Connecting To The Vehicle's 12 V Dc Power Supply; Connecting An Amplifier - Silvercrest KH 2391 Operation Manual

Installation
Connecting to the vehicle's
L
12 V DC power supply
c Warning!
· Before connecting to the 12 V DC power supply of
a motor vehicle, consult the vehicle's operation
manual on how to maintain electrical safety!
· Ensure that when you establish the connection
to the 12 V DC power supply the connection
leads of the vehicle are not carrying any voltage.
Do not damage any safety equipment such as
the on-board computer or the alarm system of
the vehicle.
· Establish the connection to the 12 V DC power
supply with 3 x 1 A fuse holders!
· When installing in a motor vehicle you should
ensure that the vehicle cannot be operated and
is completely immobilised! Turn off the ignition
and park the vehicle with the handbrake applied!
· During installation you should use tools with a
double insulated handle!
· Avoid electrical short circuits when connecting
to the 12 V DC power supply.
· When establishing the connection between the
car radio and the 12 V DC power supply make
sure it is completely protected against moisture!
Tip! Use an ISO Plug.
• Please ensure that the intact 10 A flat blade
fuse f l is inserted into the flat the blade fuse
socket eu as far as it will go.
• Guide the connection cables for the 12 V DC
power supply carefully out of the front of the
DIN assembly bracket
• Establish the connection between the connection
cables of the ISO plug and the connection cables
of the 12 V DC power supply with the 3 x 1 A
fuse holders. Ensure that the connections of
the 3 x 1 A fuse holders do not cause any short
circuit and that the fixing screws are firmly
tightened.
• Using a 1 A fuse holder, connect the cable for
the 12 V DC constant current plug-in
connection cable for the 12 V DC constant current
of the motor vehicle.
• Optional - only if an electric aerial is connected:
12 GB/IE
KH2391_Content_UK.indd 12
iq .
fn
to the
Using one 1 A fuse holder each, connect the
cables for the 12 V DC ignition current
electric aerial fo plug-ins to the connection
cable for 12 V DC ignition current of the vehicle.
In this manner the car radio and an electric aerial
can only use current from the vehicle when the
ignition is switched on.
• Using a biscuit connector, connect the cable for
the minus / earth connection plug-in in the
vehicle fq to the minus pole connection cable of
the vehicle (minus pole of the battery, which is
connected to the bodywork of the motor vehicle
as standard).

Connecting an amplifier

L
Tip! Use two cinch connection cables (insulation
and plug: white / red).
You can connect an amplifier to the device for
each loudspeaker channel (LINE OUT).
• Install the two cinch connection cables in the
vehicle according to their operating instructions.
• Pass two cinch connection cables to the amplifier
and carefully out of the front of the DIN assembly
bracket iq .
• Insert the red plug of the first cinch connection
cable as far as it will go into the OUT / REAR
cinch R plug jack (amplifier connection
[red / rear right]) fs .
• Then insert the two red plugs of the first cinch
connection cable as far as it will go into the
REAR cinch R plug jack (amplifier connection
[red / rear right]) of the amplifier.
• Insert the white plug of the first cinch connection
cable as far as it will go into the OUT / REAR
cinch L plug jack (amplifier connection
gl
[white / rear left]) .
• Then insert the second white plug of the first
cinch connection cable as far as it will go into
the REAR cinch L plug jack (amplifier connection
[white / rear left]) of the amplifier.
• Insert the red plug of the second cinch
connection cable as far as it will go into the
OUT / FRONT cinch plug jack (amplifier
connection [red / front right])
fp and
go
.
05.09.2006 14:49:12 Uhr