Literature, Hardware And Tools Parts List - SawStop PCS175 Owner's Manual

Blade Guard and Miter Gauge Parts List
No.
38
39
40

Literature, Hardware and Tools Parts List

No.
1
2
3
4
5
6
7
SawStop
®
10" PROFESSIONAL
CABINET SAW
OWNER'S MANUAL
Model PCS175
1
4
112 SawStop 10" Professional Cabinet Saw
Description
M6x1.0x8 Flat Head Phillips Screw
Retaining Disc
M5x0.8x12 Spring Bearing
Description
PCS175 10" Professional Saw Owner's Manual
Table Saw Hardware Pack
PCS175 Unpacking Procedure Poster
Hex Key Tool Holder (includes M3, M4, M5, M6 hex keys)
M8 Ball End Hex Key
Blade Spacing Adjustment Gauge
Push Stick
Installing the Handwheels Mounting the Dust Port
Hardware for Steps 2-3 Hardware for Step 4
1 Keys, 2 Set Screws, Button Head Screws,
5 x 5 x 25 (2) M6 x 8 (2) 3 M5 x 3 x 15 (3)
Mounting the Extension Wings
Hardware for Step 6
Washers, 7 Lock Washers, M8 (8) 8 Hex Bolts, M8 x 16 (8)
6
M8 (8)
Mounting the Switch Box
Hardware for Step 7
9 Button Head Socket Screws,
M6 x 20 (2)
11 Washers, M6 (2)
Lock Washers,
10 M6 (2)
Blade Spacing
Adjustment Gauge (1)
Hex Key, M8 (1)
Hex Keys: M3 (1), M4 (1), M5 (1), M6 (1)
Tools
F
5
Mounting
the
Lock Washers,
Motor
4 M5 (3)
Cover
Hardware for Step 5
Mounting the
Wrench & Tool
Holders
Hardware for Step 8
Blade
Wrench
Holder
13
14 Lock 15 Button Head
Washers, Screws,
M6 (2) M6 x 12 (2)
Switch Box
Keys (2)
12
Motor
Cover
Rod
5
2
Part No. Qty.
PCS-233
PCS-234
PCS-251
Part No.
PCS-254
PCS-236
PCS-255
PCS-238
PCS-239
PCS-240
PCS-241
How to Stand Up Your Saw
1 2
Your saw is shipped horizontal to protect it from tipping during Take the top piece of Styrofoam and place one of its short sides next to the
transit. To stand up your saw, first remove all packing materials pallet by the back of the saw, as shown in Fig 2a. Place the Styrofoam so that
and accessories from the shipping pallet (see Fig. 1). The other the top edge of the table and the bottom edge of the saw both overhang the
side of this poster shows where all of the accessories are edges of the Styrofoam (see Fig. 2b).
located in the packaging.
Fig. 2a
Fig. 1
3
With the help of another use the table and the
elevation control shaft
person, carefully roll the
as lifting points to help
saw off the pallet and onto
roll the saw
the top piece of Styrofoam,
If you have a Professional
as shown in Fig. 3. You
Cabinet Saw Mobile Base,
can use the cast iron table
install it now while the saw is
and the elevation control
shaft as lifting points to on its side and then continue with
help you roll the saw. Wear step 4. See the manual that comes
safety gloves and be with your Professional Cabinet
careful to use proper lifting Saw Mobile Base for instructions.
technique to avoid injury.
Saw Stop
Fig. 3
3
6
1
1
3
Qty.
1
1
1
1
1
1
1
top piece of
Styrofoam
the bottom edge of
the saw should
overhang the edge
of the Styrofoam
the edge of the table
should overhang the
edge of the Styrofoam
Fig. 2b
4 With the help of another person, carefully tip the saw to the
upright position by lifting under the rear edge of the cast
iron table (see Fig. 4). Lift the saw slowly so that it slides
off the Styrofoam and onto the floor without damaging the
cabinet. Read and understand the owner's manual fully
before assembling and operating your saw.
lift under the rear
edge of the table
Fig. 4
7