Download Print this page

HP StorageWorks 2/16 - SAN Switch Installation Manual

Universal rack mount kit installation
Hide thumbs Also See for StorageWorks 2/16 - SAN Switch:

Advertisement

SAN switch universal rack mount
This addendum only applies to the following documents:
© 2003 Hewlett-Packard Company
Printed in the U.S.A.
Product names mentioned herein may be trademarks of their respective companies as reflected by an associated
footnote. The information in this document is subject to change without notice.
HP StorageWorks SAN Switch 2/32 Installation Guide, Version 4.0.x
AA–RTQVB–TE (February 2003)
HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x
AA–RR84B–TE (February 2003)
HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x
AA–RSB6B–TE (February 2003)
hp StorageWorks
kit installation
Product Version: V3.0.x/V4.0.x
addendum
AV–RU6YA–TE
March 2003

Advertisement

loading

Summary of Contents for HP StorageWorks 2/16 - SAN Switch

  • Page 1 HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x AA–RR84B–TE (February 2003) HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x AA–RSB6B–TE (February 2003) © 2003 Hewlett-Packard Company AV–RU6YA–TE Printed in the U.S.A. March 2003 Product names mentioned herein may be trademarks of their respective companies as reflected by an associated...
  • Page 2 Pen-and-ink Changes This addendum consists two parts: Pen-and-ink Changes—provides instructions for locating specific text and either deleting text, replacing text with new text, or adding new text at a specific location. Page Additions—identifies where to add a page at a specific place in the document and recommends how to attach the replacement pages.
  • Page 3: Rack Mount Kit

    Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit This section provides instructions for installing the SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series or comparable EIA rack using the SAN Switch Universal Rack Mount Kit, part number 331148-B21.
  • Page 4 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit A right inner rail and a right outer rail A left inner rail and a left outer rail (14) #8-32 x 3/16-inch Phillips pan-head screw with captive star lock washer (10) #10-32 x 1/2-inch Phillips pan-head screw with captive star lock washer...
  • Page 5 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Caution: For proper airflow, the SFP media side of the SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This mounting allows air to enter from the front of the rack and to exhaust at the rear of the rack, similar to other rack-mounted equipment.
  • Page 6 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit — For an HP System/e rack, install each of the two rear mounting brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10 alignment washers as shown in Figure Figure 3: Installing the rear mounting brackets (HP System/e rack-left rear upright) HP StorageWorks SAN Switch 2/8|16|32 Installation Guide...
  • Page 7 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Right Note: This kit contains both left rails and right rails. The rails are marked with Left to distinguish the rails from each other. 4. Assemble the outer rails by completing the following steps: a.
  • Page 8 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit b. Depending on the rack you are using, complete one of the following tasks: — For an HP 9000 Series or comparable EIA rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 adapter washers in the upper and lower hole locations of the right rail.
  • Page 9 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit — For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 alignment washers in the upper and lower hole locations of the right rail. Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 alignment washers in the upper and lower hole locations of the left rail.
  • Page 10 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit 6. For the SAN Switch 2/32 and SAN Switch 2/16, perform step a. For the SAN Switch 2/8, perform step Caution: Do not use any other screws other than the fourteen that are provided.
  • Page 11 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit a. Assemble the two inner rails (one on each side) to the switch using the appropriate number (from step 5) of #8-32 x 3/16-inch Phillips pan-head screws as shown in Figure Note:...
  • Page 12 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit b. For the SAN Switch 2/8, assemble the two inner rails (one on each side) to the switch and plenum using the appropriate number (from step 5) of #8-32 x 3/16-inch Phillips pan-head screws as shown in Figure...
  • Page 13 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit 7. Insert the switch with the attached inner rails into the outer rails. Note: This step applies to both the HP System/e rack and the HP 9000 Series or comparable EIA rack.
  • Page 14 Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Figure 10: Installing the switch into a rack (HP System/e rack) 8. Tighten the nuts installed in step a of step 4 on page 5. See Figure Note: To uninstall a switch, remove the middle #10-32 x 1/2-inch Phillips pan head...

This manual is also suitable for:

Storageworks 8b - fc entry switchStorageworks san