DHCP-Lease statistics click on on the DHCP-Lease tab at the top of the System Statistics page. The DHCP-Lease page shows the PCs that obtained an IP address from the DHCP pool.
  • Page 60 1862 VoIP IAD User’s Guide 7.3.2 Encapsulation Click on the SNDCP tab to display encapsulation statistics. This page displays the VCs that are running. SNDCP stands for sub-network dependency convergency protocol.

  • Page 61: Chapter 8 Diagnostics

    1862 VoIP IAD User’s Guide Chapter 8 Diagnostics To access the Diagnostics screen, click on the Diagnostics button, which is located on the menu bar. The Diagnostics screen has two test functions: OAM Loopback and Ping test. OAM Loopback STEP 1: Click on the Diagnostics button, on the menu bar.

  • Page 62: Ping

    Minimum round trip time: Maximum round trip time: The number of packets that were transmitted The number of packets that were received The number of packets lost The fastest round-trip time The slowest round-trip time 1862 VoIP IAD User’s Guide...

  • Page 63: Chapter 9 Software Upgrade Via Ftp

    1862 VoIP IAD User’s Guide Chapter 9 Software Upgrade via FTP Follow the steps below to upgrade the firmware version of the IAD via FTP. The procedures below will use LAN port IP address 192.168.1.1 for illustration. STEP 1: Connect the IAD to a PC using the LAN cable. Set the PC to the same subnet as the IAD (192.168.1.1).
  • Page 64 1862 VoIP IAD User’s Guide STEP 9: After a moment, the file should begin transferring, after you see the message Transfer complete, the upgrade process is complete.

  • Page 65: Chapter 10 Specifications

    1862 VoIP IAD User’s Guide Chapter 10 Specifications WAN Interface ADSL Standard Data rate Downstream: Up to 11 Mbps Upstream: LAN Interface Ethernet Standard Standard Analog Interface FXS x 1 FXO x 1(Built-in Microfilter) ATM Attributes RFC 2364, RFC 2684 (RFC 1483) Bridge; RFC 2684 (RFC 1483) Route; RFC 2516; RFC 1577...
  • Page 66 8.1 in (W) x 1.9 in (H) x 5.7 in (D) PAP, CHAP PPTP/L2TP/IpSec pass-through RFC 3261 RFC 3435 H.323 v3 G.711,G.723.1,G.729ab RFC 1889 RFC 2327 ETSI based G.168 G.711,G.723.1,G.729ab 110 Vac or 220 Vac 0 – 50 degrees Celsius 5 – 90% (non-condensing) 1862 VoIP IAD User’s Guide...

  • Page 67: Chapter 11 Pin Assignments

    1862 VoIP IAD User’s Guide Chapter 11 Pin Assignments ADSL Port (RJ11) Pin number FXS port (RJ11) Pin number LAN Port (RJ45) Pin number Definition Pin number ADSL_RING Definition Pin number RING Definition Pin number Transmit data + Transmit data –...

  • Page 68: Chapter 12 Troubleshooting

    POWER LED is not lit Check the power adapter and verify if it meets the requirement as stated in Appendix A, Specifications. Power connections are loose or improperly connected. Power source is off. 1862 VoIP IAD User’s Guide...

  • Page 69: Chapter 13 Glossary

    1862 VoIP IAD User’s Guide Chapter 13 Glossary 100BaseT: A 100 Mbps Ethernet standard that uses twisted-pair wiring. 10BaseT A 10 Mbps Ethernet standard that uses twisted-pair wiring. address: The symbol (usually numeric) identifying an interface attached to a network.
  • Page 70 +10 volts and –10 volts. These states are then represented by the binary digits 0 and 1. digital: loopback test: A test that connects the device’s receiver output back to the transmitter input. This test will disrupt the transmission of primary data. 1862 VoIP IAD User’s Guide...
  • Page 71 1862 VoIP IAD User’s Guide DLL: Dynamic Link Library. DLLs are files that are automatically loaded into memory when required. DMT: Discrete MultiTone. The T1.413 standard modulation scheme for Digital Subscriber Line technology. DNS: Domain Name Server. A server that retains the addresses and routing information for TCP/IP PAT users.
  • Page 72 Internet Service Provider. An organization that provides access to the Internet. ITU: International Telecommunications Union. The telecommunications agency of the United Nations. kbps: Literally it means Kilobits per second, but usually it is taken to mean 1,024 bits per second. 1862 VoIP IAD User’s Guide...
  • Page 73 1862 VoIP IAD User’s Guide LAN: Local Area Network. A LAN is a data communications system that lies within a limited spatial area, has a specific user group, and has a specific topology. latency: The time it takes a signal to transmit from its source to its destination.
  • Page 74 Provides a list of items available on other servers to increase the availability and speed of retrieving that information. Any connection with only two endpoints. A dedicated data link 1862 VoIP IAD User’s Guide...
  • Page 75 1862 VoIP IAD User’s Guide PSTN: Public Switched Telephone Network. The standard telephone network. PVC: Permanent Virtual Circuit. Virtual circuit that is permanently established. QoS: Quality of Service. The expected data loss or latency. remote access: ommunication from a remote location or facility through a data link.
  • Page 76 Universal Serial Bus. A bi-directional, isochronous, serial interface for adding dynamically connectable peripheral devices, without the need for a reboot. UTP: Unshielded twisted pair is the most common kind of copper telephone wiring. Transmission with the transmitter and receiver synchronized so 1862 VoIP IAD User’s Guide...
  • Page 77 1862 VoIP IAD User’s Guide Virtual Circuit. A logical connection or packet-switching mechanism established between two devices at the start of transmission. VCI: Virtual Channel Identifier. The 16-bit field in an ATM cell header that specifies the virtual channel over which the cell is to be transmitted.
  • Page 78 1862 VoIP IAD User’s Guide...

Table of Contents