53-1002977-01 30 September 2013 Brocade FCX Series Hardware Installation Guide Supporting FastIron Software Release 08.0.01...
Page 2
ServerIron, VCS, VDX, and Vyatta are registered trademarks, and HyperEdge, The Effortless Network, and The On-Demand Data Center are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of their respective owners.
Attaching a PC or terminal................49 Wiring map for serial cable..............50 Installing and replacing a power supply unit........... 50 Installing or replacing fan trays............... 52 Installing an optional module ................53 Optional 2-port 10 Gbps SFP+ uplink module........55 Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 4
Power cords..................92 AC power supply specifications............93 Troubleshooting ........................95 Diagnosing switch indicators ................95 Power and cooling problems.............95 Installation..................95 In-band access..................95 Regulatory Statements......................97 USA (FCC CFR 47 Part 15 Warning)............97 Industry Canada statement................97 Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 5
Europe and Australia (CISPR 22 Class A Warning)........98 Germany (Noise Warning)................98 Japan (VCCI)....................98 Japan power cord....................98 Korea.......................99 China......................100 BSMI statement (Taiwan)................100 Regulatory compliance..................101 Cautions and Danger Notices....................103 Cautions......................103 Danger notices....................107 Index............................ 111 Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 6
Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Identifies command names, keywords, and command options. italic text Identifies a variable. value In Fibre Channel products, a fixed value provided as input to a command option is printed in plain text, for example, --show WWN Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 8
DANGER A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety labels are also attached directly to products to warn of these conditions or situations Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Asia Pacific: +800-AT • Knowledge Base • Environment description FIBREE (+800 28 34 27 33) • For areas unable to access toll free number: +1-408-333-6061 • Toll-free numbers are available in many countries. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
By sending your feedback to documentation@brocade.com. Provide the publication title, part number, and as much detail as possible, including the topic heading and page number if applicable, as well as your suggestions for improvement. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
(works as Combo port) or four-port 10 Gbps SFP+ module. On the rear panel a removable fan tray provides a cooling airflow from the front to the rear of the device. Two rear-panel power supply receptacles accommodate up to two power supply units that also support a front-to-rear cooling airflow. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 14
Specifications" section. The following figures show the front panels of the FastIron CX models. For more information about Combo ports, see Network interfaces for Brocade FCX 624-E, FCX 624-I, FCX 648-E, and FCX 648-I Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 15
FIGURE 4 Brocade FCX 624S-HPOE front panel FIGURE 5 Brocade FCX 648S-HPOE front panel FIGURE 6 Brocade FCX 648S-HPOE rear panel FIGURE 7 Brocade FCX 624-E front panel FIGURE 8 Brocade FCX 624-I front panel Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 16
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or an orange arrow with an "I". Device Label on required power supply Label on required fan tray Brocade FCX 624-E and Brocade FCX 648-E Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Brocade recommends that you refer to Cable specifications before connecting a cable to any of the ports. Network interfaces for Brocade FCX 624-E, FCX 624-I, FCX 648-E, and FCX 648-I FastIron CX devices contain the following interfaces: Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 18
SFP module for SFP support. Slot locations There are three slot locations on Brocade FCX Series devices: slots 3 and 1 on the front panel and slot 2 on the rear panel. FIGURE 12 Slot locations on the front panel of Brocade FCX Series devices...
Page 19
Product Overview Slot 3 Slot 1 FIGURE 13 Slot location on the rear panel of Brocade FCX Series devices Slot 2 (default stacking ports) Slot designations The slot designations for FCX models: TABLE 2 Stack unit slots for FCX stackable devices...
Page 20
The Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S-HPOE, and FCX 648S-HPOE devices include a slot on the front panel for a two-port 10 Gbps XFP uplink module. This module operates at 10 Gbps full duplex. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 21
Gbps SFP+ module, and connecting devices using standard duplex LC cables. These devices cannot be combined in a stack with non-FCX devices. For detailed information about how to configure FCX devices in a homogeneous stack, see the FastIron Ethernet Switch Stacking Configuration Guide . Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 22
The two left ports on the SFP+ module do not pass regular Ethernet traffic by default. The stack disable CLI command must be configured on these two ports in order for them to pass regular traffic. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 23
The module is named FCX-2SFPP 2-port 10G Module (2-SFP+) in configuration and output. NOTE Reload the device whenever you install or replace the module because the 2x10 SFP+ module is not hot swappable. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 24
10 Gbps SFP+ module port status LEDs Condition Status Link or Act LED (Link or On or flashing green Port has a valid link at 10 Gbps. Activity Flashing indicates activity. The port is down. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 25
The following is sample output of the show running-config command. device# show running-config Startup-config data location is flash memory Startup configuration: ver 07.3.00a001T7f1 stack unit 1 module 1 fcx-48-poe-port-management-module module 2 fcx-cx4-2-port-16g-module module 3 fcx-sfpp-2-port-10g-module Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 26
1/1/40:C 1/1/41:C 1/1/42:C 1/1/43:C 1/1/44:C 1/1/45:C 1/1/46:C 1/1/47:C 1/1/48:C 1/2/1:XG-CX4 1/2/2:XG-CX4 1/3/1:XG-ER 1/3/2:XG-USR Specifying a port address You can specify a port address for a data port, stacking port, or a management port. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 27
FCX switches include a display panel for key system and port indicators that simplifies installation and network troubleshooting. The LEDs are located on the front panel for easy viewing. FIGURE 18 Port status LEDs Port status LEDs Port status LEDs Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 28
A link is not established with a remote port. FIGURE 19 System status LEDs System status LEDs TABLE 9 System status LEDs Condition Status Green Power supply is operating normally. Amber Power supply fault. (Power Supply Status) Power off or failure. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 29
FIGURE 20 Power status LEDs Power status LEDs TABLE 10 Power status LEDs Condition Status DC OK Green DC output ok DC output fail AC OK Green AC input ok AC input fail Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 30
The LED will turn to green automatically once the load is increased over the minimum load requirement. In configurations with a single power supply installed the "DC OK" LED will light green in a no-load or light-load condition. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 31
A link is not established with a remote port. SFP+(1F~4F) On/Flashing Green The SFP+ port has established a valid 10 Gbps link. Flashing indicates the port is transmitting and receiving user packets. Link or Activity Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 32
On/Flashing Green The port has established a valid link at 10/100/1000 Activity Mbps. Flashing indicates the port is transmitting and receiving user packets. A link is not established with a remote port. FIGURE 23 Power status LEDs Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 33
AC OK Green Off Running DC OK Green Off ‘DC OK’ LEDs Red and Off AC OK Green Off Failure DC OK Red All ‘AC OK’ LEDs Off AC OK Off Power Off or Failure Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Brocade FCX 624S-HPOE and Brocade FCX 648S-HPOE devices use a 620W PSU. When one PSU is powering the switch, the HPOE budget is 410W. If both PSUs are installed and powering the switch, each PSU provides 410W to the switch, increasing the HPOE budget to 820W. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
49. General requirements To manage the system, you need a management station, such as a PC running a terminal emulation application. Connect the management station to the Console serial port on the switch. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Continue configuring the device using the CLI. You can also Brocade Network Advisor use Brocade Network Advisor to manage the device. Secure access to the device. FastIron Ethernet Swich Secuity Guide Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Use a separate branch circuit for each AC power cord, which provides redundancy in case one of the circuits fails. CAUTION To avoid high voltage shock, do not open the device while the power is on. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Maintain temperatures within 0 to 40 ο C (32 to 104 ο F) and humidity levels within 5% to 95%, non-condensing. • Allow a minimum of 3 in. of space between the sides and the back of the device and walls or other obstructions for proper air flow. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
If installing a single switch only, refer to Powering on the system on page 48. If installing multiple switches, attach the adhesive feet to each one. Place each device squarely on top of the one below, in any order. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Use the following setps to mount devices in rack. Remove the rack mount kit from the shipping carton. The kit contains two L-shaped mounting brackets and mounting screws. Attach the mounting brackets to the sides of the device. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 41
FCX624-E, FCX624-I, FCX648-E, and FCX648-I device brackets are mounted using three screws. FIGURE 26 Attaching the brackets for the Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S-HPOE, and FCX 648S-HPOE devices FIGURE 27 Attaching the brackets for the FCX624-E, FCX624-I, FCX648-E, and FCX648-Idevices Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 42
Installing the FCX Switch Brocade FCX Series Hardware Installation Guide 53-1002977-01...
If installing multiple switches, mount them in the rack, one below the other, in any order. Connecting devices in a traditional stack Brocade FCX Series devices can operate as standalone devices and also as members of traditional stacks. A stack is a group of devices--Brocade stackable units and their connected stacking links--that are connected so that the stack is managed as a single entity.
Page 44
10 Gbps SFP+ module on the front panel. Refer to the table below for the list of supported XFP transceivers (for stacking and non-stacking FCX models) and supported SFP and SFP+ transceivers. TABLE 17 Stacking ports on Brocade FCX Series devices Stacking ports Data ports Panel/slot...
Page 45
Installing the FCX Switch TABLE 17 Stacking ports on Brocade FCX Series devices Stacking ports Data ports Panel/slot Ports Default Can be data Default data Can be stacking ports stacking ports 4-port 10 Front/2 Yes: 1, 2 Yes: 3, 4...
For information about configuring a stack, see the FastIron Ethernet Switch Stacking Configuration Guide. Stacking cables To connect Brocade FCX Series devices in a stack, you need to use specific cables. TABLE 19 Cables used to connect Brocade FCX Series devices...
Page 47
In ring stack topology, there is an extra connection between the logical first and last devices forming a"ring" or "closed-loop." The closed-loop connection provides a redundant path for the stack link, so if one link fails, stack communications can be maintained. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 48
4, and unit 4 connects to unit 1. FIGURE 32 FCX S devices in linear (top) and ring (bottom) stacking topologies FIGURE 33 FCX E devices in a linear stacking topology Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 49
Installing the FCX Switch FIGURE 34 FCX E devices in a ring stacking topology FIGURE 35 FCX S (top) and FCX E devices (bottom two devices) in a linear stacking topology Brocade FCX Series Hardware Installation Guide 53-1002977-01...
To turn the system off, simply unplug the power cable or cables. NOTE The socket should be installed near the equipment and should be easily accessible. NOTE If the outlet is not rated 115/120V, stop and get the appropriate cable for the outlet. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
DB-9 or DB-25 connector, male or female. For more information about serial cable options between a Brocade device and a PC or terminal, see Wiring map for serial cable. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Before opening the package that contains the PSU, touch the bag to the switch casing to discharge any potential static electricity. Brocade recommends using an ESD wrist strap during installation. Remove the PSU from the anti-static shielded bag. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 53
PSU is correctly installed and supplying power. CAUTION If you do not install a PSU in a slot, you must keep the slot panel in place. If you run the device with an uncovered slot, the system will overheat. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Before opening the package that contains the new fan tray, touch the bag to the switch casing to discharge any potential static electricity. It is recommended that you wear an ESD wrist strap during installation. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
The fans are controlled by software, and their speed is set according to the environmental temperature surrounding the switch. Installing an optional module FIGURE 40 Installing an optional module on Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S- HPOE, and FCX 648S-HPOE devices Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 56
Remove the module from the anti-static shielded bag. Holding the module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
The module is named FCX-2SFPP 2-port 10G Module (2-SFP+) in configuration and output. NOTE Reload the device whenever you install or replace the module because the 2x10 SFP+ module is not hot swappable. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 58
10 Gbps SFP+ module port status LEDs Condition Status Link or Act LED (Link or On or flashing green Port has a valid link at 10 Gbps. Activity Flashing indicates activity. The port is down. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 59
The following is sample output of the show running-config command. device# show running-config Startup-config data location is flash memory Startup configuration: ver 07.3.00a001T7f1 stack unit 1 module 1 fcx-48-poe-port-management-module module 2 fcx-cx4-2-port-16g-module module 3 fcx-sfpp-2-port-10g-module Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Port Configuration - Allows read-and-write access for specific ports but not for global (system- wide) parameters. • Read Only - Allows access to the Privileged EXEC mode and CONFIG mode but only with read access. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Enter no password at the prompt. (You cannot abbreviate this command.) Enter boot system flash primary at the prompt. This command causes the device to bypass the system password check. After the console prompt reappears, assign a new password. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
10.22.3.1 NOTE You do not need to assign a default gateway address for single subnet networks. Syntax: enable [ password ] Syntax: configure terminal Syntax: [no] ip address ip-addr ip-mask Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Syntax: [no] ip address ip-addr ip-mask [ secondary ] Syntax: [no] ip address ip-addr/mask-bits [ secondary ] Use the secondary parameter if you have already configured an IP address within the same subnet on the interface. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 65
Loopback interfaces are always up, regardless of the states of physical interfaces. They can add stability to the network because they are not subject to route flap problems that can occur due to Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 66
1 as the routing interface for the VLAN. The last two commands change to the interface configuration level for the virtual interface and assign an IP address to the interface. Syntax: router-interface ve num Syntax: interface ve num Brocade FCX Series Hardware Installation Guide 53-1002977-01...
NOTE The 802.3ab standard (automatic MDI or MDIX detection) calls for automatic negotiation of the connection between two 1000Base-T ports. In this case a straight-through cable may work just as well Brocade FCX Series Hardware Installation Guide 53-1002977-01...
(NICs). Fiber cabling is required for direct attachment to Gigabit NICs or switches and routers through fiber ports. Refer to Connecting a network device to a fiber port on page 67. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
10km 10GBase-ER 40km 10GBase-LRM (1310-MMF) 200m 10G-ZR 80km 10GBase-ZRD 80km TABLE 23 Supported SFP transceivers for FCX624-E, FCX624-I, FCX648-E, and FCX648-I devices 10 Gigabit Optic Distance Supported for stacking 10GSFPP-SR 300m 10GSFPP-LR 10km Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 70
NOTE For safety reasons, the ESD wrist strap should contain a series 1 meg ohm resistor. CAUTION All fiber optic interfaces use Class 1 lasers. Use the following setps to install a transceiver. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 71
FIGURE 45 Installing a transceiver into FCX-624S, FCX-648S, FCX-624S, FCX-624S-HPOE, and FCX-648S-HPOE devices FIGURE 46 Installing a transceiver into Brocade FCX 624-E, FCX 624-I, FCX 648-E, and FCX 648- I devices Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 72
To clean the fiber cable connectors, Brocade recommends using a fiber optic reel-type cleaner. You can purchase this type of cleaner from the following Website: http://www.fisfiber.com/Home_Page.asp When not using an SFP connector, make sure to keep the protective covering in place. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
For the combination ports (ports 1~4), check that the shared SFP port (1F~4F) is not being used. • If the other actions don’t resolve the problem, try using a different port or a different cable. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 74
Check the Link LED to make sure the link is port. still established with the remote port. If not, take the actions described in the Meaning or Action column for the Link LED. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
The CLI displays trace route information for each hop as soon as the information is received. Traceroute requests display all responses to a given TTL. In addition, if there are multiple equal-cost routes to the destination, the Brocade device displays up to two responses by default. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Viewing the results of the cable analysis To display the results of the cable analysis, enter a command similar to the following at the Privileged EXEC level of the CLI. device# show cable-diag tdr 1/1/1 Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Console messages and syslog messages are sent when optical operating conditions fall below or rise above the XFP, SFP, and SFP+ manufacturer’s recommended thresholds. For more information about digital optical monitoring, refer to FastIron Ethernet Switch Administration Guide. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 78
Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Power supply 2 not present Fan ok, speed (auto): [[1]]<->2<->3 Fan speed switching temperature thresholds: 1 -> 2 @ 61 deg-C 1 <- 2 @ 56 deg-C 2 -> 3 @ 67 deg-C Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 80
Syntax: temperature warning stack-id value The stack-id can be 1 - 8. The value can be 0 - 125 device# temperature temperature temperature sensor commands device# temperature warning warning Temperature at which the module sends a warning Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 81
Power supply 2 not present Fan ok, speed (auto): [[1]]<->2<->3 Fan speed switching temperature thresholds: 1 -> 2 @ 61 deg-C 1 <- 2 @ 56 deg-C 2 -> 3 @ 67 deg-C Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Removing MAC address entries You can remove the following types of learned MAC address entries from the system MAC address table: • All MAC address entries • All MAC address entries for a specified Ethernet port Brocade FCX Series Hardware Installation Guide 53-1002977-01...
This section provides information about the following tasks: • Removing a copper or fiber optic module • Installing a new copper or fiber optic module • Cabling a fiber optic module Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Bail Latch FIGURE 47 Unlocking the bail latch NOTE The bail latch may be attached to either the top or the bottom of the mini-GBIC. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
For instructions on cabling a fiber optic module refer to Cabling a fiber optic transceiver. Cleaning the fiber optic connectors For instructions on cleaning a fiber optic module refer to Cleaning the fiber optic connectors. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 86
Brocade FCX Series Hardware Installation Guide 53-1002977-01...
For the Brocade FCX 624-I and Brocade FCX 648-I models, the air flows from the rear to the front of the device. • Total cooling capacity: 180 Watts • Total air flow: 85.2 CFM • Operating noise: ideal 60 dB-A NOTE Operating noise is based on the ISO 7779 standard. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 89
"E", or an orange arrow with an "I". FIGURE 49 Brocade FCX 624S, FCX 648S, FCX 624S-F, FCX 624S-HPOE, and FCX 648S-HPOE device airflow Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 90
Hardware Specifications Air inflow Air outlet FIGURE 50 Brocade FCX 624-E and Brocade FCX 648-E device airflow Brocade FCX Series Hardware Installation Guide 53-1002977-01...
FIGURE 51 Brocade FCX 624-I and Brocade FCX 648-I device airflow Air inflow Air outlet For a complete list of regulatory compliances refer to Regulatory compliance. Pinouts and signalling This section describes the pinout diagrams for the DB-9 connector and RJ45 port jacks. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 92
Some of the wires should not be connected. If you do connect the wires that are labeled "Reserved", you may get unexpected results with some terminals. FIGURE 53 Console port pin assignments showing cable connection options to a terminal or PC Brocade FCX Series Hardware Installation Guide 53-1002977-01...
10G SFP+ TWNX 1, 3, and 5 Power cords All devices ship with US-compatible power cords unless otherwise specified at the time of order. United Kingdom- and European-compatible power cords are also available. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
In-band access You can access the management agent in the switch from anywhere within the attached network using Telnet, a Web browser, or other network management software. However, you must first configure the Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 98
IP address. Also, be sure the port through which you are connecting to the switch has not been disabled. If it has not been disabled, then check the network cabling that runs between your remote location and the switch. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Industry Canada statement Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. English translation of above statement This Class A digital apparatus complies with Canadian ICES-003. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Japan power cord Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Class A device (Broadcasting Communication Device for Office Use): This device obtained EMC registration for office use (Class A), and may be used in places other than home. Sellers and/or users need to take note of this. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
AS or NZS CISPR 22, Electromagnetic Compatibility Immunity: • EN 61000-6-1, Electromagnetic Compatibility, Generic Standard • EN 55024, Information Technology equipment - Immunity Characteristics Safety: • BI-NAT CSA 60950-1-07/UL 60950-1 Second Edition • EN 60950-1:2006 • IEC 60950-1:2005 Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 104
Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Use a separate branch circuit for each AC power cord, which provides redundancy in case one of the circuits fails. VORSICHT Es empfiehlt sich die Installation eines separaten Stromkreiszweiges für jede Wechselstrom- Elektroschnur als Redundanz im Fall des Ausfalls eines Stromkreises. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 106
Si vous effacez la configuration par accident sur un système configuré, entrez write memory la commande pour enregistrer la configuration actuelle dans le fichier startup-config. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 107
MISE EN GARDE Risque d'explosion en cas de remplacement de la pile par un modèle incorrect. Débarrassez-vous des piles usagées conformément aux instructions. PRECAUCIÓN Riesgo de explosión si se sustituye la batería por una de tipo incorrecto. Deshágase de las baterías usadas de acuerdo con las instrucciones. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 108
électriques à la terre. MISE EN GARDE Bevor Sie ein Kabel in einen Anschluss einstecken, entladen Sie jegliche im Kabel vorhandene elektrische Spannung, indem Sie mit den elektrischen Kontakten eine geerdete Oberfläche berühren. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
GEFAHR Alle Glasfaser-Schnittstellen verwenden Laser der Klasse 1. DANGER Toutes les interfaces en fibres optiques utilisent des lasers de classe 1. PELIGRO Todas las interfaces de fibra óptica utilizan láser de clase 1. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 110
Cette marque vous assure que vous pouvez utiliser le cordon d'alimentation avec le dispositif en toute sécurité. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 111
DANGER Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga ohm. PELIGRO Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de 1 mega ohmio. Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 112
Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Page 114
Serial Port Pinouts Syslog temperature System unpacking Temperature displaying poll interval sensor changing warning and shutdown levels Syslog troubleshooting in-band access power and cooling problems Troubleshooting network connections Unpacking a System Uplink port Brocade FCX Series Hardware Installation Guide 53-1002977-01...
Need help?
Do you have a question about the FCX Series and is the answer not in the manual?
Questions and answers