Zte ZXR10 8900 Series User Manual page 79

The configuration task of the three routers in
as below:
Router Loop-
back
R1 100.1.1.1
R2 100.1.1.2
R3 100.1.1.3
Configuration of R1:
R1(config)#interface vlan10
R1(config-if)#ip address 10.10.13.1 255.255.255.0
R1(config-if)#ip rsvp bandwidth 30000 10000
R1(config-if)#mpls traffic-eng tunnels
R1(config-if)#exit
R1(config)#interface vlan20
R1(config-if)#ip address 10.10.12.1 255.255.255.0
R1(config-if)#ip rsvp bandwidth 30000 10000
R1(config-if)#mpls traffic-eng tunnels
R1(config-if)#exit
R1(config)#interface loopback1
R1(config-if)#ip address 100.1.1.1 255.255.255.255
R1(config-if)#exit
R1(config)#mpls traffic-eng tunnels
R1(config)#router ospf 1
R1(config-router)#mpls traffic-eng area 0
R1(config-router)#mpls traffic-eng router-id loopback1
R1(config-router)#network 100.1.1. 0.0.0.0 area 0
R1(config-router)#network 10.10.13.0 0.0.0.255 area 0
R1(config-router)#network 10.10.12.0 0.0.0.255 area 0
R1(config-router)#exit
Configuration of R2:
R2(config)#interface vlan20
R2(config-if)#ip address 10.10.12.2 255.255.255.0
R2(config-if)#mpls traffic-eng tunnels
R2(config-if)#ip rsvp bandwidth 30000 10000
R2(config-if)#exit
R2(config)#interface vlan30
R2(config-if)#ip address 10.10.23.2 255.255.255.0
R2(config-if)#mpls traffic-eng tunnels
R2(config-if)#mpls traffic-eng backup-path tunnel22
R2(config-if)#ip rsvp bandwidth 30000 10000
R2(config-if)#exit
R2(config)#interface loopback1
R2(config-if)#ip address 100.1.1.2 255.255.255.255
R2(config-if)#exit
R2(config)#mpls traffic-eng tunnels
R2(config)#router ospf 1
R2(config-router)#mpls traffic-eng router-id loopback1
R2(config-router)#mpls traffic-eng area 0
R2(config-router)#network 10.10.12.0 0.0.0.255 area 0
R2(config-router)#network 100.1.1.2 0.0.0.0 area 0
R2(config-router)#network 10.10.23.0 0.0.0.255 area 0
R2(config-router)#exit
Configuration of R3:
R3(config)#int vlan30
R3(config-if)#ip address 10.10.23.3 255.255.255.0
R3(config-if)#mpls traffic-eng tunnels
R3(config-if)#ip rsvp bandwidth 30000 10000
R3(config-if)#mpls traffic-eng tunnels
R3(config-if)#exit
R3(config)#interface vlan10
Confidential and Proprietary Information of ZTE CORPORATION
Chapter 6 MPLS TE HOT-STANDBY Configuration
Task Tunnel
end node Tunnel1, the destination address
is 100.1.1.3
middle
node
end node
Figure 34 are shown
71