Table of Contents
Advertisement
SIMPLICITY INSTALLATION MANUAL.
13. DISABLEMENT
On the Simplicity, there are 2 disablement options. A whole zone of detectors can be disabled, or an individual
point can be disabled. Both types of disablement can be used at the same time if required.
13.1 ZONE DISABLEMENT
To aid commissioning and assist routine maintenance checks, any of the zones or the loop sounders can be
disabled.
When a zone is disabled, the panel will not respond to any fault or fire signals it receives from DETECTORS
from that zone. Call points will remain operational.
This might be used if the system requires routine maintenance, and the customer needs the system to continue
running, but doesn't want spurious false alarms.
The panel will respond in the usual manner to any events in any non-disabled zones.
The Simplicity also allows the loop sounders to be disabled. If they are disabled, the panel will not start
any sounders in an alarm condition.
13.2 TO PROGRAMME ZONE (OR SOUNDERS) AS DISABLED
Any number of zones (or the sounders) can be disabled, but it is good practice to only disable one zone at a
time.
1.
Insert and turn control key to enabled position;
2.
Press GENERAL DISABLEMENT button and the screen will
show: ZONE DISABLEMENT ZONE 1. The panel is now in
SELECT DISABLEMENT MODE.
3.
Press DISABLEMENT SELECT until the required zone or
loop sounders is DISPLAYED. Press DISABLEMENT
CONFIRM button. The screen will now show that the zone is
disabled, and the Zone or Sounder LED will
come on steady, along with the GENERAL DISABLEMENT LED.
This section is now disabled. (NOTE: Call points in this zone
will still be active. To disable the call points as well, disable them individually as points – see 13.3)
4.
If more than one zone (or sounder) needs to be disabled, then press DISABLEMENT SELECT again until
the required zone (or sounder) is selected.
5.
If the panel needs to be taken out of SELECT DISABLEMENT MODE (eg to silence a fault on another
part of the system), Either press GENERAL DISABLEMENT button, or turn the keyswitch off, then back
on again.
6.
Once all the maintenance work has been done the zones need to be enabled again. If the panel is still in
SELECT DISABLEMENT MODE, jump to paragraph 7, otherwise, turn the keyswitch to controls enabled,
press GENERAL DISABLEMENT button. The panel is now in SELECT DISABLEMENT MODE
7.
Press the DISABLEMENT SELECT button until the disabled zone is displayed on the screen. Press
DISABLEMENT CONFIRM button to de-select disablement. Scroll to any other disabled zone and enable
in the same way. When all zones are enabled again, the GENERAL DISABLEMENT LED will turn off.
Turn the keyswitch to off position to return the system to normal. (NOTE: This will also enable any points
individually disabled in that zone)
13.3 POINT DISABLEMENT
The Simplicity Plus panel can also disable individual devices (detector,
call point, sounder or interface). To do this, enter CONFIGURATION
MENU 2 and select EDIT DEVICE. Select the required device, them
press GENERAL DISABLEMENT button. The Device label now flashes
between the programmed label and Device Disabled. The general
disablement LED will also be lit. This device is now disabled.
To re-enable the device, press the disable button again. Note that the Zone disablement LED for this address
will not light because this would suggest that the whole zone is disabled, so would be misleading.
Approved Document No: GLT.MAN-107
Issue : 2.00
Authorised: GH
Date: 4/06/2007
Software:PANEL:R1107 & LOOP:R1062
Zone Disablement
Zone
1
Enabled
Single Devices:
Zone Disablement
Zone
3
Disabled
Single Devices:
Optical
Analog:
25
Normal
Device Disabled
Zone:01
Lp:1 Ad:016
0
0
PAGE 22
Advertisement
Table of Contents
