Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-6400HDI-T
Summary of Contents for HIKVISION DS-6400HDI-T
- Page 1 HD Video/Audio Decoder User Manual (V2.2.0) UD.6L0203D1036A01...
- Page 2 The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book.
- Page 3 User Manual of DS-6400HDI-T Decoder Regulatory information FCC information compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 User Manual of DS-6400HDI-T Decoder Preventive and Cautionary Tips Before connecting and operating your decoder, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Keep all liquids away from the decoder.
-
Page 5: Table Of Contents
User Manual of DS-6400HDI-T Decoder Table of Contents CHAPTER 1 Introduction ......................6 1.1 Description ........................7 1.2 Features ........................... 7 CHAPTER 2 Panels and Connections ..................9 2.1 Front Panel ........................10 2.2 Rear Panel ........................10 CHAPTER 3 Initial Network Parameters Configuration ............11 3.1 Searching Active Devices Online ................ - Page 6 User Manual of DS-6400HDI-T Decoder 4.2.8 Managing User Account ..................33 4.2.9 Importing/Exporting Parameters ................34 4.3 Configuring Remote Playback ..................34 4.4 Rebooting, Upgrading and Restoring the Default Settings for the Decoder ....35 CHAPTER 5 Decoder Configuration and Operation by Client Software ....... 38 5.1 Adding an Encoder ......................
-
Page 7: Chapter 1 Introduction
User Manual of DS-6400HDI-T Decoder CHAPTER 1 Introduction... -
Page 8: Description
TI platform, Linux operating system and Netra processor, ensuring high reliability and stability of system running. DS-6400HDI-T Series HD Video/Audio Decoder is capable of decoding video at 5MP resolution and outputting decoded video via BNC, VGA and HDMI interfaces, and it also supports multiple network protocols and multiple stream transmission mode. - Page 9 User Manual of DS-6400HDI-T Decoder directly obtain the record files from the encoder, and finally decode for local output. Network One 10/100/1000Mbps self-adaptive Ethernet interface. Support TCP, UDP and Multicast network protocols. Multiple DDNS settings: Peanut Hull, Dyndns, IPServer, NO-IP and HiDDNS.
-
Page 10: Chapter 2 Panels And Connections
User Manual of DS-6400HDI-T Decoder CHAPTER 2 Panels and Connections... -
Page 11: Front Panel
User Manual of DS-6400HDI-T Decoder 2.1 Front Panel Figure 2.1 Front Panel Table 2.1 Description of Front Panel LED Indicator & Interface Connections POWER Power LED indicator LINK Network connection LED indicator Tx/Rx Data transmitting/receiving status LED indicator 2.2 Rear Panel Figure 2.2 Rear Panel of DS-6408HDI-T... -
Page 12: Chapter 3 Initial Network Parameters Configuration
User Manual of DS-6400HDI-T Decoder CHAPTER 3 Initial Network Parameters Configuration... -
Page 13: Searching Active Devices Online
This chapter aims to tell the procedures of using the SADP software to find and configure the IP address and other parameters of the device. Note: For the first-time user, the default user name of DS-6400HDI-T is admin, and password is 12345. And the default IP address is 192.0.0.64. 3.1 Searching Active Devices Online ... -
Page 14: Modifying Network Parameters
User Manual of DS-6400HDI-T Decoder Search online devices manually You can also click to refresh the online device list manually. The newly searched devices will be added to the list. Note: You can click on each column heading to order the information; you can click... -
Page 15: Chapter 4 Decoder Configuration And Operation By Web Browser
User Manual of DS-6400HDI-T Decoder CHAPTER 4 Decoder Configuration and Operation by Web Browser... -
Page 16: Decoding Operation
User Manual of DS-6400HDI-T Decoder Purpose: Since there is no local operation GUI provided for the decoder, you can manage and configure it by web browser or the iVMS-4200 client software. In this chapter, the operation and management of the decoder by the web browser is provided. - Page 17 In the display control interface, you can configure the Display Channel, Video Format (BNC), BNC Output Scaling (BNC), Output Resolution (VGA, HDMI) and Display Mode. Figure 4.4 Configure Display Parameters Select the window-division display mode. The DS-6400HDI-T series supports 1/4/9/16-division display mode. Select the decoding channel from the drop-down list for each sub-window.
-
Page 18: Configuring Dynamic Decoding
User Manual of DS-6400HDI-T Decoder Steps: Select the button to enlarge the selected sub-window and display in full-screen mode. The following prompt will pop up: Figure 4.6 Enlarge the Sub-window Click OK to enlarge the selected sub-window, and the Window Enlarged in the Sub-window Configuration... - Page 19 Set the IP address of the stream media server. port1: Set the port No. of the stream media server. It is 554 be default if you do not configure it. hikvision: The identifier of the Hikvision SMS (stream media server) 4.0.
-
Page 20: Configuring Cycle Decoding
User Manual of DS-6400HDI-T Decoder ip2: Enter the IP address of the encoding device to be decoded. port2: Enter the port No. of the encoding device to be decoded. chan: Enter the channel No. of the encoding device for decoding. -
Page 21: Configuring Video Wall Display
User Manual of DS-6400HDI-T Decoder Note: Refer to Chapter 4.1.2 for configuring the input stream assigned to the cycle decoding channel. Figure 4.11 Edit Cycle Decoding of a Channel Click OK to save the settings and back to the Cycle Decoding interface, or click Back to back to the Cycle Decoding interface without saving. - Page 22 User Manual of DS-6400HDI-T Decoder Figure 4.13 Configure Video Wall Select the Screen No. from the drop-down list. Select the Screen Jointing Mode. Different modes are selectable based on models: DS-6404HDI-T: 1*2, 2*1, 2*2. DS-6408HDI-T: 1*2, 2*1, 2*2, 2*3, 3*2, 2*4 and 4*2.
-
Page 23: Enabling/Disabling The Decoding Channel
User Manual of DS-6400HDI-T Decoder 4.1.5 Enabling/Disabling the Decoding Channel Purpose: The Channel On/Off function enables you to start or stop the decoding and displaying for certain channels. Steps: Click Decode Operation > Decode Control > Channel On/Off to enter the following interface: Figure 4.15 Configure Channel On/Off... -
Page 24: Checking The Connection Status
User Manual of DS-6400HDI-T Decoder Note: The picture must be in 24-bit BMP format and its width and height must be 32X pixel, with up to 128×128 resolution and 24 bits depth. You can check the checkbox of Flash to set the display style of the picture. -
Page 25: Checking The Display Channel Status
User Manual of DS-6400HDI-T Decoder Figure 4.18 Check Decoding Channel Status 4.1.9 Checking the Display Channel Status Purpose: The display channel status interface shows the video output status of the decoder, including the status for the VGA output, BNC output, HDMI output, and the sub-window information. - Page 26 User Manual of DS-6400HDI-T Decoder Steps: Click Decode Operation > Transparent Channel to enter the Transparent Channel settings interface. Click to select a transparent channel from the list to configure. Figure 4.20 Configure Transparent Channel Select the Local Serial Port and the Remote Serial Port to RS-485 or RS-232.
-
Page 27: Decoder Configuration
User Manual of DS-6400HDI-T Decoder 4.2 Decoder Configuration 4.2.1 Checking Device Information Purpose: You can check the information of the device in the device information interface, such as the Device Type, Device Serial No., Firmware Version, etc. Steps: Click Configuration > Device Information to view the device information, including the Device Type, Device Serial No., Firmware Version, DSP Version, etc. -
Page 28: Configuring Basic Network Settings
User Manual of DS-6400HDI-T Decoder date/time. If the device is connected to a Dynamic Host Configuration Protocol (DHCP) network that has time server properties configured, the camera will synchronize automatically with the time server. Enable the NTP function by checking the checkbox, and configure the following settings: NTP Server: IP address of NTP server. -
Page 29: Configuring Ddns Settings
User Manual of DS-6400HDI-T Decoder Figure 4.26 Configure Basic Network Settings Set the network parameters, including the IP Address, Subnet Mask, Gateway and DNS Server. Click Save to save the settings. 4.2.4 Configuring DDNS Settings Purpose: If your device is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used for network access. - Page 30 User Manual of DS-6400HDI-T Decoder Figure 4.28 DynDNS Settings • IPServer: (1) Enter Server Address for IPServer. (2) Click Save to save the settings. Note: For the IP Server, You have to apply a static IP, subnet mask, gateway and primary DNS from the ISP.
-
Page 31: Configuring Rs-485/Rs-232 Serial Port
User Manual of DS-6400HDI-T Decoder Figure 4.30 PeanutHull Settings • HiDDNS: (1) Enter the Server Address of the HiDDNS server: www.hik-online.com. (2) Enter the Domain Name of the device. You can register the alias of the device domain name in the HiDDNS server first and then enter the alias to the domain name in the decoder;... -
Page 32: Configuring Alarm Input / Output Settings
User Manual of DS-6400HDI-T Decoder Figure 4.32 Configure RS-232 Settings Configure the RS-232 parameters, including the baud rate, data bit, stop bit and parity type. Select the Operating Mode of RS-232 to Console or Transparent Channel. Console: use the RS-232 serial port for debugging the decoder. -
Page 33: Configuring Arming Time
User Manual of DS-6400HDI-T Decoder Steps: Alarm Input Settings Click Configuration > Alarm Settings > Alarm Input to enter the alarm setting interface. Set the Alarm Sensor Type for the selected alarm input and configure the Alarm Input Handling actions. -
Page 34: Managing User Account
User Manual of DS-6400HDI-T Decoder Figure 4.36 Configure Arming Time Choose the Start Time and the End Time. Click Save to save the schedule. 4.2.8 Managing User Account The user accounts can be managed in this interface. Steps: Click Configuration > User Management to enter the account management interface. -
Page 35: Importing/Exporting Parameters
User Manual of DS-6400HDI-T Decoder 4.2.9 Importing/Exporting Parameters The configuration files of the device can be imported from or exported to local device for backup, which maintains convenient and easy parameters configuration. Steps: Click Configuration > Config File Import/Export to enter the parameters import/export interface: Figure 4.38 Import/Export Config File... -
Page 36: Rebooting, Upgrading And Restoring The Default Settings For The Decoder
User Manual of DS-6400HDI-T Decoder Select a Decoding Channel from the drop-down list for playback. Enter the device information in the Remote Host IP Address, Remote Host Port, Remote Host Channel No., and login User Name and Password of the encoding device. - Page 37 User Manual of DS-6400HDI-T Decoder Steps: To reboot, upgrade or restore the default settings of the decoder, go to the Device Management interface. Choose the configuration items in the left part of the page. To upgrade the decoder: Click the icon to enter the interface, see the following figure.
- Page 38 User Manual of DS-6400HDI-T Decoder To reboot the decoder: Click icon to enter the rebooting interface. Click OK if you are sure to reboot the device. Figure 4.45 Reboot the Device...
-
Page 39: Chapter 5 Decoder Configuration And Operation By Client Software
User Manual of DS-6400HDI-T Decoder CHAPTER 5 Decoder Configuration and Operation by Client Software... -
Page 40: Adding An Encoder
User Manual of DS-6400HDI-T Decoder Run the disk of iVMS-4200 software, and double click the icon to install it in your PC. In this chapter, the basic procedure of operating the decoder by the software is described. Please refer to the user manual of iVMS-4200 for more detailed information. - Page 41 User Manual of DS-6400HDI-T Decoder Figure 5.2 Add Device by IP Address Task2: Add the device by IP server or HiDDNS. Check the checkbox of Edit the nickname of the encoding device. Select the DDNS type to IP Server or HiDDNS by checking the checkbox.
- Page 42 User Manual of DS-6400HDI-T Decoder Figure 5.4 Add Third-party Device Note: The added third-party encoding device is only a virtual node, and the live view and parameters configuration cannot be realized via the iVMS-4200 client software. You can check the successfully added device on the Device Management interface.
-
Page 43: Adding A Decoder
User Manual of DS-6400HDI-T Decoder 5.2 Adding a Decoder Steps: Click in the control panel to enter the decoding device management interface. Click to add the decoder to the management list of the software. Enter the Nickname, IP address and port number of the device, and input the user name and password to get access to it. -
Page 44: Setting Tv Wall Layout
User Manual of DS-6400HDI-T Decoder Figure 5.9 List of Added Decoders You can also click Show online devices to add the decoder. Please refer to Section 0 Adding an Encoder for operating instructions. 5.3 Setting TV Wall Layout Steps: In the control panel, click to enter the TV Wall setting interface. - Page 45 User Manual of DS-6400HDI-T Decoder Figure 5.11 Screen Configuration Interface Click and drag the channels on the list of the decoding devices to the display screens. Figure 5.12 Configure Screen Layout You can double click a decode channel on the list to modify its nickname and video standard (BNC) or resolution...
-
Page 46: Decoding Operation
User Manual of DS-6400HDI-T Decoder Figure 5.13 Modify Output Information 5.4 Decoding Operation Steps: In the control panel, click to enter the TV Wall interface. Figure 5.14 TV Wall Interface In this configuration interface, the left bar lists the encoding devices which has been added to the client software, and the bottom bar with the configuration of the decoding action. -
Page 47: Configuring Remote Setting For The Decoder
User Manual of DS-6400HDI-T Decoder Stop decoding Start cycle decoding Stop cycle decoding Click and drag the encoding channels from the left list to the screen on the TV Wall. Select the screen and click the button on the bottom or select Start Decoding from the right-click menu to start decoding. - Page 48 User Manual of DS-6400HDI-T Decoder Figure 5.17 Remote Settings of the Decoder Note: The RS-485 parameters of the decoder cannot be configured through the remote settings. For detailed information, please refer to the User Manual of the iVMS-4200 Client Software.
-
Page 49: Chapter 6 Appendix
User Manual of DS-6400HDI-T Decoder CHAPTER 6 Appendix... -
Page 50: Appendix A. Specifications
User Manual of DS-6400HDI-T Decoder Appendix A. Specifications Model DS-6401HDI-T DS-6404HDI-T DS-6408HDI-T 1-ch 4-ch 8-ch VGA Output 1920×1080@60/50Hz, 1600×1200@60Hz, 1280×1024@60Hz, 1280×720@50/60Hz, 1024×768@60Hz 1-ch 4-ch 8-ch Audio/ HDMI Output 1920×1080@60/50HZ, 1600×1200@60Hz, Video Output 1280×1024@60Hz, 1280×720@50/60Hz, 1024×768@60Hz CVBS Output 1-ch 2-ch 4-ch... -
Page 51: Appendix B. Faq
User Manual of DS-6400HDI-T Decoder Appendix B. FAQ Why cannot ping the decoder? Check the cable and the switch. Please refer to Chapter 3 to configure the IP address of the decoder. Why cannot connect the decoder with client software? Check the decoder IP address. -
Page 52: Appendix C. List Of Third-Party Ip Cameras Access
User Manual of DS-6400HDI-T Decoder Appendix C. List of Third-party IP Cameras Access IP Camera Model Manufacturer Supported Video Format SP306H Panasonic SP336H SNC-CH220 Sony SNC-RH124 P5532 Axis Q7404 H.264, MPEG4 VCC-HD2500P Sanyo Bosch NBC265P D5110 Zavio Arecont AC1305M IX30DN-ACFZHB3...