HP StorageWorks User Manual page 72

3. In the Device tree, select the port (WWN) you want to connect from the WWNs displayed. External LUs
that can be connected from the port (WWN) selected in the tree appear in the Device list.
4. In the Device list, select the external LUs you want to map as internal XP LDEVs, right-click, and select
Add LU (Auto). The Auto Map Setting window
5. Set the attributes for the external LUs you selected on the Device list.
NOTE:
• To select the first CU:LDEV number of the mapped destination internal XP LDEVs and the mapping
interval, go to
• To let External Storage XP select the first CU:LDEV number, go to
6. Click Select LDEV. The Select LDEV window appears.
7. Select the first CU:LDEV number of the mapped destination internal XP LDEVs and the mapping
interval.
8. Click OK. The Auto Map Setting window appears.
9. If you do not want to automatically set the primary and alternate paths, but you want to specify the
paths to be set as candidates for the primary and alternate paths, click Select Paths. The Select Paths
window appears.
To automatically set alternate paths, go to
10.Select the path and exclude it from the list of the candidates for the primary and alternate paths. For
instructions, see
11.Click OK. The Auto Map Setting window appears.
12.Click OK. The Auto Map Setting window closes, and mapping the internal CU:LDEV numbers to the
external Lus starts.
NOTE:
selected on the Device list, all processing is canceled and the message pane appears.
• After the CU:LDEV number mapping is complete, if the SSID setting is required, the SSID window
(Figure
• If the SSID setting is not necessary, the LU Operation pane appears. Settings appear in blue italics
in the Device tree and Device list. The contents specified in the Auto Map Setting window appear in
the Preset list. To check setting details, right-click the setting in the Preset list, and select Detail. To
cancel settings, right-click the setting in the Preset list, and select Delete. Go to
13.If you need to set an SSID to the mapped internal XP LDEV, the SSID window appears. When storage is
partitioned using XP Disk/Cache Partition, select the SLPR number in the SLPR list. If you select the
Limited check box and select the SLPR number, only SSIDs that can be used for the selected SLPR can
be set. If you do not select the Limited check box, you can set the SSID from all of the unused SSIDs
regardless of the selected SLPR number. Right-click the CU:LDEV number on the SSID window, and
select Set SSID. The Set SSID window
14.Enter the SSID on the Set SSID window. If you selected the Limited check box on the SSID window, only
SSIDs that can be used in SLPR selected on the SSID window appear in the list. If you do not select the
Limited check box on the SSID window, all of the unused SSIDs appear in the list, regardless of the
selected SLPR. You can enter 0x0004 to 0xFFFE as an SSID.
15.Click OK. The Set SSID window closes, and the LU Operation pane appears.
Settings appear in blue italics in the Device tree and Device list. Settings appear in the Preset list. To
check setting details, right-click the setting in the Preset list, and select Detail. To cancel settings,
right-click the setting in the Preset list, and select Delete.
16.Click Apply. A confirmation message appears.
If you already stopped the application, go to
Cancel to close the message panel, stop the application, and retry the operation.
17. If you already stopped the application, click OK. A confirmation message appears.
72 External Storage XP for the XP12000/XP10000
Attributes for all LUs mapped at one time are identical.
step 6.
"Mapping external LUs individually (Add
If the CU:LDEV numbers cannot be mapped properly because too many external LUs are
35) appears. Go to step
(Figure 37) appears.
step 12.
LU)" on page 60.
13.
(Figure 36) appears.
step 17. If you have not stopped the application, click
step 9.
step 16.