Making Vocal Morph Control Settings; Controlling Voice Modulator Parameters In Realtime; Use Panel Select To Select The Voice Modulator Panel; Types Of Voice Modulator Parameters - Roland JP-8080 Owner's Manual

3–8 MEASURES:
The ensemble rate will be synchronized to the tempo of the
internal sequencer, and ensemble will be applied at the
interval of the specified note or measure.
* If the MIDI Sync (p.123) setting is set to MIDI IN or
REMOTE KBD IN, the ensemble rate will synchronize to
the external MIDI clock (p.144).
Making Vocal Morph Control
Settings
Vocal Morph Ctrl
(Vocal Morph Control Switch)
This is the on/off switch for vocal morph control. Turn this
on when you wish to use vocal morph control.
Vocal Morph Sens
(Vocal Morph Sensitivity)
This specifies how deeply vocal morph control will be
affected by your voice. With a setting of 0, there will be no
effect. With a setting of +63, the control will change from 0
to the maximum positive value in response to even a slight
input sound. With a setting of -64, the control will change
from 0 to the maximum negative value in response to even
a slight input sound. Normally you should use this with a
setting in the range of +32 to -32.
When Vocal Morph Sens is set to a positive value (+), the
characteristics of the input voice will be converted into the
MIDI messages specified for Control Up (p.86). When Vocal
Morph Sense is set to a negative value (-), the characteristics
of the input voice will be converted into the MIDI messages
specified for Control Down (p.86).
Vocal Morph Thrsh
(Vocal Morph Threshold)
This sets the minimum input level for the voice. The para-
meter will be controlled by sound that is greater than the
level specified here.
Example of Vocal Morph Control
Select the performance P2:81 VOCAL MORPH FBK, and
input an "a" sound from the mic. The Upper patch will be
modified by your voice. At the same time, a formant filter
effect will be produced in the Lower patch.
* Refer to page 163 for an example of creating a sound
which uses Vocal Morph Control.
Controlling Voice Modulator
Parameters in Realtime
Use Panel Select to Select The
Voice Modulator Panel
You can use sliders/knobs to modify the Voice Modulator
parameters in realtime. In order to do this, the panel must
be switched to the Voice Modulator Panel.
OFF, ON
1 Hold down [SHIFT] and press PANEL SELECT
[UPPER].
PANEL SELECT [LOWER] and [UPPER] will both blink,
and the Voice Modulator panel will be in effect. The
Voice Modulator [ON] will always be on. In this condi-
-64–+63 tion, you can operate the front panel sliders/knobs
labeled in blue characters to modify Voice Modulator
parameters. (Refer to the following item.)
* While the Voice Modulator panel is selected, it is not
possible to modify patch parameters (except for [VOICE
MOD SEND] in the EFFECTS section) from the front
panel.
2 To return to the previous state, hold down [SHIFT]
once again and press PANEL SELECT [UPPER], or
press [EXIT].
* If, while the Voice Modulator Panel is selected, you use
Edit mode (p.108) to set [PART] and [PATCH], the
PANEL SELECT [LOWER] and [UPPER] will blink only
for the button of the part which you are setting.
Types of
Voice Modulator Parameters
0–127
The following Voice Modulator parameters can be edited in
realtime from the Voice Modulator panel. When you move
a slider/knob, the display will indicate the parameter name.
These parameters can be set independently for each perfor-
mance.
* Parameters marked by an asterisk (*) are ignored when
the algorithm is set to "FLT BANK WIDE" or "FLT
BANK NARROW." If the corresponding slider/knob is
moved, the display will indicate an "x" to indicate that
these parameters are invalid.
111