Raymarine a Series Installation And Operation Instructions Manual page 263

System Setup Settings to optimize operation for this particular
system / installation.
About / Help Helpful information and restore to factory defaults
setting.
Exit Cancels on-screen menu.
Video setup menu
Menu item /
Description Settings / Operation
Set Thermal Color This saves the current color setting as the
Default default value.
Set Reverse Video or This toggles the infrared image between
Set Video Polarity white-hot (or red-hot if viewing a color image)
and black-hot.
Enable / Disable Color Enable or disable the thermal color palettes:
Thermal Video
• Enabled – Greyscale, Red, Sepia, Rainbow
and Fusion palettes are available.
• Disabled – Only Greyscale and Red palettes
are available.
Display Test Pattern Use the display test pattern when setting up
the color / contrast settings for your particular
display or monitor. You can switch through the 4
test patterns available.
Exit
Set symbology menu
Menu item /
Description Settings / Operation
Enable / Disable PC • Enabled – The PC icon is displayed whenever
Icon a PC is detected on the network.
• Disabled – The PC icon is not displayed.
Enable / Disable JCU • Enabled – The JCU icon is displayed
whenever a JCU is detected on the network.
Icon
• Disabled – The JCU icon is not displayed.
Display All Icons Selecting this menu item enables all available
icons.
Display Minimal Icons Selecting this menu item reduces the icon
activity:
• Position, Zoom, Rearview, Pause,
Stabilization disabled and Point Mode
enabled icons are unaffected.
• Home and Scene icons are displayed only
momentarily.
• Other icons are not shown.
Hide All Icons Selecting this option hides all icons except for:
• Position indicator
• Rearview mode enabled
• Stabilization disabled
• Point mode enabled
Exit Returns to the main menu.
Thermal camera application — Pan and tilt cameras
Surveillance mode menu
Menu item /
Description Settings / Operation
Scan Width This setting determines the distance that the
camera pans left and right when in surveillance
mode. Select from:
• Narrow — The camera will scan
approximately 20º left and right of the
center (40º total).
• Medium — The camera will scan
approximately 40º left and right of the center
(80º total). Or,
• Wide The camera will scan approximately
80º left and right of the center (160º total).
Scan Speed This option determines the speed at which the
camera pans left and right when in surveillance
mode. Select between:
• Slow
• Medium
• Fast
Exit
System Setup menu
Menu item /
Description Settings / Operation
This menu option should be enabled when
Enable / Disable
Ball-Down Installation the camera is mounted upside down in the
"ball-down" configuration.
Enable / Disable This menu option changes the JCU controls pan
Twist-to-Pan mode and zoom functions as follows:
Enabled — Pan the camera by rotating the
Puck clockwise or counterclockwise, zoom in
and out by pushing the puck in and pulling it out.
(This is default operation of the JCU).
Disabled — Pan the camera by moving the
Puck left or right, zoom in and out by rotating
the Puck clockwise and counterclockwise.
Enable / Disable High This option controls the amount of power
Power Standby used to hold the camera in position while it
is in Standby mode. The enabled setting will
consume more power, but will help ensure that
the camera is held in place in rough seas.
Note: If the camera moves when in
standby (due to shock or vibration), then the
Position indicator or Home setting may need
realigning (reset the camera to realign).
This option controls the amount of power used
Enable / Disable High
Motor Torque to hold the camera steady when in use. The
enabled setting will consume more power, but
help ensure that the camera is held in place in
rough seas.
The High Motor Torque mode may be useful for
power boats that operate at higher speeds and
experience high impact environments, and can
accept higher power consumption.
Note: If the camera moves due to shock
or vibration, then the Position indicator or
Home setting may need realigning (reset the
camera to realign).
Enable / Disable When this option is enabled the camera image
is reversed and you will see a mirror image on
Rearview Mode
the display.
Enable / Disable When this option is enabled horizontal and
Stabilization vertical stabilization is turned on. Only applies
to T470SC and T473SC.
261