Applicable Controls - Toshiba Super MMU-AP0092H Service Manual

8

APPLICABLE CONTROLS

REQUIREMENT
• When you use this air conditioner for the first
time, it takes approx. 5 minutes until the remote
controller becomes available after power-on.
This is normal.
<When power is turned on for the first time
after installation>
It takes approx. 5 minutes until the remote
controller becomes available.
Approx. 5 minutes
SETTING SETTING
Power Remote Controller
on flashes goes out is available
<When power is turned on for the second
(or later) time>
It takes approx. 1 minute until the remote
controller becomes available.
Approx. 1 minute
SETTING SETTING
Power Remote Controller
on flashes goes out is available
• Normal settings were made when the indoor
unit was shipped from factory.
Change the indoor unit settings as required.
• Use the wired remote controller to change the
settings.
∗ The settings cannot be changed using the
wireless remote controller, sub remote
controller, or remote-controllerless system
(for central remote controller only).
Therefore, install the wired remote controller
to change the settings.
n Changing of settings of for applicable
controls
Basic procedure for changing settings
Change the settings while the air conditioner is
not working. (Be sure to stop the air conditioner
before making settings.)
The display content for setting differs from that
on the former types of remote controller
(RBCAMT21E/AMT31E).
(The number of CODE NO. has increased.)
4
6
1 5 2
1
Procedure
TEST
Push button and "TEMP . " button simulta-
neously for at least 4 seconds.
After a while, the display flashes as shown in the
figure. Confirm that the CODE No. is [10].
TEST
• If the CODE No. is not [10], push button to
erase the display content, and repeat the proce-
dure from the beginning.
(No operation of the remote controller is accepted
TEST
for a while after button is pushed.)
(While air conditioners are operated under the
group control, " " is displayed first.
UNIT LOUVER
When is pushed, the indoor unit number
displayed following " " is the header unit.)
(∗ Display content varies with the indoor unit model.)
2
Procedure
UNIT LOUVER
Each time you push button, indoor unit
numbers in the control group change cyclically.
Select the indoor unit you want to change settings
for. The fan of the selected unit runs and the louvers
start swinging. You can confirm the indoor unit for
which you want to change settings.
3
1
Procedure
3
Using "TEMP . / " buttons, specify CODE No.
[ ].
4
Procedure
Using timer "TIME / " buttons, select SET
DATA [ ].
5
Procedure
SET
Push button. When the display changes from
flashing to lit, the setup is completed.
• To change settings of another indoor unit, repeat
2
from Procedure .
• To change other settings of the selected indoor
unit, repeat from Procedure
SET
Use button to clear the settings.
SET
To make settings after button was pushed,
2
repeat from Procedure .
6
Procedure
When settings have been completed, push
button to determine the settings.
TEST
When button is pushed,
SETTING
the display content disappears and the air condi-
tioner enters the normal stop mode.
(While is flashing, no operation of the remote
SETTING
controller is accepted.)
n When installing separately sold filters
Be sure to make ceiling setting when installing
separately sold filters.
∗ Separately sold filters cannot be installed in an
indoor unit on a high ceiling.
Follow to the basic operation procedure
→ → →
1 2 3
(
• For the CODE No. in Procedure
[5d].
• For the set data in Procedure
SET DATA of filters to be installed from the
following table.
SET DATA
0000
SET DATA
0003
n Installing indoor unit on high ceiling
When an indoor unit is installed on a ceiling
higher than the standard height, make the
high-ceiling setting for air volume adjustment.
• Take the same procedure as that in "When
installing separately sold filters".
• For the set data in Procedure
3
• Select the SET DATA for Procedure
.
the "Height list of ceiling possible to be
installed" table on page 35 in this manual.
TEST
flashes and then
→ →
4 5 6
).
3
, specify
4
, select the
High-ceiling setting
Normal filter (Factory setting)
High-ceiling setting
High Efficiency Filter (65%)
High Efficiency Filter (90%)
3
, specify [5d].
4
from