Zte ZXR10 Command Manual
  1. Manuals
  2. Brands
  3. Zte Manuals
  4. Network Router
  5. ZXR10 3800-8
  6. Command manual

Zte ZXR10 Command Manual

Router/ethernet switch
Hide thumbs Also See for ZXR10:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Command Manual, Instruction Manual
ZXR10
Router/Ethernet Switch
Command Manual (MPLS Volume)
Version 4.8.22
ZTE CORPORATION
ZTE Plaza, Keji Road South,
Hi-Tech Industrial Park,
Nanshan District, Shenzhen,
P. R. China
518057
Tel: (86) 755 26771900
Fax: (86) 755 26770801
URL: http://ensupport.zte.com.cn
E-mail: support@zte.com.cn

Advertisement

Table of Contents
loading

Related Manuals for Zte ZXR10

Summary of Contents for Zte ZXR10

  • Page 1 ZXR10 Router/Ethernet Switch Command Manual (MPLS Volume) Version 4.8.22 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn...
  • Page 2 The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.

  • Page 3: Table Of Contents

    About This Manual..........i Command Introduction ........1 Manual Use Guide............1 Description of Man-Machine Commands ......1 Auxiliary Function ............2 Command Mode ............. 3 MPLS LDP Configuration ........7 clear mpls ldp ..............8 clear mpls ldp dampening ..........8 clear mpls ldp flap ............
  • Page 4 show mpls ldp backoff ............33 show mpls ldp bindings ..........34 show mpls ldp dampening summary.........36 show mpls ldp flap-statistics summary ......37 show mpls ldp discovery ..........38 show mpls interface ............39 show mpls ldp neighbor..........39 show mpls ldp graceful-restart ........41 show mpls ldp parameters ..........42 MPLS BGP VPN Configuration ......
  • Page 5 pwtype.................58 show mac-filter .............59 show mac-table.............59 show mpls l2transport vc vpls .........60 show mpls l2transport vpn summary ........62 show vfi ...............62 show vfi brief ..............63 stp-tunnel enable ............64 vcid ................64 vpls apply-mac-filter ............65 vfi ................66 vfi mspw ..............66 vpls mac-filter...............67 vlan range ..............68 xconnect vfi ..............68 MPLS Traffic Engineering Configuration...
  • Page 6 mpls traffic-eng ds-te.............81 mpls traffic-eng ds-te bc-mode........81 mpls traffic-eng ds-te exp-maps ........82 mpls traffic-eng ds-te te-class .........82 mpls traffic-eng signaling advertise implicit-null....83 mpls traffic-eng tunnels(Global Configuration) ....84 mpls traffic-eng tunnels(Interface Configuration) ....84 show ip rsvp authentication ..........85 show ip explicit-path ............86 show ip rsvp hello graceful-restart ........87 show ip rsvp refresh parameter ........87 show mpls traffic-eng autoroute ........88...

  • Page 7: About This Manual

    Purpose operation of ZXR10 router and Ethernet switch. This manual is intended for engineers and technicians who perform Intended Audience operation activities on ZXR10 router and Ethernet switch. This manual contains the following chapters: What Is in This Manual Chapter...
  • Page 8 ZXR10 Command Manual (MPLS Volume) � ZXR10 Router/Ethernet Switch Command Manual (QoS Vol- ume) � ZXR10 Router/Ethernet Switch Command Manual (Security Volume) � ZXR10 Router/Ethernet Switch Command Manual (Network Management Volume) � ZXR10 Router/Ethernet Switch Command Manual (Multicast Volume) �...

  • Page 9: Command Introduction

    To search a command, do as follows: 1. Find the desired command by referring to ZXR10 Router/Eth- ernet Switch Command Manual — Command Index. 2. Find command details by the volume, chapter/section and page of the obtained command.

  • Page 10: Auxiliary Function

    Do not describe the history command if this entry does not exist. Auxiliary Function The auxiliary function for ZXR10 devices is as follows. 1. In any command mode, enter a question mark (?) after the DOS prompt of the system, a list of available commands in the command mode will be displayed.

  • Page 11: Command Mode

    ENTER. The ^ is below the first character of the input incorrect command, keyword or parameter. 3. ZXR10 router/Ethernet switch allows the command or key- word to be abbreviated into a character or character string that uniquely identifies this command or keyword. For example, the show command can be abbreviated to sh or sho.
  • Page 12 <1~64 mode mode serial port >(GAR) and telnet connection Layer ZXR10(config- Global acl link Defines layer 2 ACL link-acl)# config- 2 ACL rule config- uration uration mode mode Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 13 Configures ospf OSPFv3 parameters ZXR10(config- Global ip vrf Configures config- vrf)# config- uration uration parameters mode mode VFI con- Global ZXR10(config- Configures figu- config- vfi)# VPLS related ration uration parameters mode mode Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 14 IPSec ZXR10(config- Global ipsec Configures config- config- ipsec)# IPv6 IPSec uration uration protection mode mode Diagno- Privi- diagnose Tests CPU ZXR10(diag)# sis mode leged and memory mode usage Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 15: Mpls Ldp Configuration

    .........37 show mpls ldp discovery.............38 show mpls interface ............39 show mpls ldp neighbor............39 show mpls ldp graceful-restart ..........41 show mpls ldp parameters ..........42 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 16: Clear Mpls Ldp

    LSP will be cleared. If this LSP is suppressed, the router will unsuppress it. � This example describes how to reset LDP dampening informa- Example tion. ZXR10#clear mpls ldp dampening Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 17: Clear Mpls Ldp Flap

    ZXR10#clear mpls ldp flap � This example describes how to reset the flapping statistic in- formation of a LSP. ZXR10#clear mpls ldp flap 100.1.1.1 32 mpls ip (Global Configuration) Use this command to enable LDP to establish an LSP along a com- Purpose mon hop-by-hop routing path.

  • Page 18: Mpls Ip(Interface Configuration)

    Global configuration Command Modes mpls label range <min-label><max-label> Syntax no mpls label range Syntax Description <min-label> Minimal available label, range: 16~1048575 <max-label> Maximal available label, range: 16~1048575 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 19: Mpls Ldp Access-Fec

    VPN routes. The mpls ldp access-fec host-route-only command can effectively decrease the number of FECs. � This command does not collide with the above two policies. By default, FEC is not created for route networks obtained by Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 20: Mpls Ldp Advertise-Labels

    [for <prefix-access-list>[to <pee r-access-list>]] Syntax Description for <prefix-access-li Destination network label to be advertised, st> basic ACL: 1~99 and 1000~1499 to <peer-access-list> Advertises which labels to which neighbors, basic ACL: 1~99 and 1000~1499 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 21 Otherwidse, it could not take effect immediately. Do not use this command frequently. 1. This example describes how to forbid the router from advertis- Example ing any label to any neighbor. ZXR10(config)#no mpls ldp advertise-labels Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 22: Mpls Ldp Advertise-Labels Old-Style

    ZXR10(config)#ip access-list standard 20 ZXR10(config-ext-nacl)#permit 35.0.0.0 0.255.255.255 ZXR10(config-ext-nacl)#exit ZXR10(config)#ip access-list standard 21 ZXR10(config-ext-nacl)#permit 133.0.0.33 0.0.0.0 ZXR10(config-ext-nacl)#exit ZXR10(config)#mpls ldp advertise-labels for 10 to 11 ZXR10(config)#mpls ldp advertise-labels for 20 to 21 mpls ldp advertise-labels old-style Related Commands mpls ldp advertise-labels old-style Use this command to allow the <prefix-access-list>...

  • Page 23: Mpls Ldp Backoff

    This example describes how to set the initial backoff time as 30 Example seconds and the maximum backoff time as 240 seconds. ZXR10(config)#mpls ldp backoff 30 240 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 24: Mpls Ldp Bfd

    This command triggers the creation of LSP BFD, and specifies the Instructions network address of LSP. This example describes how to triggers the creation of BFD of LSP Example 2.2.2.2. ZXR10(config)#mpls ldp bfd 2.2.2.2 32 interval 50 min_rx 50 multiplier 3 show bfd nei ldp-lsp Related Commands mpls ldp dampening...

  • Page 25: Mpls Ldp Dampening-Acl

    By default, LDP records the dampening information for flapping destination networks. By default, LDP records the dampening information for flapping Instructions destination networks. However, there are so many networks in Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 26: Mpls Ldp Discovery Hello

    This example describes how to set the status holdtime as 100 sec- Example onds and the interval for sending hello messages as 20 seconds. ZXR10(config)#mpls ldp discovery hello holdtime 100 ZXR10(config)#mpls ldp discovery hello interval 20 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 27: Mpls Ldp Discovery Targeted-Hello

    This example describes how to set the status holdtime as 100 sec- Example onds and the interval for sending hello messages as 20 seconds. ZXR10(config)#mpls ldp discovery targeted-hello holdtime 100 ZXR10(config)#mpls ldp discovery targeted-hello interval 20 show mpls ldp parameter...
  • Page 28 If the configuration of the transmission address is changed during the precess of the running of the interface, ZXR10 router will delete the current adjacency relationship on the interface. If there is no other adjacent relationship maintaining the session maintained by the current adjacent relationship on the interface (multiple links do not exist), the session will be closed.

  • Page 29: Mpls Ldp Egress

    <nexthop-access-list> , the LDP will allocate a popup label to it. The policy takes effect only on the refreshed FECs after the config- uration and does not reallocate labels to the existing FECs. There- Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 30: Mpls Ldp Enable Connect-With-Dod

    To disable this feature, use the no form of this command. Global configuration Command Modes mpls ldp explicit-null [for <prefix-access-list>][to <peer-acce Syntax ss-list>] no mpls ldp explicit-null Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 31: Mpls Ldp Graceful-Restart

    <peer-access-list> Specifies which neighbors that the explicit null labels replaces implicit ones is advertised to, range: 1~99 By default, ZXR10 advertises directly connected networks to all Defaults neighbors by means of implicit null labels. � By default, ZXR10 advertises directly connected networks to Instructions all neighbors by means of implicit null labels.

  • Page 32: Mpls Ldp Holdtime

    GR function. The value of neighbor- liveness is configured as 30 seconds, and the value of max-recovery is configured as 40 sec- onds. ZXR10(config)#mpls ldp graceful-restart ZXR10(config)#mpls ldp graceful-restart timer neighbor-liveness 30 ZXR10(config)#mpls ldp graceful-restart timer max-recovery 40 show mpls ldp graceful-restart Related...

  • Page 33: Mpls Ldp Neighbor Password

    MD5 key used for establishing TCP connection <password> with the neighbor, 3~80 characters By default, there is no MD5 option in ZXR10 LDP session. Defaults MD5 authentication can be introduced between LDP peers to au- Instructions thenticate each TCP section. To enable MD5 authentication, both LSRs should be configured with authentication and use the same key;...

  • Page 34: Mpls Ldp Router-Id

    LDP (if the interface is in the UP state) force Immediately changes the router identifier By default, the election rules of LDP router identifier on ZXR10 are Defaults as follows: 1. Firstly, if the mpls ldp router-id command is used to desig-...

  • Page 35: Mpls Ldp Style

    LDP PDU packet (including TCP and UDP packets) is received. This example describes how to enable the new keepalive mecha- Example nism of LDP sessions. ZXR10(config)#mpls ldp style Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 36: Mpls Ldp Target-Session

    � If there is the tunnel parameter, MPLS labels are allocated by the specified tunnel. If there is no tunnel parameter, MPLS labels are allocated by LDP. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 37: Show Mpls Forwarding-Table

    101.1.1.2 The displayed field descriptions are shown below. Field Description InLabel Incoming label OutLabel Outgoing label Dest Destination network or destination host address Pfxlen Prefix length Interface Outgoing interface NextHop Next hop Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 38: Show Mpls L2Transport Binding

    Field Description Destination Address Peer address VC ID ID of VC Local Label Locally assigned label Cbit Flag of control field VC Type Type of VC GroupID Group ID information Maximum transmission unit Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 39: Show Mpls L2Transport Vc

    This command is supported after the platform version 4.6.02. Instructions All the current VCs are displayed if there is no parameter specified. This command is provided only on ZXR10 GER and ZXR10 T64E/T128. 1. This example describes how to show all the current VCs.
  • Page 40 3.4.5.6 4. This example describes how to show detailed information of the VC with VCID as 201. ZXR10#show mpls l2transport vc vcid 201 detail LocalInterface: fei_1/2.1 up, lineProtocol up, localCircuit VlanID: 201 up Destination address: 3.4.5.6, VC ID: 201, VC status: up...

  • Page 41: Show Mpls Label Range

    User EXEC and privileged EXEC Command Modes show mpls ldp backoff Syntax This example shows the output of the show mpls ldp backoff Example command. ZXR10#show mpls ldp backoff Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 42: Show Mpls Ldp Bindings

    Shows the entries matching the label value <label>[<label>] allocated by neighbor with the label range specified by the parameter label – label, range: 0~1048575 summary Shows the summary of all entries and downstream bindings in the LDP FEC table Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 43 66.66.0.66:0, label: 24 2. This example describes how to show label bindings of the net- work 166.0.0.0 and its subnets learned by the LSR 144.0.0.44. ZXR10#show mpls ldp bindings 166.0.0.0 8 longer-prefixes neighbor 144.0.0.44 166.44.0.0/255.255.0.0 local binding: label: 29 remote binding: lsr: 144.0.0.44:0, label: 25...

  • Page 44: Show Mpls Ldp Dampening Summary

    Example covery. ZXR10#show mpls ldp dampening summary Damp LSPS of ldp: status codes: d damped InLable OutLable Network From Reuse Penalty 25.25.25.25/32 20.1.1.25 25.25.25.25:0 00:00:01 1729 The displayed field descriptions are shown below. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 45: Show Mpls Ldp Flap-Statistics Summary

    LSP is suppressed now. * implies the current lsp exists in history link list, and LDP is valid. h implies the current lsp exists in history link list, and ldp is invalid Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 46: Show Mpls Ldp Discovery

    Description Local LDP Identifier Local LDP identifier Interface List of interfaces acting the LDP discovery Xmit Indicates that the interface is sending hello message Recv Indicates that the interface is receiving hello message Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 47: Show Mpls Interface

    Reserved version to be upgraded Operational Interface state show mpls ldp neighbor Use this command to show information about LDP sessions. Purpose User EXEC and privileged EXEC Command Modes show mpls ldp neighbor [<neighbor>|<interface-name>][det Syntax ail] Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 48 Local LDP Ident LDP identifier of the session of local router TCP connection TCP connection that supports the session State Session state Msgs sent/rcvd Number of LDP messages received and sent through the session Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 49: Show Mpls Ldp Graceful-Restart

    LDP GR. ZXR10#show mpls ldp graceful-restart LDP Graceful Restart is enabled Neighbor Liveness Timer: 30 seconds Max Recovery Timer: 40 seconds Graceful Restart-enabled Sessions: The displayed field descriptions are shown below. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 50: Show Mpls Ldp Parameters

    This example describes how to show the current parameter infor- Example mation about LDP. ZXR10#show mpls ldp parameters Protocol version: 1 Downstream label pool: min label: 16; max label: 100000 Session hold time: 180 sec; keep alive interval: 60 sec Discovery hello: holdtime: 15 sec;...

  • Page 51: Mpls Bgp Vpn Configuration

    Use this command to set the description about a VRF. Delete the Purpose description with the no form of this command. VRF configuration Command Modes description <string> Syntax no description Syntax Description <string> Description about the VRF, a string of 1~16 characters Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 52: Export Map

    There is no route map related to the VRF by default. Defaults This example describes how to set the import route map related Example to the VPN named zte. The name of the route map is inmap. ZXR10(config)#ip vrf zte ZXR10(config-vrf)#import map inmap Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 53: Ip Vrf

    Instructions face is bounded with the VPN. � Enter the VRF configuration mode after the command is exe- cuted successfully. This example describes how to configure a VPN named zte. Example ZXR10(config)#ip vrf zte ZXR10(config-vrf)# ip vrf forwarding Use this command to associate an interface with a VRF. Cancel the Purpose association with the no form of this command.

  • Page 54: Maximum Routes

    Port monitor session number, range: 1~8 Only switches support port monitor configuration. Because ZXR10 Instructions 5900 only support one session temporarily, this command does not make sense for ZXR10 5900 and it has been deleted. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 55: Monitor Session Destination

    There is no route distinguisher by default. Defaults The VRF does not take effect until the route distinguisher is con- Instructions figured. This example describes how to configure an route distinguisher for Examples the VPN named zte. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 56: Route-Target

    There is no route-target extended community attribute related to Defaults the VRF by default. This example describes how to configure the route-target extended Example community attribute for the VPN named zte. ZXR10(config)#ip vrf zte ZXR10(config-vrf)#route-target import 1:1 ZXR10(config-vrf)#route-target export 1:1 show ip protocol routing vrf...

  • Page 57: Show Ip Protocol Routing Vrf-Summary

    Use this command to show the route information of VPN instances. Purpose All modes Command Modes show ip route vpn Syntax This example describes how to show the route information of all Example VPN instances. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 58: Show Ip Route Vrf

    ZXR10#show ip route vrf-summary zte show ip vrf Use this command to show the VRF configuration information. Purpose All modes Command Modes show ip vrf [brief | detail | interfaces | summary][<vrf-nam Syntax e>] Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 59: Show Monitor Session

    Interface configuration Command Modes tunnel checksum Syntax no tunnel checksum This example describes how to configure local GRE tunnel to enable Example the tunnel checksum option. ZXR10(config)#interface fei_5/1 ZXR10(config-if)#tunnel checksum Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 60: Tunnel Destination

    Use this command to configure the tunnel mode. Cancel the con- Purpose figuration with the no form of this command. Interface configuration Command Modes tunnel mode {gre ip | mpls traffic-eng | ipv6ip [6to4]|ipip Syntax no tunnel mode Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 61: Tunnel Sequence

    Configures the tunnel as 4in6 tunnel (provided only in the project supporting IPv6) ZXR10 5900 series support 6in4 and 6to4 tunnels only. The other Instructions types of routers and switches supports all of kinds of tunnels. This example describes how to configure the tunnel as GRE tunnel.
  • Page 62 ZXR10 Command Manual (MPLS Volume) This command is expressed before the platform version v4.6.01. The keywords ipv4 and ipv6 are provided after the platform ver- sion v4.6.01. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 63: Vpls Configuration

    VFI name that VPLS example(to clear flow statistic) corresponds to Clera VPLS flow statistics information by force. Instructions Only ZXR10 6900 and ZXR10 8900 support this command. This example describes how to clear vfi1 and all vfi flow. Example ZXR10#clear flowstat vpls vfi vfi1...

  • Page 64: Clear Flowstat Vpws

    Use this command to force to clear the MAC address forwarding Instructions table of the VPLS instead of clear the MAC address by aging it. � This command is provided only for ZXR10 GER and ZXR10 T64E/T128. This example describes how to clear the MAC address table of vfi1. Example...

  • Page 65: Peer

    PE. The spoke type is used for VPLS hierarchy and cross-domain. 1. This example describes how to execute the peer command in Example VFI configuration mode on the PE. ZXR10(config)#vfi vfi1 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 66: Pwtype

    1. This example describes how to configure the pseudo-wire type Example in VFI configuration mode on the PE. ZXR10(config)#vfi vfi1 ZXR10(config-vfi)#pwtype Ethernet Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 67: Show Mac-Filter

    <rule_number> Syntax Syntax Description <rule_number> Rule number for MAC filtering, range: 0~127 This command is supported by ZXR10 T64E/T128. Instructions This example describes how to show detaiedl information about Example the filtering of some VPLS MAC . ZXR10(config)#show mac-filter 1...

  • Page 68: Show Mpls L2Transport Vc Vpls

    Syntax Description <vfi-name> Name of the Virtual Forwarding Instance (VFI) in the VPLS This command is provided only for ZXR10 GER and ZXR10 Instructions T64E/T128. This example describes how to show the MAC table of the vfi1. Example ZXR10#show mac-table vfi1 peer-address outIntLab outExtLab outInterface type 0000.0000.2009 Local...
  • Page 69 6.6.6.6 2. This example describes how to show detailed VPLS information of the VFI named 1. ZXR10#show mpls l2transport vc vpls vfi 1 detail Local interface: VFI 1 up Destination address: 7.7.7.7, VC ID: 1, VC status: up Tunnel label:...

  • Page 70: Show Mpls L2Transport Vpn Summary

    Syntax Description <vfi-name> Designated virtual forwarding instance (VFI) name in VPLS This command is provided only for ZXR10 GER, ZXR10 T64E/T128, Instructions and ZXR10 6900/8900. This example describes how to show detailed information of a VPLS Example virtual forwarding instance (VFI).

  • Page 71: Show Vfi Brief

    User EXEC and privileged EXEC Command Modes show vfi brief Syntax This command is provided only for the ZXR10 GER and ZXR10 Instructions T64E/T128. This example describes how to show the current VPLS virtual for- Example warding instance (VFI) table.

  • Page 72: Stp-Tunnel Enable

    If VPLS instances on two PE routers belong to the same VPLS, a pseudo wire (PW) must be established between the PEs for com- munication of these VPLS instances. The pseudo wire (PW) is es- Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 73: Vpls Apply-Mac-Filter

    This example describes how to apply MAC filter rule to a virtual Example forwarding instance (VFI) member on the PE. ZXR10(config)#vfi vfi1 ZXR10(config-vfi)#vpls apply-mac-filter 1 global no vfi Related Commands vcid pwtype peer no peer vpls mac-filter Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 74: Vfi

    PW forwarding. This con- figuration allows the configuration instance to act as a forward- ing relaying node of the static multi-hop pseudo wire (PW). Use this command to enter VFI MSPW configuration mode. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 75: Vpls Mac-Filter

    � Use this command to implement VPLS MAC filtering. This example describes how to configure the VPLS instance name Example on the PE. ZXR10(config)#vpls mac-filter-rule 1 ZXR10(config)#vpls mac-filter-rule 1 single 1 0001.0002.0003 no vfi Related Commands pwtype peer no peer...

  • Page 76: Vlan Range

    Upper limit of the VLAN range Three VLAN ranges can be configured on local interface once. Instructions This command is provided only for ZXR10 GER and ZXR10 T64E/T128. This example describes how to configure a VLAN range in PE VFI Example interface configuration mode.

  • Page 77: Mpls Traffic Engineering Configuration

    ........89 show mpls traffic-eng interface detail ........90 show mpls traffic-eng tunnels..........91 show mpls traffic-eng tunnels remote-tunnel......93 tunnel mpls oam back-up-lsp tunnel ........94 tunnel mpls oam tunnelid ...........94 tunnel mpls oam type ............95 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 78: Clear Ip Rsvp Authentication

    {name <name>| identifier <identifier>} next Syntax -address <A.B.C.D>{loose | strict} no ip explicit-path {name <name>| identifier <identifier>} Syntax Description name <name> Explicit path name, 1~16 characters identifier <identifi Explicit path identifier, range: 1~65535 er> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 79: Ip Rsvp Authentication

    This example describes how to configure a explict path named test. Example The next hop is a loose path 100.1.1.1. ZXR10(config)#ip explicit-path name test next-address 100.1.1.1 loose ip rsvp authentication Use this command to enable RSVP authentication on the interface.

  • Page 80: Ip Rsvp Authentication Challenge-Imp

    <lifetime> Syntax no ip rsvp authentication lifetime Syntax Description <lifetime> Life time of the authentication key in seconds, range: 1~86400 The default lifetime is 1800 seconds (30 minutes). Defaults Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 81: Ip Rsvp Authentication Key Passphrase

    This example describes how to configure the RSVP authentication Example key as zxr102008. ZXR10(config)#interface fei_1/1 ZXR10(config-if)#ip rsvp authentication key passphrase zxr102008 ip rsvp authentication type Use this command to configure RSVP authentication type (MD5 or Purpose SHA1). Restore the default type MD5 with the no form of this command.

  • Page 82: Ip Rsvp Authentication Window-Size

    ZXR10(config-if)#ip rsvp authentication window－size 5 ip rsvp bandwidth Use this command to configure the TE bandwidth in interface con- Purpose figuration mode on the interface. Restore default with the no form of this command. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 83: Ip Rsvp Bfd

    Forwarding Detection (BFD) sessions are not established even if this command is configured. This example describes how to configure Bidirectional Forwarding Example Detection (BFD) function on the interface. ZXR10(config)#interface fei_1/1 ZXR10(config-if)#ip rsvp bfd Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 84: Ip Rsvp Signalling Hello Graceful-Restart

    10~30000 The default value is 10000 milliseconds by default. Defaults This example describes how to configure the Hello refresh interval Example as 3000 milliseconds. ZXR10(config)#ip rsvp signalling hello graceful-restart refresh interval 3000 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 85: Ip Rsvp Signalling Hello Graceful-Restart Refresh Misses

    The default missing number is 4. Defaults This example describes how to configure the number of missing Example graceful restart hello packets as 3. ZXR10(config)# ip rsvp signalling hello graceful-restart refresh misses 3 ip rsvp signalling hello graceful-restart timers recovery-time...

  • Page 86: Ip Rsvp Signalling Hello Graceful-Restart Timers Restart-Time

    Use this command to configure the time interval of sending refresh Purpose packets. Restore the default setting with the no form of this com- mand. Global configuration Command Modes ip rsvp signalling refresh interval <interval-value> Syntax no ip rsvp signalling refresh interval Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 87: Ip Rsvp Signalling Refresh Misses

    5000~4294967295 This exmaple describes how to configure the time interval of send- Example ing refresh packets as 60000 milliseconds. ZXR10(config)#ip rsvp signalling refresh interval 60000 ip rsvp signalling refresh misses Use this command to configure the number of missing refresh Purpose packets.

  • Page 88: Mpls Oam(Interface Configuration)

    <tunnel-id> ingress <lsr-id> egress<ls r-id> MPLS OAM is disabled by default. Defaults Syntax Description <tunnel-id> Static lsp mark ingress <lsr-id> Static lsp ingress router-id egress <lsr-id> Static lsp egress router-id In-port name in-port <if-name> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 89: Mpls Traffic-Eng Ds-Te

    This example describes how to set tunnel1, ingress ip address Example 1.1.1.1, egress ip address 2.2.2.2, in-label 17, in-port gei_1/2, out-label 18, out-port gei_1/3, next-hop 20.20.20.1. ZXR10(config-if)#mpls static tunnel 1 ingress 1.1.1.1 egress 2.2.2.2 in-port gei_1/2 in-label 17 out-port gei_1/3 out-label 18 next-hop 20.20.20.1 mpls traffic-eng ds-te...

  • Page 90: Mpls Traffic-Eng Ds-Te Exp-Maps

    Instructions In this example, the exp-map map is the combination of the cor- Example responding tunnel 1 and ct0 of exp1. ZXR10(config)# mpls traffic-eng ds-te exp-maps exp 1 output tunnel1 classtype 0 mpls traffic-eng ds-te te-class Use this command to configure the TE-CLASS mapping relationship Purpose in global configuration mode.

  • Page 91: Mpls Traffic-Eng Signaling Advertise Implicit-Null

    This example describes how to configure the TC-CLASS mapping Example named Teclass1, which is the combination of the corresponding ct0 and the priority 1. ZXR10(config)# mpls traffic-eng ds-te te-classes te-class 1 class-type 0 priority 1 mpls traffic-eng signaling advertise implicit-null Use this command to configure the RSVP implicit-null function.

  • Page 92: Mpls Traffic-Eng Tunnels(Global Configuration)

    ZXR10(config)#mpls traffic-eng tunnels mpls traffic-eng tunnels(Interface Configuration) Use this command to enable MPLS traffic engineering signalling Purpose on a interface. Disable the function with the no form of this com- mand. Interface configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 93: Show Ip Rsvp Authentication

    0x1e2868f0e Challenge: Configured Windowsize: 5 Integriy HF flag: Set Sequence window: 0x1e2868f0b 0x1e2868f0c 0x1e2868f0d 0x1e2868f0e The descriptions of the displayed information are shown below. Field Description Interface Corresponding interface name of the SA Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 94: Show Ip Explicit-Path

    The descriptions of the displayed information are shown below. Field Description PATH Name of the path or number of flags 1. next-address First IP address in the path 2. next-address Second IP address in the path Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 95: Show Ip Rsvp Hello Graceful-Restart

    The following contents will be shown after using this command. Example ZXR10#show ip rsvp refresh parameter RSVP-TE: Enabled RSVP signalling refresh interval: 30000 msecs RSVP signalling refresh misses The descriptions of the displayed information are shown below. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 96: Show Mpls Traffic-Eng Autoroute

    Use this command to show exp-map mapping relationship. Purpose All modes except user EXEC Command Modes show mpls traffic-eng ds-te exp-map Syntax This command is supported after the platform version 4.8.21. Instructions Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 97: Show Mpls Traffic-Eng Ds-Te Te-Class

    ZXR10#show mpls traffic-eng ds-te te-class TeclassId CType Priority unused unused unused unused The descriptions of the displayed information are shown below. Field Description TeclassID TE-CLASS value Ctype Ctype corresponding to the tunnel Priority Tunnel priority Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 98: Show Mpls Traffic-Eng Interface Detail

    This command is supported after the platform version 4.8.21. Instructions The following contents will be shown after using this command. Example (The data below are for reference only): ZXR10#show mpls traffic-eng interface detail fei_1/1 fei_1/1: Bandwidth: Curr allocated: 0K bits/sec Max. allowed (total): 75000K bits/sec Max.

  • Page 99: Show Mpls Traffic-Eng Tunnels

    RSVP protocol state Forwarding Forwarding state TUNNEL NAME Tunnel name DESTINATION Destination address of the tunnel UP IF Uplink interface of the tunnel DOWN IF Downlink interface of the tunnel STATE/PROT Tunnel administration/running state Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 100 Whether the tunnel supports fast reroute: enable/disable InLabel Incoming label and the interface of the tunnel OutLabel Outgoing label and the interface of the tunnel Source address of the tunnel Destination address of the tunnel Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 101: Show Mpls Traffic-Eng Tunnels Remote-Tunnel

    Tspec:ave rate= 0 kbits, burst= 2000 bytes, peak rate = 0 kbits RSVP Resv Info: Record Route: NONE Fspec:ave rate= 0 kbits, burst= 2000 bytes, peak rate = 0 kbits The descriptions of the displayed information are shown below. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 102: Tunnel Mpls Oam Back-Up-Lsp Tunnel

    Purpose Tunnel configuration Command Modes tunnel mpls oam tunnelid <tunnel-id> ingress <tunnel-id> Syntax back-forward-lsp < tunnel-index > type {cv | ffd frequence <time>} no tunnel mpls oam tunnelid < tunnel-id > ingress <lsr-id> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 103: Tunnel Mpls Oam Type

    Example 1 and ingress is 1.1.1.1 to cv mode, set reverse tunnel to 2. ZXR10(config)#interface tunnel5 ZXR10(config-if)#tunnel mpls oam tunnelid 1 ingress 1.1.1.1 back-forward-lsp 2 type cv tunnel mpls oam type Use this command to set detection in tunnel mode.

  • Page 104: Tunnel Mpls Traffic-Eng Autoroute Metric

    1. This example describes how to configure the metric value of Example automatic routes as 2. ZXR10(config)#interface tunnel5 ZXR10(config-if)# tunnel mpls traffic-eng autoroute metric 2 ZXR10(config-if)# tunnel mpls traffic-eng autoroute metric absolute 2 ZXR10(config-if)# tunnel mpls traffic-eng autoroute metric relative -2 2.

  • Page 105: Tunnel Mpls Traffic-Eng Bandwidth

    Chapter 5 MPLS Traffic Engineering Configuration ZXR10(config)#interface tunnel5 ZXR10(config-if)# tunnel mpls traffic-eng autoroute metric relative -2 tunnel mpls traffic-eng bandwidth Use this command to configure the bandwidth reserved for estab- Purpose lishing a tunnel on the tunnel interface. Restore default with the no form of this command.

  • Page 106: Tunnel Mpls Traffic-Eng Class-Type

    This example describes how to configure the CT type of the tunnel Example as 1, and the bandwidth requirement as 1000kps. ZXR10(config)#interface tunnel5 ZXR10(config-if)# tunnel mpls traffic-eng class-type 1 bandwidth 1000 tunnel mpls traffic-eng path-option Use this command to configure to obtain ERO by dynamic selection Purpose or explicit path statically on tunnel interface of the device.

  • Page 107: Tunnel Mpls Traffic-Eng Record-Route

    This example describes how to configure the method of obtaining Example ERO is dynamic selection. ZXR10(config)#interface tunnel5 ZXR10(config-if)#tunnel mpls traffic-eng path-option 1 dynamic The following contents will be shown after using this command. ZXR10#show mpls traffic-eng tunnels summary Signalling Summary:...

  • Page 108: Tunnel Mpls Traffic-Eng Tunnels Priority

    This example describes how to configure the setup priority as 2, Example and the holdup priority as 2. ZXR10(config)#interface tunnel5 ZXR10(config-if)#tunnel mpls traffic-eng priority 2 2 tunnel static ingress Use this command to set static tunnel lsp information. Delete the Purpose configuration with the no command.
  • Page 109 This example describes how to set tunnel ingress to 1.1.1.1, Example egress to 2.2.2.2, out-label to 17, out-port to gei_1/1, next-hop to 10.10.10.1. ZXR10(config)#interface tunnel5 ZXR10(config-if)#tunnel static ingress 1.1.1.1 egress 2.2.2.2 out-port gei_1/1 out-label 17 next-hop 10.10.10.1 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 110 ZXR10 Command Manual (MPLS Volume) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 111: Frr Configuration

    Use this command to configure the time interval for the interface Purpose to send RSVP hello requests. Interface configuration Command Modes Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 112: Ip Rsvp Signalling Hello Refresh Misses

    Hello does not falsely declare that a neighbor is down. mpls traffic-eng backup_tunnel Use this command to assign one or more backup tunnels to a pro- Purpose tected interface. Interface configuration Command Modes mpls traffic-eng backup_tunnel <tunnel-id> Syntax Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 113: Show Ip Backup Route

    This command is supported after the platform version 4.6.02 . Instructions This example shows detailed information about a Hello instance. Example ZXR10#show ip rsvp hello instance detail Neighbor 200.1.1.1 Source 200.1.1.2 Hello globally enabled State:UP Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 114: Show Ip Rsvp Hello Instance Summary

    Syntax This command is supported after the platform version 4.6.02. Instructions This example shows summary information about a Hello instance. Example ZXR10#show ip rsvp hello instance summary Clinet I/F Neighbor Type State LostCnt Lsps Et1/1 11.0.0.1...

  • Page 115: Show Mpls Traffic-Eng Fast-Reroute

    FRR intf/label FRR interface: backup tunnel interface Label: the label value advertised by the next hop at the intermediate node Status FRR current state: ready or active Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 116: Show Mpls Traffic-Eng Interface

    Time interval for the interface to send the RSVP hello requests misses Specifies how many Hello acknowledgments a node can miss in a row before the node considers communication with its neighbor is down Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 117: Tunnel Mpls Traffic-Eng Fast-Reroute

    The tunnel supports Fast ReRoute (FRR) and informs the down- stream node that it needs local protection. The downstream node tries its best to offer local protection and sends related information to the head node if local protection is available. Confidential and Proprietary Information of ZTE CORPORATION...

Table of Contents