Summary of Contents for HIKVISION DS-6700HUHI-K Series
Page 1
DS-6700HUHI-K Series Encoder User Manual UD07058B...
Page 2
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Page 3
DS-6700HUHI-K Series Encoder User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 4
DS-6700HUHI-K Series Encoder User Manual Applicable Models This manual is applicable to the models listed in the following table. Series Model DS-6704HUHI-K DS-6700HUHI-K DS-6708HUHI-K DS-6716HUHI-K Symbol Conventions The symbols that may be found in this document are defined as follows.
Page 5
DS-6700HUHI-K Series Encoder User Manual Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Unit is designed for indoor use only.
DS-6700HUHI-K Series Encoder User Manual Product Key Features General Self-adaptive HDTVI/HDCVI/AHD/CVBS signal input Connectable to the Coaxitron camera/dome with long transmission distance 5 MP/4 MP HDTVI video input and live view Independent configuration for each channel, including resolution, frame rate, bit rate, image ...
Page 10
DS-6700HUHI-K Series Encoder User Manual Supports pause, fast forward, slow forward, skip forward, and skip backward when playback, locating by dragging the mouse on the progress bar Alarm and Exception Configurable arming time of alarm input/output Alarm for video loss, motion detection, video tampering, abnormal signal, video ...
DS-6700HUHI-K Series Encoder User Manual Chapter 1 Introduction Front Panel Figure 1. 1 DS-6704HUHI-K Front Panel Figure 1. 2 DS-6708/6716HUHI-K Front Panel Table 1. 1 Indicator Description Indicator Description POWER Lights in green when the device is powered on. STATUS Lights in green when data is being read from or written to HDD.
DS-6700HUHI-K Series Encoder User Manual The rear panel of DS-6704/6716HUHI-K provides 4/16 video input interfaces. Table 1. 2 Interface Description Description VIDEO IN AUDIO IN, RCA Connector AUDIO OUT, RCA Connector RS-232 Serial Interface LAN Network Interface RS-485 Serial Interface...
DS-6700HUHI-K Series Encoder User Manual 1.3.2 Alarm Output Connections DS-6700HUHI-K supports the open/close relay input as the alarm output mode. The alarm input can be selected to NO or NC. Different alarm output connection methods are applied to the AC or DC load. Please refer to the...
DS-6700HUHI-K Series Encoder User Manual Chapter 2 Activation You are required to activate the encoder first by setting a strong password for it. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. 2.1 Activating via Web Browser Steps: Power on the encoder, and connect the encoder to the network.
DS-6700HUHI-K Series Encoder User Manual Figure 2. 2 Security Question Configuration and Export GUID File (Optional) Configure the security questions or export the GUID file. Refer to Chapter 11.1.4 Configuring Security Questions and Chapter 11.1.5 Exporting GUID File. Or click Cancel to skip the configuration.
Page 16
DS-6700HUHI-K Series Encoder User Manual Click the Device Management icon to enter the Device Management interface, as shown in the figure below. Figure 2. 4 Control Panel Check the device status from the device list, and select an inactive device.
Page 17
DS-6700HUHI-K Series Encoder User Manual Figure 2. 6 Modifying the Network Parameters Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Input the password to activate your IP address modification.
DS-6700HUHI-K Series Encoder User Manual Chapter 3 Getting Started via WEB Browser The device can also be accessed by WEB Browser for configuration and operation. The supported WEB browsers include: Internet Explorer 6/7/8/9, Firefox 3.5 and above, Chrome 8 and above, Safari 5.0.2 and above, Windows XP SP1 and above (32-bit).
Page 19
DS-6700HUHI-K Series Encoder User Manual Figure 3. 2 Download and Install Plug-in (2) Click Run or Save on the pop-up warning message box. Figure 3. 3 Run Web Components (3) Click Next on the pop-up Setup dialog box. Figure 3. 4 Click Next...
DS-6700HUHI-K Series Encoder User Manual Figure 3. 5 Install the Web Components 3.2 Resetting Password Purpose If you forget the password of the device, you can set a new password by answering security questions or importing GUID file. Before you start Set the security questions and answers, or export the GUID file first in user management.
DS-6700HUHI-K Series Encoder User Manual Figure 3. 7 GUID File Verification Click Next to set new password. Figure 3. 8 Set New Password Click Next and the password is modified. It will jump to the login interface. Figure 3. 9 Password Modified 3.3 Main Page Introduction...
Page 22
DS-6700HUHI-K Series Encoder User Manual Menu Bar PTZ Control Device List Preset and Patrol Settings Live View Window Toolbar Figure 3. 10 Main Page Description of the live view page: Menu Bar: Enter the Live View, Playback, and Configuration page respectively.
DS-6700HUHI-K Series Encoder User Manual Chapter 4 Live View Live view shows you the video image getting from the connected camera in real time. After successful login, the system will enter the live view page automatically. 4.1 Starting Live View Steps: In the live view window, select a playing window by clicking the mouse.
DS-6700HUHI-K Series Encoder User Manual Enable e-PTZ Previous/Next page Audio on/off Switch to full-screen live view mode. Before using two-way audio function or recording with audio, please select the Video Type to Video & Audio on Chapter 6.2 Configuring Video/Audio Settings.
DS-6700HUHI-K Series Encoder User Manual The saving path for the captured pictures can be set at the Configuration > Local page. The image is saved as a JPEG file on your computer. 4.3 Operating PTZ Control Before you start: Make sure the encoder is connected with the camera/dome which supports PTZ function.
DS-6700HUHI-K Series Encoder User Manual Figure 4. 4 PTZ Control Panel Click the zoom/iris/focus buttons to realize lens control. Refer to the following table for description of PTZ control buttons: Table 4. 2 Description of PTZ Control Buttons Button Description...
Page 27
DS-6700HUHI-K Series Encoder User Manual Figure 4. 5 Set a Preset Use the PTZ control buttons to move the lens in the desired position. You can use any of the following commands: • Pan the camera to the right or left.
DS-6700HUHI-K Series Encoder User Manual 4.3.3 Setting/Calling a Patrol Setting a Patrol: In live view mode, click the from the PTZ control area to enter the patrol settings interface. Select a patrol number from the patrol list for settings. Figure 4. 7 Patrol Settings Click to edit the patrol.
DS-6700HUHI-K Series Encoder User Manual Calling a Patrol: The PTZ camera will move according to the predefined patrol path when you call a patrol. In live view mode, select a predefined patrol from the list and click to start calling a patrol, and click stop the calling.
DS-6700HUHI-K Series Encoder User Manual Chapter 5 Device Configuration 5.1 Local Configuration Go to Configuration > Local to enter the Local Configuration interface. Figure 5. 1 Local Configuration Configure the following settings: Protocol Type: Set the protocol type of stream transmission to TCP, UDP, or MULTICAST.
DS-6700HUHI-K Series Encoder User Manual 7.1.1 Configuring Motion Detection. Image Size: Select the split screen view mode to 4:3, 16:9 or Auto-fill. Auto Start Live View: Enable or disable the auto-start of live view once you open the Web browser.
DS-6700HUHI-K Series Encoder User Manual 5.2.2 Configuring Time Settings Steps: Click Configuration > System > System Settings > Time Settings to enter the Time Settings interface: Figure 5. 3 Time Settings Select the Time Zone that is closest to the device’s location from the drop-down menu.
DS-6700HUHI-K Series Encoder User Manual If the device is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the device is set up in a more customized network, NTP software can be used to establish a NTP server used for time synchronization.
DS-6700HUHI-K Series Encoder User Manual Go to Configuration> System > System Settings > RS-232. Configure the Baud Rate, Data Bit, Stop Bit, Parity, Flow Control, and Usage. Figure 5. 7 RS-232 Settings If you want to connect the camera by the RS-232 port, the parameters of the RS-232 should be exactly the same with the parameters you configured here.
DS-6700HUHI-K Series Encoder User Manual Figure 5. 8 RS-485 Settings 2. Set the RS-485 parameters. By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop bit is 1 and the Parity and Flow Control is None.
DS-6700HUHI-K Series Encoder User Manual Default Gateway, MAC Address, and MTU settings The valid value range of MTU is 500 to 1500. If the DHCP server is available, you can check DHCP to automatically obtain an IP address and other network settings from that server.
DS-6700HUHI-K Series Encoder User Manual 5.3.3 Configuring DDNS Settings If your device is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used for network access. Prior registration with your DDNS Provider is required before configuring the system to use DDNS.
DS-6700HUHI-K Series Encoder User Manual • NO-IP: Enter the Server Address as www.noip.com. Enter the Domain you registered. Enter the User Name and Password. Confirm the password. Click Save and then you can view the camera with the domain name.
DS-6700HUHI-K Series Encoder User Manual Click Save to save the settings. 5.3.5 Configuring Email Settings Purpose: The device can be configured to send an Email notification to all designated receivers if an alarm event is detected, e.g., motion detection event, video loss, tamper-proof, etc.
DS-6700HUHI-K Series Encoder User Manual Attached Image: Check the checkbox of Attached Image if you want to send email with attached alarm images. Interval: The interval refers to the time between two actions of sending attached pictures. Authentication (optional): If your mail server requires authentication, check this checkbox to use authentication to log in to this server and enter the login User Name and Password.
DS-6700HUHI-K Series Encoder User Manual Figure 5. 17 UPnPTM Settings-Auto Click Save to save the settings. 5.3.7 Configuring HTTPS Settings Purpose: HTTPS (Hyper Text Transfer Protocol Secure) ensures the data transferred is encrypted using Secure Socket Layer (SSL) or Transport Layer Security (TLS). HTTPS provides authentication of the web site and associated web server that one is communicating with and create a secure channel over an insecure network.
DS-6700HUHI-K Series Encoder User Manual Figure 5. 18 Create Self-signed Certificate Enter the country, host name/IP, validity and other information. Click OK to save the settings. If you already had a certificate installed, the Create Self-signed Certificate is grayed out.
DS-6700HUHI-K Series Encoder User Manual Figure 5. 21 Service Terms Create the verification code in the Verification Code text field. Confirm the verification code. Read Terms of Service and Privacy Policy before enabling the service. Click OK to save the settings and return to the Hik-Connect page.
DS-6700HUHI-K Series Encoder User Manual The multicast address can be configured to realize live view for more than the maximum number of cameras through network. A multicast address spans the Class-D IP range of 224.0.0.0 to 239.255.255.255. It is recommended to use the IP address ranging from 239.252.0.0 to 239.255.255.255.
DS-6700HUHI-K Series Encoder User Manual Chapter 6 Camera Settings 6.1 Configuring Image 6.1.1 Configuring Display Settings Purpose: You can configure the scene, brightness, contrast, saturation, etc. in the display settings. Steps: Go to Configuration > Image > Display Settings to enter the Display Settings page.
DS-6700HUHI-K Series Encoder User Manual 6.1.2 Configuring OSD Settings Purpose: You can customize the camera name, time/date format, display mode, and OSD size displayed on the live view. Steps: Go to Configuration > Image > OSD Settings. Figure 6. 2 OSD Settings Check the corresponding checkbox to select the display of camera name, date or week if required.
Page 47
DS-6700HUHI-K Series Encoder User Manual 2. Select the camera to configure privacy mask. 3. Check the checkbox of Enable Privacy Mask to enable this function. Figure 6. 3 Privacy Mask Settings Click Draw Area. Draw the mask area by clicking and dragging the mouse in the live video image.
DS-6700HUHI-K Series Encoder User Manual 6.2 Configuring Video/Audio Settings Steps: Go to Configuration > Video/Audio > Video to enter the Video Settings page. Figure 6. 4 Video Settings Select the camera from the drop-down list to configure. View the Front-end Resolution.
Page 49
DS-6700HUHI-K Series Encoder User Manual video quality with a lowered bitrate. The cameras support enabling H.264+/H.265+ if the video encoding is H.264/H.265 for the main stream. For the connnected camera, the H.264+ or H.265+ should be supported by the camera.
DS-6700HUHI-K Series Encoder User Manual Chapter 7 Event Settings 7.1 Configuring Basic Events Purpose: You can configure the basic events by following the instructions in this section, including motion detection, video tampering, alarm input, alarm output, and exception, etc. These events can trigger the linkage methods, such as Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
Page 51
DS-6700HUHI-K Series Encoder User Manual Figure 7. 1 Motion Detection-Area Settings (2) Click Draw Area. Draw motion detection area by dragging the mouse in the live video image. By default, the full screen motion detection is configured. (3) Click Stop Drawing to finish drawing.
Page 52
DS-6700HUHI-K Series Encoder User Manual Figure 7. 2 Motion Detection-Arming Schedule Settings (2) Click on the time bar and drag the mouse to select the time period. Figure 7. 3 Motion Detection-Edit Arming Schedule Click on the selected time period, you can adjust the time period to the desired time by either moving the time bar or input the exact time period.
Page 53
DS-6700HUHI-K Series Encoder User Manual Figure 7. 4 Motion Detection-Linking Method Select the alarming linkage method(s) including Audible Warning, Notify Surveillance Center, Send Email and Upload Pictures to Cloud. Audible Warning Trigger an audible beep when an alarm is detected.
DS-6700HUHI-K Series Encoder User Manual To trigger an external alarm output when an event occurs, you need to go to the Alarm Output Settings to set the related parameters. Refer to Chapter 7.1.3 Configuring Alarm Output for reference. Select the channel you want to trigger recording when a motion detection event occurs.
Page 55
DS-6700HUHI-K Series Encoder User Manual Figure 7. 7 Alarm Input Settings-Arming Schedule Click the Linkage Method tab to set the actions taken for the alarm input. Please refer to Step 7 in Chapter 7.1.1 Configuring Motion Detection. Figure 7. 8 Alarm Input Settings-Linkage Method You can also select the PTZ linking for the alarm input if your camera is installed with a pan/tilt unit.
DS-6700HUHI-K Series Encoder User Manual 7.1.3 Configuring Alarm Output Steps: Go to Configuration> Event > Basic Event > Alarm Output to enter the Alarm Output Settings page. Figure 7. 9 Motion Detection-Alarm Output Settings Select the Alarm Output No. Set the Delay time to 5sec, 10sec, 30sec, 1min, 2min, 5min, 10min or Manual. The Delay refers to the time duration that the alarm output remains in effect after alarm occurs.
DS-6700HUHI-K Series Encoder User Manual Figure 7. 10 Video Loss Alarm Settings Select the camera to configure the video loss alarm. Check Enable Video Loss Detection. Set the arming schedule for video loss detection. Please refer to Step 6 in Chapter 7.1.1 Configuring Motion Detection.
DS-6700HUHI-K Series Encoder User Manual Figure 7. 11 Video Tempering Alarm Settings Check Enable Video Tempering. Set the tamper-proof area. Please refer to Step 5 in Chapter 7.1.1 Configuring Motion Detection. Set the arming schedule for tamper-proof. Please refer to Step 6 in Chapter 7.1.1 Configuring Motion Detection.
DS-6700HUHI-K Series Encoder User Manual Figure 7. 12 Handling Exceptions Click Save to save the settings. 7.2 Configuring Smart Event You can configure the smart events by following the instructions in this section, including audio exception detection, scene change detection, intrusion detection, and line crossing detection. These events can trigger the linkage methods, such as Notify Surveillance Center, Send Email, Trigger Alarm Output, etc.
DS-6700HUHI-K Series Encoder User Manual Figure 7. 13 Audio Exception Detection Select the Camera. Check the checkbox of Audio Loss Detection to enable the audio loss detection function. Check the checkbox of Sudden Increase of Sound Intensity Detection to detect the sound steep rise in the surveillance scene.
Page 61
DS-6700HUHI-K Series Encoder User Manual Figure 7. 14 Intrusion Detection Select the Camera. Check the checkbox of Enable Intrusion Detection to enable the function. Select a region number from the drop-down list of Region. Region: A pre-defined vertexes area on the live view image. Targets, such as, people, vehicle or other objects, who enter and loiter in the region will be detected and trigger the set alarm.
DS-6700HUHI-K Series Encoder User Manual The Sensitivity of the detection is supported by certain camera models. Refer to actual display for details. Drag the slider to set the percentage. Percentage: Range [1-100]. Percentage defines the ratio of the in-region part of the object which can trigger the alarm.
DS-6700HUHI-K Series Encoder User Manual Figure 7. 15 Line Crossing Detection Select the Camera. Check the checkbox of Enable Line Crossing Detection to enable the function. Click Area Settings tab and select the line from the drop-down list. Click Draw Area, and a virtual line is displayed on the live video.
Page 64
DS-6700HUHI-K Series Encoder User Manual Figure 7. 16 Scene Change Detection Select the Camera. Check Enable to enable scene change detection. For the analog cameras, the line crossing detection and intrusion detection conflict with sudden scene change detection. You can only enable one function. If you have enabled line crossing detection or intrusion detection, when you enable sudden scene change detection and save the settings, the following attention box pops up as below.
Page 65
DS-6700HUHI-K Series Encoder User Manual Motion Detection. Click Save to save the settings.
DS-6700HUHI-K Series Encoder User Manual Chapter 8 Record Settings Before you start Make sure the encoder is connected with HDD or network disk, and the HDD or network disk has been initialized for the first time to use. 8.1 Configuring Record Schedule...
Page 67
DS-6700HUHI-K Series Encoder User Manual checkbox of Trigger Channel on the Linkage Method of Motion Detection settings interface. Refer to Chapter 7.1.1 Configuring Motion Detection. Record Triggered by Alarm If you select Alarm, the video will be recorded when the alarm is triggered.
DS-6700HUHI-K Series Encoder User Manual the settings. Click Save to save the settings. 8.2 Configuring Holiday Settings Purpose: You may want to have different plan for recording on holiday. Follow the steps to configure the record schedule on holiday. Steps: Go to Configuration>...
Page 69
DS-6700HUHI-K Series Encoder User Manual The Holiday option is available in the Schedule drop-down list when you have enabled holiday schedule in holiday settings.
DS-6700HUHI-K Series Encoder User Manual Chapter 9 HDD Management 9.1 Initializing HDD Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your encoder. Steps: Go to Configuration > Storage > Storage Management > HDD Management.
DS-6700HUHI-K Series Encoder User Manual 9.2 Configuring Net HDD For the models with SATA disks connected, the configuration of network disk is selectable. Before you start: The network storage device is available within the network and is properly connected. The network storage device is configured with NAS or IP SAN mode (please refer to the User Manual of IP SAN/NAS).
Page 72
DS-6700HUHI-K Series Encoder User Manual You can also manually add the NAS or IP SAN by entering the IP address of the server and file path in the text filed. NAS: Enter the IP address of the storage device, and the default file path is /dvr/share, in which the share name is user-defined during creating the DVR of the network storage.
DS-6700HUHI-K Series Encoder User Manual Up to 8 NAS disks and 1 IP SAN disk can be connected. 9.3 Checking S.M.A.R.T. Information Purpose: The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures.
DS-6700HUHI-K Series Encoder User Manual 9.4 Detecting Bad Sector Purpose You can detect the bad sector of the HDD to check the status of the HDD. Go to Configuration > Storage > Storage Management > HDD Detection. Click the Bad Sector Detection tab to enter the page.
DS-6700HUHI-K Series Encoder User Manual Figure 9. 10 Cloud Storage Click Get to get the authentication code. And then copy the authentication code to the Authentication Code text filed. Click Save to save the settings. Enter the cloud storage page again about 20s later. When the Status shows online, it indicates the successful registration.
Page 76
DS-6700HUHI-K Series Encoder User Manual Figure 9. 11 Other Settings Check Enable HDD Sleeping, thus to decrease the power consumption of the device and extend the life of the HDDs if the HDDs are free of working for a long time.
DS-6700HUHI-K Series Encoder User Manual Chapter 10 Playback Purpose: The recorded video files can be remotely played back through the WEB browser. Steps: Click Playback on the menu bar to enter playback page. Figure 10. 1 Playback Page Click the camera from the device list for playback.
Page 78
DS-6700HUHI-K Series Encoder User Manual Figure 10. 3 Playback Toolbar Table 10. 1 Description of Toolbar Icons Icon Operation Icon Operation Select window-division mode Reverse playback Play/Pause Stop playing Slow forward Fast forward Play by single frame Stop all channels from playing...
DS-6700HUHI-K Series Encoder User Manual Chapter 11 User Management 11.1 User Management Go to Configuration > System > User Management > User Management to enter the User Management page. Figure 11. 1 User Management The admin user is allowed to create normal users. And up to 31 users can be created.
DS-6700HUHI-K Series Encoder User Manual monthly or weekly can better protect your product. Figure 11. 2 Add a User Different user level is given different permissions: • Operator: The Operator user level has permission of Local Log Search in Local Configuration, Remote Log Search and Two-way Audio in Remote Configuration and all operating permission in Camera Configuration.
Page 81
DS-6700HUHI-K Series Encoder User Manual Click Modify to enter the modification interface. Figure 11. 4 Modify the Admin...
DS-6700HUHI-K Series Encoder User Manual Figure 11. 5 Modify the Operator Modify the editable parameters. You are highly recommended to use the strong password. Configure the user permission for the user. Click OK to save the settings. You need the admin password to modify the admin user or operator.
DS-6700HUHI-K Series Encoder User Manual Click OK to delete the selected user account. 11.1.4 Configuring Security Questions Purpose: You can set the security question for the admin and other users. In case of forgetting the password, you can retrieve the password by answering the security questions.
DS-6700HUHI-K Series Encoder User Manual Go to Configuration > System > User Management > User Management. Click Export GUID File and the window pops up as below. Figure 11. 9 Confirm the Admin Password Enter the Admin Password and click OK.
DS-6700HUHI-K Series Encoder User Manual Chapter 12 Log Search, Maintenance and Security Settings 12.1 Searching Log Purpose The operation, alarm, exception and information of the device can be stored in log files, which can be viewed and exported at any time.
DS-6700HUHI-K Series Encoder User Manual You can click Export to save the searched log files to local directory. 12.2 Maintenance Go to Configuration > System > Maintenance > Upgrade & Maintenance to enter the Maintenance page of the encoder. Figure 12. 2 Maintenance 12.2.1 Rebooting the Device...
DS-6700HUHI-K Series Encoder User Manual 12.2.2 Restoring Default Settings Steps: Go to Configuration > System > Maintenance > Upgrade & Maintenance > Default. Figure 12. 5 Restore Default Settings Click Restore or Default to restore device parameters. Restore: Restore the device to the default settings for the parameters except the IP address, subnet mask, gateway and port.
DS-6700HUHI-K Series Encoder User Manual 12.2.4 Upgrading the System On the Configuration > System > Maintenance > Upgrade & Maintenance > Upgrade page, click Browse to select the local update file and then click Upgrade to start remote upgrade. Figure 12. 8 Remote Upgrade 12.3 Configuring Security Settings...
DS-6700HUHI-K Series Encoder User Manual Chapter 14 FAQ Why cannot ping the Encoder? Please refer to Chapter 3 to configure the device’s IP being in the same segment as your PC, and check the cable and switch. Why the transparent channel has been set, but the encoder still cannot receive data? 1.
Page 91
DS-6700HUHI-K Series Encoder User Manual...
Need help?
Do you have a question about the DS-6700HUHI-K Series and is the answer not in the manual?
Questions and answers