Page 1
All manuals and user guides at all-guides.com ZXR10 8900 Series 10 Gigabit Routing Switch Command Reference (IP Routing Volume I) Version 2.8.02.C ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn...
Page 2
The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.
All manuals and user guides at all-guides.com About This Manual..........i Command Introduction ........1 Manual Instruction............1 Description of Man-Machine Commands ......1 Auxiliary Function ............2 Command Modes............3 RIP Protocol ............9 address-family ipv4 vrf............ 9 auto-summary ..............10 default-metric ...............10 disable interface ............11 distance ...............11 enable interface ............12...
Page 4
All manuals and user guides at all-guides.com show ip rip networks ............26 timers basic ..............27 validate-update-source...........28 version.................28 OSPF Protocol ..........31 area authentication............32 area filter-list ..............33 area nssa ..............33 area range..............35 area sham-link ..............36 area stub ..............38 area stub-host ..............39 area virtual-link.............40 auto-cost..............42 bfd-all-interface ............42...
Page 5
All manuals and user guides at all-guides.com ip ospf fast-reroute ............57 ip ospf hello-interval ............57 ip ospf message-digest-key ..........58 ip ospf mtu-ignore ............58 ip ospf network .............59 ip ospf priority ..............60 ip ospf resync-timer............60 ip ospf retransmit-interval ..........61 ip ospf transmit-delay ............61 maximum-paths ............62 max-metric router-lsa ............62 mpls traffic-eng area............63...
Page 6
All manuals and user guides at all-guides.com default-information originate...........99 disable ............... 100 disable-snp-authentication..........101 distance ..............101 enable ............... 101 enable-snp-authentication ..........102 fast-reroute ..............102 hello padding .............. 103 hostname ..............103 ignore-lsp-errors ............104 ip router isis ............... 104 isis authentication ............
Page 7
All manuals and user guides at all-guides.com router isis..............120 router-leak ..............120 set-overload-bit ............121 show isis adjacency ............. 122 show isis circuits ............123 show isis database............124 show isis fast-reroute-topology........126 show isis hostname............127 show isis mesh-groups ..........127 show isis nsf ...............
Page 8
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com About This Manual ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command About this Manual Reference (IP Routing Volume I) ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command Reference has 16 volumes. The details are as follows: Manual Name Summary ZXR10 8900 Series (V2.8.02.C)
Page 10
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Manual Name Summary ZXR10 8900 Series (V2.8.02.C) This manual describes interface 10G Routing Switch Command configuration, DHCP and Reference (Basic Configuration VRRP-related commands in...
Reference includes 16 volumes. For details of each volume, please refer to preface of this manual. Commands in ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command Reference (Index) are listed in sequence of from letter a to letter z and in form of table. Commands of all other volumes are classified and illustrated according to different function modules.
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � Command format It describes the complete format of this command. If no for- mat is available, list it. � Parameter Description It describes parameters in this command in the form and pre- scribes the range and default value.
Use show history command in any mode, and the latest sev- eral commands in this mode will be listed. Command Modes The command modes in this manual are as follows: Confidential and Proprietary Information of ZTE CORPORATION...
Page 14
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Modes Prompt Admis- Command Function sion to Enter the Mode Mode User Enter this View simple ZXR10> Mode mode directly information after logging onto system...
Page 15
OSPF protocol parameters router isis Configure IS-IS protocol parameters router bgp Configure BGP protocol parameters router Configure pimsm PIM-SM protocol parameters ipv6 router It configures RIPng parameters. ipv6 router It configures ospf OSPFv3 parameters. Confidential and Proprietary Information of ZTE CORPORATION...
Page 16
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Modes Prompt Admis- Command Function sion to Enter the Mode Mode Global ZXR10(config- ip vrf Configure Config- vrf)# config- VRF protocol uration uration parameters...
Page 17
Mode Mode IPSec Global ipsec ZXR10(config- It configures config- ipsec)# config- IPv6 IPSec uration uration protection. mode mode Diagno- Privi- It tests CPU ZXR10(diag)# diagnose sis mode leged utilization mode and memory utilization. Confidential and Proprietary Information of ZTE CORPORATION...
Page 18
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
................28 address-family ipv4 vrf Use this command to enter the VRF address mode configuration, Purpose or create and enter it if it does not exist. Delete this address mode with the no command. Confidential and Proprietary Information of ZTE CORPORATION...
IS-IS route priority with the no command. Router configuration Command Modes distance <distance> Syntax no distance Syntax Description <distance> Priority of the IS-IS route, range: 1~255, default: 115 This command functions on both level-1 and level-2. Instructions Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This example describes how to configure the route priority of the Example IS-IS. ZXR10(config)#router isis ZXR10(config-router)#distance 120 enable interface Use this command to start the RIP protocol on an interface.
Use this command to specify the key for the simple text authen- Purpose tication of the interface. Delete the key with the no form of this command. Interface configuration Command Modes ip rip authentication key <key> Syntax no ip rip authentication key Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Syntax Description <key> Valid key, 1~16 characters There is no key by default. Defaults � When the key is not configured with the key command, the Instructions authentication will not be performed on the interface.
RIP route update information. The RIP route information is sent and received at the same time. Defaults � This command can be used to reduce the bandwidth occupation Instructions of the network. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � The ip rip interface passive command often works with the neighbor command to have the router only send route to the specified neighbor, so as to reduce the bandwidth occupation of the network.
This example advertises the information of the subnet of the same Example network as the interface address. ZXR10(config)#interface fei_1/1 ZXR10(config-if)#ip rip only-send-subnet Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ip rip originate default route Use this command to generate a default route on the interface and Purpose force the advertisement of it. Disable this feature with the no form of this command.
If the split horizon is disabled on the serial interface (and the interface is connected Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) with the packet switching network), the split horizon must be disabled for all the routers and access servers in the related multicast groups of the network.
This command is disabled by default. Defaults � Multiple network commands can be specified. The RIP route Instructions update information can be sent or received only through these network interfaces. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � The RIP sends the update information to the specified network interface. If some network of interface is not specified, there will be no advertisement of RIP update.
RIP, and thus improves the behavior of RIP. This example sets the default metric and introduces the OSPF ex- Example ternal route with the default route. ZXR10(config)#router rip ZXR10(config-router)#default-metric 5 ZXR10(config-router)#redistribute ospf-ext Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) default-metric Related Commands route-map router rip Use this command to start the RIP routing process. Close the RIP Purpose routing process with the no form of this command.
The name of the interface to start RIP Invalid Defaults Show the information of the interface running RIP protocol. Instructions Use this command to display the RIP information of the fei_1/1 Example interface. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ZXR10#show ip rip interface fei_1/1 ip address: 10.10.30.4 receive version 1 2 send version 2 split horizon is effective show ip rip neighbors Use this command to display information about RIP neighbors.
The RIP basic timer is adjustable. Since the RIP executes the asyn- Instructions chronous routing algorithm, it is very important to keep the con- sistence of timers of all routers and access servers of the network. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Caution: If the update period is too short, it may cause congestion in the low-speed serial line. while it will not cause big problems in the high-speed serial line of the fast Ethernet.
Page 39
RIP on the interface. This example sets the version of RIP as 2. Example ZXR10(config-router)#version 2 ip rip receive version Related Commands ip rip send version Confidential and Proprietary Information of ZTE CORPORATION...
Page 40
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
............57 ip ospf message-digest-key ..........58 ip ospf mtu-ignore .............58 ip ospf network ..............59 ip ospf priority ..............60 ip ospf resync-timer............60 ip ospf retransmit-interval ..........61 ip ospf transmit-delay ............61 maximum-paths ..............62 max-metric router-lsa ............62 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10(config-router)#area 0.0.0.1 filter-list prefix zxr10 out area nssa Use this command to define an area as the NSSA area. Change Purpose the area from NSSA non-NSSA with the no form of this command. Router configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...
Page 44
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) area <area-id> nssa [no-redistribution][default-information Syntax -originate [metric <metric-value>][metric-type <type>]][no- summary] no area <area-id> nssa [no-redistribution][default-informa tion-originate][no-summary] Syntax Description <area-id> Area identifier, a decimal number...
<area-id> range <ip-address><net-mask> Syntax Description <area-id> Area identifier, a decimal number (0~4294967295) or a dotted decimal IP address. <ip-address> IP address of the summary address range, in the form of dotted decimal Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) <net-mask> Mask of the summary address range, in the form of dotted decimal advertise | advertise: summary type-3 LSA is advertised not-advertise not-advertise: summary type-3 LSA is not...
Page 47
Pay attention to the following points: i. Only some changes will take effect, as shown in the follow- ing table. command taking effect or not authentication authentication-key cost dead-interval hello-interval message-digest-key mtu-ignore network priority retransmit-interval transmit-delay Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) command taking effect or not resync_timeout passive-interface ii. The changes only take effect on the sham-link interfaces that are up. iii. If the neighbor of sham-link is already up, the changes of...
There is no host route advertised by local router in the area. Defaults � This command is supported after the platform version 4.6.02. Instructions � The no area <area-id> stub-host <ip-address> command deletes the host route advertised by local router in an area. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � If the area does not exist, it will be created automatically. This example configures the host route the router advertises as Example 10.1.1.1 and the cost value as 10.
Page 51
This example configures a virtual link between two directly-con- Example nected routers in area 1. Their router-ids are 15.15.15.15 and 16.16.16.16 respectively. ZXR10_01(config)#router ospf 1 ZXR10_01(config-router)#area 1 virtual-link 15.15.15.15 ZXR10_02(config)#router ospf 1 ZXR10_02(config-router)#area 1 virtual-link 16.16.16.16 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) auto-cost Use this command to modify the Reference Bandwidth of the OSPF Purpose process. Restore default with the no command. Router configuration Command Modes auto-cost reference-bandwidth <ref-bw>...
AS number of local BGP or when the downbit is set for Type 5 and Type 7 LSAs, and if the capability vrf-lite command is not configured in the instance, the routes will not be calculated. Otherwise, the routes will be calculated. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � For Type 3 LSA, if the downbit is set, and the capability vrf-l ite command is not configured in the instance, the routes will not be calculated.
Syntax Description <metric-value> Default cost value of the system external routes, range: 1~4294967295 By default, the metric is 1 when the BGP route is redistributed, Defaults and 20 for other routes. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � This command is supported after the platform version 4.6.02. Instructions � The configured value of this command is effective only when the user does not set the cost value of external routes.
Description internal Internal route ext1 Category 1 external routing ext2 Category 2 external routing <distance> Value of the distance, range: 1~255, default: � This command is supported after the platform version 4.6.02. Instructions Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) � When the route priority is 255, this command does not take effect. This example sets internal the dominion distance as 100. Example ZXR10(config)#router ospf 1...
� This command is supported after the platform version 4.6.03. This example sets 0.0.0.100 as router's domain-id. Example ZXR10(config)#router ospf 1 ZXR10(config-router)#distance ospf internal 100 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) router ospf x Related Commands domain-tag Use this command to specify OSPF domain tag. Purpose Router configuration Command Modes domain-tag <tag-value> Syntax Syntax Description <tag-value>...
If the OSPF protocol has been configured, it is enabled by default. Defaults This command is supported after the platform version 4.6.02. Instructions This example enables OSPF process 1. Example ZXR10(config)#enable ip ospf 1 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) disable ip ospf Related Commands fast-reroute alternate-prote ct-type Use this command to set the route backup mode. Cancel the con- Purpose figuration with the no form of this command.
Otherwise nsf will exit because of timeout before it completes, and it can not meet the non-in- terruption need. � It is suggested to prolong the time in the non-interruption for- warding environment configured with virtual link. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This example sets the longest time of nsf to 300 seconds. Example ZXR10(config)#router ospf 1 ZXR10(config-router)#grace-period 300 capability opaque Related Commands ip ospf authentication...
This example specifies an interface to support BFD function. Example ZXR10(config)#interface fei_5/1 ZXR10(config-if)#ip ospf bfd bfd-all-interface Related Commands ip ospf cost Use this command to illustrate the interface cost explicitly. Restore Purpose default with the no form of this command. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Interface configuration Command Modes ip ospf cost <cost> Syntax no ip ospf cost Syntax Description <cost> Interface cost, range: 1~65535, default: 1 The cost value uses the value of reference-bandwidth by default.
This command is supported after the platform version 4.6.02. Instructions � The hello-interval is generally set to 1/4 of the dead-interval. This example specifies the time interval of the neighbor on the Example interface to 20 seconds. ZXR10(config)#interface fei_5/1 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ZXR10(config-if)#ip ospf hello-interval 20 ip ospf dead-interval <seconds> Related Commands ip ospf message-digest-key Use this command to configure password serial number pair for the Purpose interface using message digest authentication.
It depends on the network type; the point-to-multipoint type Defaults needs configuring. This command is supported after the platform version 4.6.02. Instructions This example configures the interface pos48_5/1 as the point-to- Example point interface type. ZXR10(config)#interface pos48_5/1 ZXR10(config-if)#ip ospf network point-to-point Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ip ospf priority Use this command to set the interface priority. Make the interface Purpose restore default with the no form of this command.
This command is supported after the platform version 4.6.02. Instructions This example sets the delay for some interface to transmit a link Example status update packet as 2 seconds. ZXR10(config)#interface fei_5/1 ZXR10(config-if)#ip ospf retransmit-delay 2 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) maximum-paths Use this command to set the maximum number of routes the load Purpose balance of OSPF protocol supports. Restore default with the no form of this command.
If it is necessary to support traffic engineering in some area, this command must be configured. This example sets OSPF area 1 to support traffic engineering. Example ZXR10(config)#router ospf 1 ZXR10(config-router)#mpls traffic-eng area 1 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) mpls traffic-eng router-id Use this command to specify the router identifier of traffic engi- Purpose neering . Router configuration Command Modes mpls traffic-eng router-id <interface-name>...
ZXR10(config)#router ospf 1 ZXR10(config-router)#neighbor 10.1.1.3 network Use this command to define interfaces running OSPF protocol and Purpose area IDs of these interfaces. If the area does not exist, it will be created automatically. Confidential and Proprietary Information of ZTE CORPORATION...
Page 76
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Router configuration Command Modes network <ip-address><wildcard-mask> area <area-id> Syntax no network <ip-address><wildcard-mask> area <area-id> Syntax Description <ip-address> IP address in the form of dotted decimal <wildcard-mask>...
The router be- comes an ASBR after the use of this command. Router configuration Command Modes notify default route [always][metric <metric-value>][metric Syntax -type <type>][route-map <map-tag>] no notify default route [always][metric <metric-value>][me tric-type <type>][route-map <map-tag>] Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Syntax Description always The specification of always shows that the default route will be advertised no matter whether it exists. If there is no specification...
Use this command to control the import of eligible routes of other Purpose protocol into OSPF autonomous system. After the use of this com- mand, the router becomes an ASBR. Router configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...
Page 80
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) redistribute <protocol>[as <as-number>][peer <peer-address Syntax >][tag <tag-value>][metric <metric-value>][metric-type <typ e>][route-map <map-tag> no redistribute <protocol>[as <as-number>][peer <peer-addr ess>][tag][metric][metric-type][route-map] Syntax Description <protocol> Filtering based on protocol, value: connected,...
IP addresses. If there is no local address, the start will fail. This example configures a OSPF process with the process ID 2 and Example the VRF name vpn1. ZXR10(config)#router ospf 2 vrf vpn1 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) router-id Use this command to specify the router identifier of an OSPF Purpose process. Delete the specified router identifier with the no form of this command.
Page 83
Total number of grace LSAs Checksum Sum Sum of checksums of ASE LSAs Number of new LSAs Number of new LSAs received received Number of self originated Number of LSA local router generates LSAs Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Field Description Hold time between Time interval of SPF dispatch consecutive SPF Non-stop Forwarding Whether with the ability of nsf or not last NSF restart ago...
Path cost Type Router type of the receiving end. ABR, ASBR, or both RteType Path type. It may be the path of an internal or external area Area Area ID obtaining the path Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) show ip ospf database Use this command to display a relevant information list of the OSPF Purpose database of the specified router . Different forms of this command are used to display the link status advertisement of different sets.
Page 87
Router Link States (Area 0.0.0.1) Link ID ADV Router Seq# Checksum Link count 110.1.1.1 110.1.1.1 0x80000025 0xf8f8 168.1.1.3 168.1.1.3 0x80000005 0x70e Net Link States (Area 0.0.0.1) Link ID ADV Router Seq# Checksum 168.1.1.1 110.1.1.1 1183 0x80000002 0x9787 Confidential and Proprietary Information of ZTE CORPORATION...
Page 88
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Type-5 AS External Link States Link ID ADV Router Seq# Checksum 113.1.0.0 168.1.1.3 0x80000001 0xa0dd 111.1.0.0 110.1.1.1 0x80000001 0x4ae3 3489660928 The displayed information is described below.
Page 89
LS Seq Number Link status serial number Checksum Checksum of advertisements of the whole link status Length Length of the link status advertisement Network Mask Network mask Metric Type External type Type of service Confidential and Proprietary Information of ZTE CORPORATION...
Page 90
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Field Description Metric Cost of link status Forward Address Forwarding address. If it is 0.0.0.0, the advertisement router will be used for the forwarding.
Page 91
OSPF Router with ID (110.1.1.1) (Process ID 1) Summary Net Link States (Area 0.0.0.0) LS age: 129 Options: (No TOS-capability, No DC) LS Type: Summary Links(Network) Link State ID: 112.1.1.0 (Summary Network Number) Confidential and Proprietary Information of ZTE CORPORATION...
Page 92
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Advertising Router: 110.1.1.1 LS Seq Number: 0x80000001 Checksum: 0xd99f Length: 28 Network Mask: /24 TOS: 0 Metric: 2 The displayed information is described below.
Page 93
LS Type: Opaque Area Link Link State ID: 1.0.0.3 Opaque Type: 1 Opaque ID: 3 Advertising Router: 10.10.10.10 LS Seq Number: 0x80000001 Checksum: 0xfe8d Length: 124 Fragment number : 3 Link connected to Broadcast network Confidential and Proprietary Information of ZTE CORPORATION...
Page 94
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Link ID : 179.1.1.200 Interface Address : 179.1.1.200 Neighbor Interface Address : 0.0.0.0 Admin Metric : 1 Maximum bandwidth : 125000000 Maximum reservable bandwidth : 93750000...
Page 95
The displayed information is described below. Field Description OSPF Router with id Router ID Process ID OSPF process identifier Area database summary Statistics of the database in the area LSA Type Link status type Count Count Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Field Description Router Advertisements of router link status Network Advertisement of network link status Summary Net Advertisements of summary link status of network Summary ASBR...
Page 97
Router ID of DR Interface address Interface IP address of DR Backup Designated router Router ID of BDR (ID) Interface address Interface IP address of BDR Number of Neighbors Number of neighbors of local interface Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Field Description Number of Adjacent Number of adjacent neighbors of local neighbors interface Adjacent with neighbor Lists router ID of adjacent neighbors of local interface in sequence...
And this command supports the list show and detailed show. All modes Command Modes show ip ospf neighbor [detail][interface <interface-name>][n Syntax eighbor-id <neighbor>][process <process-id>] Syntax Description detail Shows the detailed information interface <interface- Interface Name name> Confidential and Proprietary Information of ZTE CORPORATION...
Page 100
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) neighbor-id Neighbor ID, in the form of dotted decimal <neighbor> process <process- OSPF process ID, range: 1~65535 id> This command is supported after the platform version 4.6.02.
Type, serial number and IP address of the interface of the helper State Status of the helper � This example shows the print information of the helper when nsf is run. ZXR10#show ip ospf nsf Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) OSPF Router with ID (134.1.1.201) (Process ID 200) This router is a helper of graceful restart Restarting router ID 134.1.1.200 In the area 0.0.0.0 via interface gei_7/1 134.1.1.200...
Use this command to show the information of OSPF virtual links. Purpose All modes Command Modes show ip ospf virtual-links [process <process-id>] Syntax Syntax Description process <process- OSPF process ID, range: 1~65535 id> Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This command is supported after the platform version 4.6.02. Instructions � When there is no OSPF virtual link, the following information Example will be displayed.
Use this command to specify the minimum time interval between Purpose two continual SPF computations. Use the no form of this command to make it restore the default value. Router configuration Command Modes timers spf <spf-holdtime> Syntax Confidential and Proprietary Information of ZTE CORPORATION...
Page 106
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) no timers spf Syntax Description Minimum time interval between two continual <spf-holdtime> SPF computations, unit: second, range: 1~65535, default: 1 second This command is supported after the platform version 4.6.02 .
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) show isis adjacency ............122 show isis circuits ............. 123 show isis database............124 show isis fast-reroute-topology ......... 126 show isis hostname ............127 show isis mesh-groups .............
ZXR10(config-router)#authentication-type TEXT ZXR10(config-router)#authentication-type TEXT level-1 ZXR10(config-router)#authentication-type TEXT level-2 default-information originate Use this command to configure the advertisement policy of the Purpose default route. Delete the configured policy with the no form of this command. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Router configuration Command Modes default-information originate [always][metric <metric-value Syntax >][metric-type <type>][level-1 | level-1-2 | level-2] no default-information originate Syntax Description always No matter whether there is a default route in...
This command acts on both level-1 and level-2 at the same time. Instructions This example specifies the priority of IS-IS routes. Example ZXR10(config)#router isis ZXR10(config-router)#distance 120 enable Use this command to restart IS-IS instances. Purpose Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Router configuration Command Modes enable Syntax � This command is supported after the platform version 4.6.02. Instructions � After IS-IS instances are disabled by the disable command, this command can be used to make IS-IS instances go on runnning.
ZXR10(config)#router isis ZXR10(config-router)#hello padding point-to-point hostname Use this command to configure the hostname function of IS-IS. Purpose Delete the configuration with no form of this command. Router configuration Command Modes hostname {dynamic} Syntax Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Syntax Description dynamic The hostname of system is obtained dynamically This command is supported after the platform version 4.8.02. Instructions This example sets the system hostname is obtained dynamically.
If level-1 or level-2 is not specified, this command acts at level-1 and level-2 at the same time. This example sets the authentication type of IS-IS hello PDUs. Example ZXR10(config)#interface fei_1/1 ZXR10(config-intf)#isis authentication-type MD5 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ZXR10(config-intf)#isis authentication-type MD5 level-1 ZXR10(config-intf)#isis authentication-type MD5 level-2 ZXR10(config-intf)#isis authentication-type TEXT level-1 ZXR10(config-intf)#isis authentication-type TEXT level-2 isis bfd-enable Use this command to enable the bfd function of IS-IS. Disable the Purpose function with no form of this command.
If the router is a DIS, it sends hello packets every 3 seconds Instructions regardless of the configuration. � The parameter of level is not valid on point-to-point mode sim- ulated by LAN. Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This example describes sets the time interval of sending Hello Example packets. ZXR10(config)#interface fei_1/1 ZXR10(config-intf)#isis hello-interval 5 ZXR10(config-intf)#isis hello-interval 5 level-1 ZXR10(config-intf)#isis hello-interval 5 level-2...
<metric-value>[level-1 | level-2] Syntax no isis ipv6 metric [level-1 | level-2] Syntax Description <metric-value> Metric value of the interface, range: 0~16777214 level-1 The router is in area Level-1 level-2 The router is in area Level-2 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) This example sets the IPv6 metric value of interface fei_1/1 as 66. Example ZXR10(config)#interface fei_1/1 ZXR10(config-intf)#isis ipv6 metric 66 ZXR10(config-intf)#isis ipv6 metric 66 level-1...
0~63. If it is the metric-style wide mode, the range of the <metric-value> will be 0~426142864. This example configures the metric value of this interface. Example ZXR10(config)#interface fei_1/1 ZXR10(config-intf)#isis metric 20 ZXR10(config-intf)#isis metric 20 level-1 ZXR10(config-intf)#isis metric 20 level-2 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) isis network point-to-point Use this command to configure isis protocol LAN to simulate point- Purpose to-point function. Use no to delete this configuration. Interface configuration mode...
Time of t1 timer <retry-timers> Retry times of t1 timer, default: 3 <interval> Time interval in seconds, range: 1~65535, default: 3 seconds level-1 The router is in area Level-1 level-2 The router is in area Level-2 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) If level-1 or level-2 is not specified, this command acts at both Defaults level-1 and level-2 at the same time. � On broadcast multi-access networks, if local router is elected...
This command can make the size of LSP packets in the range of 512 and 7680. It is not recommended to use this com- mand except special situation. This example sets LSP-mtu as 512 bytes. Example ZXR10(config)#router isis ZXR10(config-router)#lsp-mtu 512 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) max-lsp-lifetime Use this command to set the maximum time that link-state packets Purpose persist without being refreshed. Restore the default time with the no form of this command.
The configuration of IS-IS traffic engineering needs to first config- Instructions ure the metric-style as wide. This example configures IS-IS level-1 starting traffic engineering Example and sets the router-id. ZXR10(config)#router isis ZXR10(config-router)#mpls traffic-eng level-1 ZXR10(config-router)#mpls traffic-eng router-id loopback1 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) passive-interface Use this command to configure an interface as a passive interface. Purpose After that, the interface cannot send Hello packets, receive any IS-IS packet or establish adjacent relationship with other routers.
If a router supports some kind of is-type, there must be the neigh- Instructions borhood supporting this kind of is-type to complete the synchro- nization of the database. This example describes enables the restart function. Example Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) ZXR10(config)#router isis ZXR10(config-router)#restart enable ZXR10(config-router)#restart t2-timer 60 ZXR10(config-router)#restart t3-timer manual 40 router isis Use this command to configure the IS-IS route protocol process. Purpose Close the IS-IS route protocol process with the no form of this command.
This example describes how to set the IS-IS overload bit. Example ZXR10(config)#router isis ZXR10(config-router)#set-overload-bit Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) show isis adjacency Use this command to display information about the current neigh- Purpose bor. All modes Command Modes show isis adjacency [level-1 | level-2| up_time {level-1 | Syntax level-2}][vrf <vrf-name>]...
Level-1 Metric:10 Priority:64 LAN ID: 12A4.5678.9122.01-01 Number of active adjacencies:1 Next hello in 9 seconds Level-2 Metric:10 Priority:64 Circuit ID: 1200.2222.2222.02-02 Number of active adjacencies:1 Next hello in 7 seconds Interface: pos_1/1 Encapsulation:PPP Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Circuit Type:Level-1-2 Level-1 Metric:10 Level-2 Metric:10 Circuit ID: 0000.400a.0a05.02-02 active Adj state:level-1-2 Next hello in seconds:5 The description of the displayed fields is shown below.
Page 135
LSP ID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL 1921.6800.5080-00-00 0x00000022 0x34E3 1078 0/0/0 NLPID:0xcc Area Address:00.0001 Metric 10 IS neighbor 1223.2232.1111-01 Metric 10 IS neighbor 1001.AC32.11D1-02 3421.68AC.0010-00-00 0x00000022 0x34E3 1078 0/0/0 Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) NLPID:0xcc Area Address:00.0001 Metric 10 IS neighbor 1223.0755.1111-01 Metric 10 IS neighbor 1001.AC32.0063-02 The displayed information is described below. Field Description IS neighbor IS neighbor...
IS-IS mesh group [blocked]:fei_1/1 show isis nsf Use this command to display parameters of status related with Purpose current graceful restart of IS-IS. All modes Command Modes show isis nsf vrf <vrf-name> Syntax Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) Syntax Description vrf <vrf-name> VRF name, 1~16 characters When routers are gracefully restarting, this command can be used Instructions to look over parameters of relevant status.
ZXR10(config-router)#spf-interval 10 level-2 summary-address Use this command to specify the summary address of IS-IS. Delete Purpose the summary address of the specified level with the no form of this command. Router configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...
All manuals and user guides at all-guides.com ZXR10 8900 Series Command Reference (IP Routing Volume I) summary-address <ip-address><net-mask><metric-value>[l Syntax evel-1 | level-1-2 | level-2] no summary-address <ip-address><net-mask> Syntax Description <ip-address> Summary address allocated to a certain range of addresses, in the dotted decimal format <net-mask>...
Page 141
To change the system identifier, use the no form of this com- mand first to delete the old one. This example describes how to set the system identifier of IS-IS. Example ZXR10(config)#router isis ZXR10(config-router)#system-id 1111.1111.1111 ZXR10(config-router)#system-id 1111.1111.1111 range 32 Confidential and Proprietary Information of ZTE CORPORATION...