Deleting Keyfob; Enrolling Proximity Tags (Optional); Deleting Proximity Tags - Visonic PowerMaxComplete User Manual

USER SETTINGS
You may now review and select any other mode on
the User menu (by clicking

Deleting Keyfob

Occupied keyfob memory locations must be cleared
(enrolled ID must be deleted) before enrolling a new
ID. To delete an existing ID, proceed as follows:
A. Select the desired memory location, as described
in the previous paragraph, steps A-C. If, for
example, you selected keyfob No. 5, the display
will read:
Keyfob No.
B. Click . The display will change to:
<OFF> to delete
C. Click . The display will change to:
Keyfob No.
Note that the dark box at the far right has
disappeared. It is now possible to enroll a new ID. It
is also possible to leave the cleared zone or memory
location free and simply exit to the main menu.

Enrolling Proximity Tags (optional)

Valid proximity tags enable you to perform variety of
functions without entering user code, for example,
arming, disarming, reading the event log, etc.
Whenever user code is required, you can simply
present a valid proximity tag instead of entering user
code.
When the system is disarmed, after presenting a
valid proximity tag to the control panel, the message
"<OK> for AWAY" is displayed. Now you can press
the button to immediately arm the
control panel, or wait for 3 second for system
automatic AWAY arming (the message "Please exit
now" will be displayed). Presenting the proximity tag
once again will DISARM the system.
Instead of pressing the
above), you can press the
/ twice (the message "<OK> for HOME" / "<OK> for
disarm" is displayed, accordingly) and then press the
press button for HOME arming /
disarming.
The control panel transmits an RF signal. A valid
proximity tag that is presented to the control panel
transmits a coded RF signal back to the control unit.
Up to 8 proximity tags can be enrolled to the PM
PRO.
26
Proximity tag enrolling involves the following steps:
A. Having
or ).
successfully (see Entering the User Settings
Menu),
(repeatedly, if necessary) until the display will
read:
B. Click
C. Click
to initiate a transmission from the chosen tag:
5
D. Present the tag to the control panel left bottom
side. In response, the "Happy Tune" (- - - –––) will
sound and the display will change to:
5
A dark box will appear at the far right, indicating that
the chosen tag has been enrolled.
E. Click
tag (2, 3,...8), as described in step D.
F. From this point on, you may continue in several
different directions:
• If you wish to enroll another tag, select the
• To return to the main menu, click
will bring back the display:
You may now review and select any other mode on
the User menu (by clicking

Deleting Proximity Tags

Proximity tag memory locations must be cleared
(enrolled ID must be deleted) before enrolling a new
button (see
ID. To delete an existing ID, proceed as follows:
button once
A. Select the desired memory location, as described
in the previous paragraph, steps A-C. If, for
example, you selected Tag No. 5, the display will
read:
B. Click
C. Click
entered your Master
Click the
E N R O L L P R O X T A G
. The display will read:
T a g N o : 1
. The display will prompt you
P R E S E N T T A G
T a g N o : 1
and enroll the next proximity
desired number by:
- Clicking to go up (6 7 8.....)
- Clicking to go down (4 3 2.....)
- Clicking <tag#>.
< O K > T O E X I T
T a g N o . 5
. The display will change to:
< O F F > T O D E L E T E
. The display will change to:
T a g N o . 5
User Code
button
. This
or ).
D-300886