Table Of Contents - Hitachi J300 Series Instruction Manual

Table of Contents

Instruction Manual1
Definitions And Symbols2
Hazardous High Voltage2
Precautions3
Revision History Table5
Table Of Contents6
Safety Precautions7
Wiring7
Installation7
Operation8
Input Phase Failure Protection9
Control And Operation10
Maintenance, Inspection And Part Replacement11
Appendix12
Others13
Motor Terminal Surge Voltage Suppression Filter (For The 400 V Class)14
Protection Against Noise Interference From Inverter14
Effects Of Distributor Lines On Inverters15
Inspection Upon Unpacking16
Contents Of Specifications Label16
Description Of Inverter Model16
Appearance And Names Of Parts17
Precaution For Installation And Wiring20
Wiring The Power Supply And Motor23
Wiring Of Control Circuit Terminals25
Sink Type (Factory Settings)25
Source Type Wiring25
Connection To The Programmable Controller27
Wiring Equipment, Options (Emi Filter, Etc.)28
Main Circuit Terminal30
Control Circuit Terminal30
Control Circuit31
Control Circuit Terminals32
Terminal Connection Diagram34
Before Starting Operation35
Test Run37
An Example Of A General Connection Diagram37
Operating With Digital Operator38
Runnign From External Command38
Contact Specification39
Saving The Alarm Signal39
Resetting (Any One Of A, B And C Is Possible)40
Operation Of The Digital Operator41
Names Of Parts41
Key Description42
Explanation Of Screen Display43
Transition Of Each Code44
Digital Operator Initialization List45
Monitor Mode, Function Mode45
Extension Function Mode46
Explanation Of Modes47
Monitor Mode Contents47
Function Mode49
Returning To The Initialization (State Set At Factory Before Shipment)54
How To Delete Trip History Data (D 10 And D 11)54
Extension Function Mode Contents55
A 0 Control Method Setting55
A 1, A 2 Motor Capacity, Motor Poles Setting55
A 3 Speed Control Response Constant Setting56
A 4 Start Frequency Adjustment56
A 5, A 6 Frequency Upper, Lower Limiter57
A 7, A 8, A 9 Jump Frequency Setting 1-357
A 10, Carrier Frequency Setting58
A 11, Frequency Command Sampling Frequency Setting58
A 12, A 13, A 14 Multispeed Setting 1-358
A 23, Electronic Thermal Level Adjustment59
A 24, Electronic Thermal Characteristic Selection59
A 25, Motor Poles Setting For Motor Speed Monitor59
A 26, A 27 External Frequency Setting Start And End60
A 34, Instantaneous Restart Selection (Restart Selection)60
A 38, Dynamic Braking Usage Ratio61
A 39, A 40 Arrival Optional Frequency At Acceleration And At Deceleration61
A 44 Monitor Signal Selection62
A 47 Frequency Converted Value Setting62
A 48 Analog Input Selection62
A 49 Frequency Arrival Signal Output Method63
A 54 Restarting After Frs Signal Selection63
A 58 Reduced Voltage Soft Start Setting64
A 59 Running Mode Selection64
A 61 Jogging Frequency Setting64
A 62, A 63 Base And Maximum Frequency Setting65
A 64 Maximum Frequency Selection65
A 80, A 81 Frequency Command Output Frequency Adjust (O-L, Oi-L)65
A 86 Selection Of Reset Terminal Performance66
A 90, A 91, A 92 Proportional, Integral, Differential Gain Setting66
A 94 Pid Control Selection66
A 95 Target Value Setting Method Selection67
A 96 Internal Target Value Level Setting67
A 97 Auto Tuning Setting67
A 98 Motor Data Selection67
A 99 Ro-T-Option Selection68
C 0 To C 7 Input Terminal Setting 1 To 869
C 10, C 11 Output Terminal Setting 11 And 1270
C 20 Input Terminal A And B Contact Setting71
C 21 Output Terminal A And B Contact Setting71
Protection Functions72
Other Display73
Troubleshooting74
Error Messages And Diagnosis74
How To Reset74
Trouble Shooting79
Maintenance And Inspection Precautions82
Inspection Items82
Daily Inspection And Periodic Inspection84
Measurement Method For I/O Voltage, Current, And Power87
Parts To Be Measured87
Measurement Method For Output Voltage88
Common Standarsd Specifications89
Individual Specification (Usa Version (J300-... Lfu, Hfu))91
Functions When Using The Optional Remote Operator92
Connecting The Remote Operator92
Monitor Mode94
Function Mode List When The Remote Operator Is Used96
Protection Function Display List When The Remote Operator Is Used107
Other Displays107
Warning Error List108
Dimensions109
Remote Operator, Copy Unit109
Copy Unit Function110
Data To Be Copied By The Copy Unit111
Service112
Manual For New Functions113
Autotuning113
Outline Of The Function113
Appendix 1113
Autotuning Start114
Setting Method114
Digital Operator114
Remote Operator114
New Remote Operator115
Display When The Autotuning Terminates116
Display In The Normal State116
Display In The Failure State116
Running Method By Autotuning Data117
Energy Conservation Running120
Fuzzy Most Suitable Acceleration And Deceleration123
Principle124
Instantaneous Power Failure Restart And Commercial Power Source Switching127
Appendix 2127
In The Following Cases, The Equipment May Start At The Lowest Frequency (Called 0 Start)128
Time Chart For Retry Mode128
Commercial Power Source Switching129
Connection Example Diagram And Timing For Commercial Power Source Switching Running130
Capacitor Life Curve131
Appendix 3131
Acceleration/Deceleration Curve Constants132
Appendix 4132
Multi-Motor Operation And Precautions For Operation133
Supplementaly Explanation Of The Function Mode136
Appendix 5136
Appendix 6136
List For Display And Data Read/Copy With Each Operators137
Appendix 7137
Pid Function144
Wiring Sketch144
Pid Gain144
Appendix 8144
Data Setting Method145