Brocade Communications Systems NetIron CES Series Hardware Manual page 28

1
Hardware features
10-Gbps ports
The Brocade NetIron CES 2048C-4X, Brocade NetIron CES 2048F-4X, Brocade NetIron CER
2048C-4X-RT, and the Brocade NetIron CER 2048F-4X-RT come with four 10-Gigabit Ethernet ports
installed. The four 10-Gigabit Ethernet uplink ports support 10-Gigabit Small Form Factor Pluggable
(SFP+) MSA-compliant optical transceivers
The Brocade NetIron CES 2048CX, Brocade NetIron CES 2048FX, Brocade NetIron CER 2048CX,
and the Brocade NetIron CER 2048FX come with two 10-Gigabit Ethernet ports installed. A 24-port
Brocade NetIron CES,Brocade NetIron CER has a slot to accommodate a 2-port 10-Gigabit Ethernet
module. If your 24-port device does not include a 10-GbE module, you can optionally install one.
Refer to
Ethernet ports use 10-Gigabit Small Form Factor Pluggable (XFP) MSA-compliant transceivers.
Supported optics
100/1000 Ethernet Ports
The Ethernet Interface module contains 24 or 48 physical ports, through which you can connect
your device to other network devices at a speed of 100 Mbps or 1 Gbps.
Into a physical port, you must insert a fiber-optic transceiver provided by Brocade. The
SFP-compliant fiber-optic modules provide an optical transceiver or physical medium-dependent
(PMD) interface for fiber that can be used with the LAN physical layer (PHY)
The following 100 Mbps and 1 GbE optical transceivers are available from Brocade:
TABLE 5
Part number
E1MG-TX
E1MG-SX
E1MTG-SX
E1MG-SX2-1310
E1MG-LX
E1MG-LHA
E1MG-LHB
E1MG-BXD
E1MG-CWDM80-1470
E1MG-CWDM80-1490
E1MG-CWDM80-1510
E1MG-CWDM80-1530
E1MG-CWDM80-1550
E1MG-CWDM80-1570
E1MG-CWDM80-1590
E1MG-CWDM80-1610
E1MG-100FX
16
"10-Gigabit Ethernet module installation or replacement"
SFP-compliant transceivers for the 100/1000 Ethernet interface module
Description
SFP Copper, RJ-45 connector
1000Base-SX SFP optic, multi-mode fiber, LC connector
1000Base-SX SFP optic, multi-mode fiber, MTRJ connector
1310 1000Base-SX SFP optic multi-mode fiber, LC connector and support for distances
up to 2km
1000Base-LX SFP optic, single-mode fiber, LC connector
1000Base-LHA SFP optic, single-mode fiber, LC connector
1000Base-LHB SFP optic, single-mode fiber, LC connector, 150km Maximum Reach
1000Base-BXD SFP optic single-mode fiber, 1490nm, LC connector.
This optic can only be connected to an E1MG-BXU
CWDM SFP optic, 80km, 1470nm, LC connector
CWDM SFP optic, 80Km, 1490nm, LC connector
CWDM SFP optic, 80Km, 1510nm, LC connector
CWDM SFP optic, 80Km, 1530nm, LC connector
CWDM SFP optic, 80Km, 1550nm, LC connector
CWDM SFP optic, 80Km, 1570nm, LC connector
CWDM SFP optic, 80Km, 1590nm, LC connector
CWDM SFP optic, 80Km, 1610nm, LC connector
100Base-FX SFP optic multi-mode fiber, LC connector
on page 68. The two 10-Gigabit
Brocade NetIron CES and Brocade NetIron CER Hardware Guide
53-0000080-03