Table Of Contents - 3D Printing Systems Up Plus User Manual

1. INTRODUCTION ................................ ..............................................................................................................................
1.1 H
OW TO USE THIS MANUAL
1.2 P ................................................................................................................................ ................................
RECAUTIONS
1.2.1 Safety ................................ ................................................................................................................................
1.2.2 The following classifications are used in this manual.............................................................. 1.2.2 The following classifications are used in this manual.
1.2.3 Protection ................................ ................................................................................................................................
2. OVERVIEW ................................ ................................................................................................................................
2.1 A ................................ ................................................................................................................................
PPEARANCE
2.2 S ................................ ................................................................................................................................
PECIFICATIONS
2.2.1 Printer Physical Characteristics.............................................................................................. 2.2.1 Printer Physical Characteristics
2.2.2 Specifications ................................ ................................................................................................
2.2.3 Environmental specifications ................................................................................................ 2.2.3 Environmental specifications
3. OPERATION ................................ ................................................................................................................................
3.1 P ................................................................................................................................ ................................
REPARATION
3.1.1 Quick Setup ................................ ............................................................................................................................
3.1.2 Installing software ................................
3.1.3 Installing drivers ................................
3.1.4 Updating your ROM
3.1.5 Initialising the Printer ing the Printer ................................................................................................
3.1.6 Setting the Platform Height
3.1.7 Loading the filament into the Extruder Head 3.1.7 Loading the filament into the Extruder Head ................................................................
3.2 U
SING THE BASIC FUNCTIONS
3.2.1 Start the program ................................
3.2.2 Loading a 3D model ................................
3.2.3 View Options ................................ ................................................................................................
3.2.4 Model transformations ................................................................................................ 3.2.4 Model transformations
3.3.4 Other Maintenance Options 3.3.4 Other Maintenance Options ................................................................................................
3.3.5 Preparing the Platform ................................................................................................ 3.3.5 Preparing the Platform
3.3.6 Print Preferences ................................
4. PRINTING ................................ ................................................................................................................................
Options During Printing: ................................
Print Options: ................................ ................................................................................................................................
4.1 E V "
XTRUDER ENT WIND BARRIER WIND BARRIER
4.2 C
ALCULATING MODEL COSTS
5. MODEL REMOVAL ................................ ................................................................................................
5.1 R ................................ ..........................................................................................................................
EMOVING THE RAFT
5.2 R S M
EMOVING UPPORT
6. MAINTENANCE ................................ .............................................................................................................................
6.1 C M
HANGING THE ATERIAL
6.2 V C ................................................................................................ ................................
ERTICAL ALIBRATION
6.3 C
LEANING THE OUTSIDE OF THE NOZZLE
6.4 R / C
EMOVING HANGING THE NOZZLE HANGING THE NOZZLE
6.5 C P
LEANING THE ERFBOARD
6.6 L
UBRICATION OF BEARINGS
6.7 S ................................................................................................................................ ................................
PARE PARTS
UP Plus 3D Printer User Manual 3D Printer User Manual
................................................................................................ ................................
................................................................................................
................................................................................................
................................................................................................
m Height ................................................................................................
................................ ................................................................................................
................................................................................................
................................................................................................
................................................................................................
................................................................................................
" ................................................................................................
................................................................................................ ................................
................................................................................................
ATERIAL IAL
................................ ................................................................................................
................................................................................................
OF THE NOZZLE
................................................................................................
................................ ................................................................................................
................................ ................................................................................................
2. Overview 2. Overview
.............................. 5
.................................................... 5
..................................... 5
....................................... 5
............................. 6
................................ 6
..................................... 7
...................................... 8
................................. 11
.............................. 11
......................................................... 11
................................. 11
.................................. 12
.................................... 12
............................ 12
................................................. 15
.................................................... 16
.............................................. 18
............................................ 19
................................... 20
........................................ 21
............................................... 23
.................................................. 23
............................................... 23
......................................................... 25
......................................... 27
.................................. 29
.......................................... 31
................................................... 32
..................................... 35
................................................. 36
................................. 37
........................................ 38
................................................ 38
........................ 39
.......................... 40
........................................... 40
............................. 42
................................................... 42
....................................................... 42
.................................. 43
..................................... 44
.................................................. 44
.................................................. 44
..................................... 44
v 2013.1.31 .1.31