Hyundai N300-P Instruction Manual page 129

Economical inverter

page of 133

/ 133
Contents
Table of Contents
Bookmarks

Table of Contents

N300-P INSTRUCTION MANUAL

(3) Common specification for 200V/400V class

N300-

Inverter Model

055LFP/HFP

Enclosures

IP20(NEMA1)

Control system

Sine-wave modulation PWM system

Output frequency range

0.1 400Hz

Frequency accuracy

Digital command 0.01% for Max. frequency, analog frequency 0.2% (25 10 )

Frequency resolving power

Digital setting : 0.01Hz, Analog setting : Max. frequency/4000

Voltage/frequency characteristic

V/f option variable, V/f control, (constant torqu e, reduced torque)

Speed fluctuation

0.5%

Overload current rate

120% for 60s,150% for 0.5 second

Stating torque

200% / 0.5Hz

DC Braking

on starting and decelerating by stop command, inverter operates under operation setting

frequency.Or inverter operates with external input (Breaking power, time, frequency can be set.)

Setting by

Operator

DC0 10V, -10 +10V (input impedance 10Kohn), 4 20mA (input impedance 100ohm)

Volume

Extend signal

Setting with RS485 communication

Run/Stop

Operator

Run/

Forward Run/Stop(1a connect),reverse command is impossible on assigning of terminal(selection of 1a, 1b is possible),input of 3 wires is possible.

Volume

Stop

Extend signal

Setting with RS485 communication

Use by selecting terminals from

Intelligent input terminal

Reverse command(RV), multi-speed 1-4(CF1-CF4), jogging(JG), extemal dc braking(DB), 2nd control(SET), 2nd acceleration(2CH), free-run stop(FRS), extemal trip(EXT),

USP function(USP), commercial change(CS), software lock(SFT), analog input voltage/current/select(AT), 3rd control(SET3), reset inverter(RS), 3 wire run(STA), 3wire keep

(STP), 3wire direction selection(F/R), PID selection valid/invalid(PID), PID integrating reset(PIDC), control gain change(CAS), remote control, up function(UP), remote control

down function(DWN), remote control data clear(UDC), compulsion operation(OPE),multi-speed bit 1-7(SF1-SF7), overload ristriction change(OLR), torque limit exist or no(TL),

torque limit change1(TRQ1), torque limit change12(TRQ2), P/PI change(P/PI), brake confirmation (BOK), orientration(ORT),LAD cancel(LAC), position deviation dear(PCLR),

90 degrees the phase difference permission(STAT), permissive input signal for FW/RV(ROK), no assign (NO)

Thermistor input terminal

1 terminal

Signal during rus(RUN), Frequency arrival type 1 signal(FA1), Frequency arrival type 2 signal(FA2), Overload advance notice signal(OL), Output deviation for PID

control(OD), Alarm signal(AL), Arrival signal for only setting frequency(FA3), Over torque(OTQ), Instantaneous stop signal(IP), Under voltage signal(UV), Torque limit

Intelligent output terminal

(TRQ), RUN time over(RNT), ON time over(ONT), Thermal caution(THM), Brake opning(BRK), Brake error(BER), Zero speed detect signal(ZS), Speed deviation

excessive(DSE), Positioning completion(POK), Arrival signal for over setting frequency2(FA4), Arrival signal for only setting frequency2(FA5),

Overload advance notice signal2(OL2), Alarm cord 0-3(AC0-AC3)

Intelligent monitor output terminal

Analog voltage output, analog current output, pulse line output

Output frequency, output current, frequency conversion value, trip history, input output terminal state, input electric power, output voltage, motor torque

Display monitor

V/F free setting(7points), Upper/lower frequency limitter, Frequency jump, curve adjustable speed, manual torque boost level/Braking

point, Analog meter adjustment, Starting frequency, Carrier frequency adjustment, Electronic thermal free setting, External start/end

Other function

(frequency/tate), Analog input selection, Trip retry, Reduced voltage start, Overload restriction, energy-saving operation, Restarting

after an instantaneous power failure, Various kinds signal output, Initialization value setting, Automatic deceleration at the time of

the power supply block, AVR function, Fuzzy, Autotuning(Online/Offline), High torque multi running(Sensor-less vector control with 1

inverters of 2 motors)

0.5 12kHz

Carrier frequency range

Over-current, over-voltage, under-voltage, electronic thermal lecvel, abnormal trouble, ground fault current on starting, instantaneous stop, USP error, open-phase

Protection function

error, control resistoroverload, CT error, external trip, communication error.

Frequency temperature/Preservation

-10

temperature/humidty

5.9m/s (0.6G), 10 55Hz

Vibration

Under 1000m above sea level, indoors (Installed away from corrosive gasses dust)

Using place

Paint color

Grey(Munsell 8.5 YR 6.2 / 0.2 )

Option