Respironics BiPAP autoSV Advanced User Manual page 43

A
G M
UIDANCE AND ANUFACTURER
electromagnetic environment specifi ed below. Th e user of this device should make sure it is used in such an environment.
E T
MISSIONS EST
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fl uctuations/Flicker emissions
IEC 61000-3-3
G M
UIDANCE AND ANUFACTURER
electromagnetic environment specifi ed below. Th e user of this device should make sure it is used in such an environment.
I T
MMUNITY EST
Electrostatic Discharge (ESD) ±6 kV contact
IEC 61000-4-2 ±8 kV air
Electrical Fast Transient/Burst ±2 kV for power supply lines
IEC 61000-4-4 ±1 kV for input-output lines
Surge ±1 kV diff erential mode
IEC 61000-4-5 ±2 kV common mode
Voltage dips, short <5% U
interruptions and voltage (>95% dip in U
variations on power supply 40% U
input lines (60% dip in U
IEC 61000-4-11 70% U
(30% dip in U
<5% U
(>95% dip in U
Power frequency (50/60 Hz) 3 A/m
magnetic fi eld
IEC 61000-4-8
NOTE: U is the a.c. mains voltage prior to application of the test level.
T
A: EMC I
PPENDIX
' D - E
S ECLARATION LECTROMAGNETIC
C
OMPLIANCE
Group 1
Class B
Class A
Complies
' D - E
S ECLARATION LECTROMAGNETIC
IEC 60601 T C
EST OMPLIANCE
L
EVEL
±6 kV contact
±8 kV air
±2 kV for supply mains
±1 kV for input/output lines
±1 kV diff erential mode
±2 kV for common mode
<5% U
T T
) for 0.5 cycle (>95% dip in U
T
40% U
T T
) for 5 cycles (60% dip in U
T
70% U
T T
) for 25 cycles (30% dip in U
T
<5% U
T T
) for 5 sec (>95% dip in U
T
3 A/m
User Manual
NFORMATION
E :
Th is device is intended for use in the
MISSIONS
E E
LECTROMAGNETIC NVIRONMENT
The device uses RF energy only for its internal function. Therefore, its
RF emissions are very low and are not likely to cause any interference
in nearby electronic equipment.
The device is suitable for use in all establishments, including
domestic establishments and those directly connected to the public
low-voltage power supply network.
I :
Th is device is intended for use in the
MMUNITY
L E
EVEL LECTROMAGNETIC
Floors should be wood, concrete or ceramic
tile. If fl oors are covered with synthetic
material, the relative humidity should be at
least 30%.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
typical home or hospital environment.
Mains power quality should be that of a
) for 0.5 cycle typical home or hospital environment. If
T
the user of the device requires continued
) for 5 cycles operation during power mains interruptions,
T
it is recommended that the device be
) for 25 cycles powered from an uninterruptible power
T
supply or a battery.
) for 5 sec
T
Power frequency magnetic fi elds should be
at levels characteristic of a typical location in
a typical hospital or home environment.
39
- G
UIDANCE
E -
NVIRONMENT
G
UIDANCE