Table of Contents
Advertisement
USER SETTINGS
- Clicking
•
To return to the main menu, click
This will bring back the display:
<OK> TO EXIT
You may now review and select any other mode on
the User menu (by clicking
Deleting Keyfob
Occupied keyfob memory locations must be cleared
(enrolled ID must be deleted) before enrolling a new
ID. To delete an existing ID, proceed as follows:
A. Select the desired memory location, as described
in the previous paragraph, steps A-C. If, for
example, you selected keyfob No. 5, the display
will read:
Keyfob No.
B. Click
. The display will change to:
<OFF> to delete
C. Click
. The display will change to:
Keyfob No.
Note that the dark box at the far right has
disappeared. It is now possible to enroll a new ID. It
is also possible to leave the cleared keyfob location
free and simply exit to the main menu.
Enrolling Proximity Tags (optional)
Note
for
PowerMaxComplete
feature: Each proximity tag assigned to a partition
will function as determined in "Setting the User
Codes". Therefore, each proximity tag must be
assigned a relevant user code. For example,
proximity tag 3 is assigned to user code 3.
Up to 8 proximity tags can be enrolled to the
PowerMaxComplete control panel.
Proximity tag enrolling involves the following steps:
A. Having
entered
successfully (see Entering the User Settings
Menu),
Click
(repeatedly, if necessary) until the display will
read:
E N R O L L
B. Click
. The display will read:
T a g N o :
C. Click
to initiate a transmission from the chosen tag:
P R E S E N T T A G
D. Present the tag to the control panel left bottom
side. In response, the "Happy Tune" (- - - –––) will
sound and the display will change to:
30
<keyfob #>.
or
5
5
with
partition
your
Master
User
the
P R O X T A G
1
. The display will prompt you
A dark box will appear at the far right, indicating that
.
the chosen tag has been enrolled.
E. Click
tag (2, 3,...8), as described in step D.
F. From this point on, you may continue in several
).
different directions:
• If you wish to enroll another tag, select the
desired number by:
- Clicking
- Clicking
- Clicking
• To return to the main menu, click
will bring back the display:
You may now review and select any other mode on
the User menu (by clicking
Deleting Proximity Tags
Proximity tag memory locations must be cleared
(enrolled ID must be deleted) before enrolling a new
ID. To delete an existing ID, proceed as follows:
A. Select the desired memory location, as described
in the previous paragraph, steps A-C. If, for
example, you selected Tag No. 5, the display will
read:
B. Click
< O F F > T O D E L E T E
C. Click
Note that the dark box at the far right has
disappeared. It is now possible to enroll a new ID. It
Code
is also possible to leave the cleared zone or memory
location free and simply exit to the main menu.
button
Setting the Voice Options
(Not applicable in PowerMaxComplete that does not
have VOICE option)
Remember: Voice prompts are heard over the built-
in loudspeaker subject to two conditions:
-
The voice option is enabled as shown below
-
The loudspeaker is enabled by pressing the "7"
key (see Chapter 3 - Voice ON-OFF)
Here you may select one of two options:
Enable prompts: Voice announcements
Disable prompts: No voice announcements
T a g N o :
1
and enroll the next proximity
to go up (6 7 8.....)
to go down (4 3 2.....)
<tag#>.
< O K > T O E X I T
T a g N o .
5
. The display will change to:
. The display will change to:
T a g N o .
5
. This
or
).
D-302213
Hide quick links:
Advertisement
Table of Contents
