HP 6125G Configuration Manual page 173
Layer 2 - lan switching
Hide thumbs
Also See for 6125G:
- Command reference manual (426 pages) ,
- Configuration manual (379 pages) ,
- Release note (60 pages)
Table of Contents
Advertisement
[PE1-GigabitEthernet1/0/1] port trunk permit vlan 100
# Configure VLAN 100 as the PVID for the port.
[PE1-GigabitEthernet1/0/1] port trunk pvid vlan 100
# Enable basic QinQ on the port.
[PE1-GigabitEthernet1/0/1] qinq enable
[PE1-GigabitEthernet1/0/1] quit
Configure GigabitEthernet 1/0/2:
# Configure GigabitEthernet 1/0/2 as a trunk port and assign it to VLAN 100 and VLAN 200.
[PE1] interface gigabitethernet 1/0/2
[PE1-GigabitEthernet1/0/2] port link-type trunk
[PE1-GigabitEthernet1/0/2] port trunk permit vlan 100 200
# Set the TPID value in the outer VLAN tag to 0x8200 on the port.
[PE1-GigabitEthernet1/0/2] qinq ethernet-type service-tag 8200
[PE1-GigabitEthernet1/0/2] quit
Configure GigabitEthernet 1/0/3:
# Configure GigabitEthernet 1/0/3 as a trunk port and assign it to VLAN 200.
[PE1] interface gigabitethernet 1/0/3
[PE1-GigabitEthernet1/0/3] port link-type trunk
[PE1-GigabitEthernet1/0/3] port trunk permit vlan 200
# Configure VLAN 200 as the PVID for the port.
[PE1-GigabitEthernet1/0/3] port trunk pvid vlan 200
# Enable basic QinQ on the port.
[PE1-GigabitEthernet1/0/3] qinq enable
[PE1-GigabitEthernet1/0/3] quit
Configure PE 2:
2.
Configure GigabitEthernet 1/0/1:
# Configure GigabitEthernet 1/0/1 as a trunk port and assign it to VLAN 200.
<PE2> system-view
[PE2] interface gigabitethernet 1/0/1
[PE2-GigabitEthernet1/0/1] port link-type trunk
[PE2-GigabitEthernet1/0/1] port trunk permit vlan 200
# Configure VLAN 200 as the PVID for the port.
[PE2-GigabitEthernet1/0/1] port trunk pvid vlan 200
# Enable basic QinQ on the port.
[PE2-GigabitEthernet1/0/1] qinq enable
[PE2-GigabitEthernet1/0/1] quit
Configure GigabitEthernet 1/0/2:
# Configure GigabitEthernet 1/0/2 as a trunk port and assign it to VLAN 100 and VLAN 200.
[PE2] interface gigabitethernet 1/0/2
[PE2-GigabitEthernet1/0/2] port link-type trunk
[PE2-GigabitEthernet1/0/2] port trunk permit vlan 100 200
# Set the TPID value in the outer VLAN tag to 0x8200 on the port.
[PE2-GigabitEthernet1/0/2] qinq ethernet-type service-tag 8200
[PE2-GigabitEthernet1/0/2] quit
164
Advertisement
Table of Contents
