Summary of Contents for HIKVISION DS-630XDI Series
Page 1
DS-630XDI Series Decoder Server USER’S MANUAL Version 2.0.0...
Page 2
The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book.
Page 3
Preventive and Cautionary Tips Before connecting and operating your DVR, please be advised of the following tips: • Ensure unit is installed in a well-ventilated, dust-free environment. • Keep all liquids away from the DVR. • Please check the power supply to avoid the damage caused by voltage mismatch. •...
TABLE OF CONTENTS C H A P T E R 1 ........................6 Introduction ..........................6 1.1 Description ........................7 1.2 Features ........................... 7 C H A P T E R 2 ........................10 Structure ..........................10 2.1 Front Panel ........................11 2.2 Rear Panel ........................
Page 5
Appendix A Specifications ....................33 Appendix B FAQ ......................35 Appendix C Glossary ....................... 36...
1.1 Description Developed by Hikvision based on TI DM648 platform, DS-630XD is a kind of multi-purpose video/audio decoder which is capable of allowing the coded images from HIK DVR/DVS or other encoding devices to be decoded and displayed on the TV wall after transmission via IP network. Specially designed for the allocation and management of the video surveillance system, DS-630XD supports multiple network transmission protocols, and it applies the code downloaded in FLASH, ensuring high stability and reliability of system performance.
Page 8
the HIK customized protocols are adopted; and support RTP over TCP and RTP over UDP when standard H.264 and MPEG4 are adopted. Dynamic decoding: dynamically input encoder’s IP address and switch decoding channels; maintain rapid decoding and switch. Cycle decoding: set multiple remote monitoring channels on a decoding channel, and the decoder is capable of performing cycle decoding according to the configured sequence and time.
Page 9
A maximum of 32 users can be created by the system, including 1 administrator and 31 users. The user name of the administrator is admin, which cannot be modified, and the password is allowable to be modified by the administrator only; no deletion of the administrator is allowed, and the administrator is authorized to set the operation permissions for normal users.
2.1 Front Panel 2.2 Rear Panel DS-6308D Rear Panel Interface Connections VIDEO/AUDIO OUT BNC connectors for video/audio output LINE IN 1 BNC connector for voice talk audio in, connects to active audio input device. LINE OUT 1 BNC connector for voice talk audio out, connects to audio output device, e.g. sound box.
2.3 Alarm Connections 2.3.1 Alarm Input Connections DS-630XD supports the relay input as the alarm input mode. For the alarm input signal not in open/close open/close relay signal mode, please follow the connections shown as below: Alarm input connections for Emerson Alarm: Alarm input connections for Normal Alarm: 2.3.2 Alarm Output Connections DS-630XD supports the...
Please note the different connections of JJ1 shown above. For DC load, JJ1ca be safely used both in NC and NO methods, and it is recommended to use within the limit of 12V/1A. For external AC input, JJ1 must be open. The motherboard provides two jumpers, each corresponding to one alarm output.
Description: This chapter is about the network parameters configuration of Hikvision DS-630XDI Decoder. The DS-630XDI factory default user name is admin, password is 12345. The DS-630XDI factory default IP address is 192.0.0.64. The network parameters need to be setup before the decoding channel configuration. The network parameters are used to connect with the software which is applied to set the decoding channels.
Page 16
Figure 3.1.2 Step4: Serial port setup. Set port parameters in “COM1 Properties” dialogue box as follow: (Fig 3.1.3) Figure 3.1.3 The parameters should be: Bits per second: 115200 Data bits: 8 Parity: None Stop bits: 1...
Flow control: None Press “Apply” and “OK” after the setup. Press “Enter” under Hyper Terminal interface. When “[root@dvrdvs/]#” appears, the connection is established. Figure 3.1.4 Step5: Disconnect and save connection According to the tips, disconnect and save “HK” for the next time. After saving, there will be a new “Hyper Terminal”...
Page 18
Figure 3.2 Commands Description: Commands Utilities helpm Console help command is used to print common commands, show as Figure 3.2. Show the current IP address of decoder. Command format: getIp “Enter”. getIp setIp Setup decoder IP address. Command format: setIp IP: mask, e.g. setIp 192..168.1.11:255.255.255.0 Show current decoder gateway address.
4.1 Decoder Configure Software Please open the accessory to get the disk, there is the iVMS4000 V2.0 software in it supplied by HIKVISION, please double click the icon to set up it. The following section has described the configuration of decoder through the software.
4.2 Add Decoder Click “ ”, then click “ ” to enter the decoder setting interface. Right click the “Decoder list”, and select “Add decoder”, or click “ ”to add decoder. Input decoder name, IP, Port, Username, Password, and click ”OK” to finish adding decoder.
supports 4-channel decoding. After added successfully, the decoder channels will be displayed in the decoder list. 6300DI Series decoder supports VGA, so it displays the BNC and VGA outputs differently Right click a decoder and select “Modify decoder” or click “ ”, user can modify the decoder;...
Page 23
Export/import config file Right click a decoder, user can select “Export device config file” and save the device configuration file in “C:\SaveRemoteCfgFile” folder by default. If user has saved the config file before, select “Import config file to device” to import the existed configuration to the decoder. Decoder Status Select “Decoder work status”, the status of decode will be displayed in the following list.
4.4 TV Wall Settings Enable/Disable decode output After adding decoder, the decode channel is not in use by default. Drag the channel to the blank interface on the right, it will enable this channel. When a channel is enabled, clicking “...
Page 25
By right clicking the decoder channel, user can change the division mode. The section will be different depend on the device type. Shown as below: Decode channel Output division No. 630xDI: BNC output 1, 4 6301DI: VGA output 1, 4 6304DI VGA1 output 1,4,9...
Decode channel position management After having enabled decode output and configured the division, user can change the size and position of the display window. Click the mouse and hold on the title below the window to change its position. By dragging a border of the decoder, user can change the size of the window.
Page 27
Area Description Area Description Device list Preset list Decode channel display Decode channel video Decode channel state display display Enter TV Wall control interface, the decode channel area will display as user-defined. Click to hide the decode video and states, or click to resume.
4.5.1 Video decode control Select the decode window, drag one channel into it and the decoder will start decoding this channel. The decoder video display area will display the real-time video, and the state area will display the states of current decoding. Stop decoding Right click the decode channel, select “Stop decoding”...
Voice control Right click the decoding window, choose ”Open voice” to open voice; When the voice is on, right click the decoding window, choose “Close voice” to close voice. Attention : Only the stream type “Audio & Video” can support the function “Open voice”. Decoding image control Choose the decoding window, and the image display area will show the current decoding image.
Page 30
display the states of current decoding. Pause cycle decoding Right click the cycle decoding window, select “Pause cycle decoding” or click “ ” to pause the cycle decoding. Resume cycle decoding When the cycle decoding is off and right click on the decoding window, select “Resume cycle decoding” or click “...
Configure the cycle decoding time Click the icon ”Setup”—“Software configuration” to configure the cycle decoding time. The default cycle time is 20s. After configuring the time , click the icon ”save” to save the configuration. 4.5.3 PTZ control If the decoder connected PTZ, user can operate the PTZ through this software.
Appendix B FAQ Why cannot ping the decoder? Please refer to Chapter 3 to configure the decoder IP being in the same segment as your PC, and check the cable and switch. Why the transparent channel has been set, but the encoder still cannot receive data? Please 1.
Appendix C Glossary Dual Stream Dual stream refers to that one channel of video stream can be divided into double independent output streams through the video encoder. Shown as below: Main Stream Video Stream Video Encoder Sub Stream The resolution, frame rate, bitrate and other parameters of the output stream are independently programmable. The two streams generated may meet different application demands, e.g., one stream is used for HDD storage, and the other for transmission via Internet.