Extension Function Mode - Hitachi J300 Series Instruction Manual

(2) Extension function mode

•
•
Display
order
1 Control method setting
2 Motor capacity setting
3 Motor poles setting
4 Speed control response constant setting
5 Start frequency adjustment
6 Maximum frequency limiter setting
7 Minimum frequency limiter setting
8 Jump frequency setting 1
9 Jump frequency setting 2
10 Jump frequency setting 3
11 Carrier frequency setting
12 Frequency command sampling frequency
13 Multispeed first speed setting
14 Multispeed second speed setting
15 Multispeed third speed setting
16 Electronic thermal level adjustment
17 Electronic thermal characteristic selection
18 Motor pole number setting for motor speed monitor
19 External frequency setting start
20 External frequency setting end
21 Instantaneous restart selection
22 Dynamic braking usage ratio
23 Optional arrival frequency for acceleration
24 Optional arrival frequency for deceleration
25 Monitor signal selection
26 Frequency converted value setting
27 Analog input selection
28 Frequency arrival signal output method
29 Restarting after FRS signal selection
30 Reduced voltage soft start setting
31 Running mode selection
32 Jogging freguency setting
33 Base frequency setting
34 Maximum frequency setting
35 Maximum frequency selection
36 Frequency command/output frequency adjust (O-L terminal)
37 Frequency command/output frequency adjust (OI-L terminal)
38 Selection of reset terminal performance
39 P gain setting of PID funciton
40 I gain setting of PID funciton
41 D gain settingof PID function
42 Selection of PID funciton
43 Setting method of PID reference value
44 Setting of PID reference value
45 Auto tuning setitng
46 Motor data selection
47 Ro-To option selection
48 Input terminal setting 1
49 Input terminal setting 2
50 Input terminal setting 3
51 Input terminal setting 4
52 Input terminal setting 5
53 Input terminal setting 6
54 Input terminal setting 7
55 Input terminal setting 8
56 Output terminal setting 11
57 Output terminal setting 12
58 Input terminal a and b contact setting
59 Output terminal a and b contact setting
NOTE 1: The most applicable motor capacity of the inverter is set.
NOTE 2: The initial setting of each inverter is adjusted when shipping from the works.
CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
Each function name and settable range to the extension function mode are shown
below.
Set the extension function code to be changed by
Externsion function name
Screen display
Settable
Code
during Setting range
display
running
A 0 Ñ 0-5
A 1 Ñ 3.7 to 160
A 2 Ñ 2/4/6/8
A 3 Ñ 0.00-9.99/10.0-99.9/100
A 4 Ñ 0.10-9.99
A 5 Ñ 0-120 (400)
A 6 Ñ 0-120 (400)
A 7 Ñ 0-400
A 8 Ñ 0-400
A 9 Ñ 0-400
A10 Ñ 2.0-16.0
A11 Ñ 1-8
A12 Ñ 0-120 (400)
A13 Ñ 0-120 (400)
A14 Ñ 0-120 (400)
A23 Ñ 20-120
A24 Ñ 0-2
A25 Ñ 2 to 48
A26 Ñ 0-120 (400)
A27 Ñ 0-120 (400)
A34 Ñ 0-3
A38 Ñ 0.0-99.9/100
A39 Ñ 0-400
A40 Ñ 0-400
A44 Ñ 0-3
A47 Ñ 0.0-99.9
A48 Ñ 0-1
A49 Ñ 0-2
A54 Ñ 0-1
A58 Ñ 0-6
A59 Ñ 0-2
A61 Ñ 0-9.99
A62 Ñ 30-120 (400)
A63 Ñ 30-120 (400)
A64 Ñ 120/400
A80 Ñ 0-255
A81 Ñ 0-255
A86 Ñ 0, 1
A90 Ñ 0.1-0.5
A91 Ñ 0.0-15.0
A92 Ñ 0.0-100
A94 Ñ 0-4
A95 Ñ 0, 1
A96 Ñ 0.00-200
A97 Ñ 0-2
A98 Ñ 0-2
A99 Ñ 0-1
C 0 Ñ 0-3, 5-9, 11-16, 18-28
C 1 Ñ 0-3, 5-9, 11-16, 18-28
C 2 Ñ 0-3, 5-9, 11-16, 18-28
C 3 Ñ 0-3, 5-9, 11-16, 18-28
C 4 Ñ 0-3, 5-9, 11-16, 18-28
C 5 Ñ 0-3, 5-9, 11-16, 18-28
C 6 Ñ 0-3, 5-9, 11-16, 18-28
C 7 Ñ 0-3, 5-9, 11-16, 18-28
C10 Ñ 0-2
C11 Ñ 0-2
C20 Ñ 00-FF
C21 Ñ 00-07
7-6
.
Settable
for
Remarks
2nd
Initial value
function
√
0
√
NOTE 1
√
4
√
2.00
0.50 Ñ
0 Ñ
0 Ñ
0 Ñ
0 Ñ
0 Ñ
(16.0) Ñ See 7-18
8 Ñ
0 Ñ
0 Ñ
0 Ñ
√
100
√
1
4 Ñ
0 Ñ
0 Ñ
0 Ñ
(1.5) Ñ
See 7-21
0 Ñ
0 Ñ
0 Ñ
1.0 Ñ
1 Ñ
0 Ñ
1 Ñ
6 Ñ
0 Ñ
Frequencies below
1.00 Ñ
the start frequency
cannot be set.
√
60
√
60
120 Ñ
Ñ Ñ NOTE 2
Ñ Ñ NOTE 2
0 Ñ
1.0 Ñ
1.0 Ñ
0.0 Ñ
0 Ñ
0 Ñ
0.00 Ñ
0 Ñ
√
0
0 Ñ
18 Ñ
16 Ñ
5 Ñ
11 Ñ
9 Ñ
13 Ñ
1 Ñ
0 Ñ
0 Ñ
1 Ñ
00 Ñ
04 Ñ
Set
value