Modifying Th Pitch (Morph Bend Assign Switch) - Roland JP-8080 Owner's Manual

3
Create the sound that will be heard when the maxi-
mum value (127) of aftertouch is received.
These operations will determine the width over which
the parameters will change.
Moving a slider/knob for which the width of change
has already been set will overwrite and modify the pre-
viously made settings.
By operating the controller of the external MIDI device,
you can audition the current settings (the change in
sound). Conversely, when the [CONTROL ASSIGN]
indicator is blinking, the sound will not change even if
you move the sliders/knobs, unless the controller of the
external MIDI device is operated.
4
Press [CONTROL ASSIGN] or [EXIT].
The indicator will change to lit, and the previous display
will reappear.
This completes control assign settings.
If control assign settings have been made, the [CONTROL
ASSIGN] indicator will always be lit. Conversely, if the
[CONTROL ASSIGN] indicator is dark, no parameter
changes have been assigned, and the sound will not change
even if you operate the controller of the external MIDI
device.
5
Return the sliders/knobs to the positions in which
they were set for step 1.
When you operate the controller of the external MIDI
device, the values of each parameter will change in the
amount specified in step 3, centered at the current positions
of the sliders/knobs.
This means that if you move the sliders/knobs after making
settings, the parameter values which correspond to an after-
touch/breath value of zero will change. The width of
change will not change.
(a)
(b)
(c)
moved while keeping the same range of change
(a)
Value when the maximum aftertouch value (127) is received
(b) Value when the minimum aftertouch/breath value (0) is received
(alternatively, the value when aftertouch or breath are not received)
(c)
Value when the maximum breath value (127) is received
* When you wish to check the width of the parameter
change, press [CONTROL ASSIGN] while appearing the
Temporary Scope display, and then move the
sliders/knobs (Control Scope: p.63).
* If you wish to view the width of parameter change in
the display as you make settings, press [CONTROL
ASSIGN] when the Edit Scope page is displayed, and
move the sliders/knobs (Control Edit Scope: p.64).
* If the Control Assign is used simultaneously with
Velocity (p.81) or Motion Control (p.98), any overlap-
ping parameters will have their values added to pro-
duce the resulting change.
* Vocal Morph Control (p.104) parameters can also be
controlled by aftertouch or breath. Thus, if these are
controlled simultaneously, the last-arriving control mes-
sage will change the parameter value.
Modifying the Pitch
(Morph Bend Assign Switch)
If you turn on the Morph Bend Assign Switch, the pitch will
change simultaneously with the other parameters.
When Aftertouch messages are received, the pitch will
change according to the value specified for Bend Range Up
(p.89). When Breath messages are received, the pitch will
change according to the value specified for Bend Range
Down (p.89).
However, this is only for reception from REMOTE KBD IN.
In the case of reception from MIDI IN, there will no change.
You can change this so that MIDI messages other than
Aftertouch or Breath can be used for control (p.86).
This parameter can be set independently for each patch.
1
Press [EDIT].
The [EDIT] indicator will light, and the BANK[1]–[8]
indicators will blink.
2
Press [PATCH] (BANK [4]) several times to select
the Morph Bend Assign Switch page.
The [PATCH] indicator will light.
(a)
3
Press PANEL SELECT [LOWER]/[UPPER] to select
(b)
the part whose settings you wish to change.
If you press [LOWER]/[UPPER] simultaneously, both
(c)
indicators will light and you can simultaneously modify
the settings of both parts.
In this case, the panel will indicate the settings of the
Upper patch.
4
Press [DEC]/[INC] to turn this ON.
5
When you have finished making settings, press
[EDIT] or [EXIT].
You will return to the previous display.
The Morph Bend Assign Switch setting has now been
made.
85