Connection With Car's 12 V Dc Power Supply; Connection With Cd Changer - Silvercrest KH 2389 Operating Instructions Manual

Assembly
· Hook up the connecting lead of the plug in
with the (+) lead for the rear right loudspeaker.
· Hook up the connecting lead of the plug in
with the (-) lead for the rear right loudspeaker.
· Hook up the connecting lead of the plug in
with the (+) lead for the front right loudspeaker.
· Hook up the connecting lead of the plug in
with the (-) lead for the front right loudspeaker.
· Hook up the connecting lead of the plug in
with the (+) lead for the front left loudspeaker.
· Hook up the connecting lead of the plug in
with the (-) lead for the front left loudspeaker.
· Hook up the connecting lead of the plug in
with the (+) lead for the rear left loudspeaker.
· Hook up the connecting lead of the plug in
with the (-) lead for the rear left loudspeaker.
í
Connection with car's 12 V DC
power supply
Danger!
· Before hooking up to the car's 12 V DC power
supply consult the vehicle's operation manual
on how to observe electrical safety!
· Ensure that when connecting the 12 V DC power
supply there is no voltage on the vehicle's con-
necting cords. Do not damage any safety facilities,
e.g. board computer and alarm system of vehicle.
· Connect the 12 V DC power supply with the 3 x
8 A fuse holders!
· During vehicle installation ensure that the vehicle
is out of operation and is in safe standstill! Turn
off the ignition and bring the vehicle into parking
position with activated hand-brake!
· During connection, use tools with double-insu-
lated handle!
· Avoid electrical short circuits when connecting
to the 12 V DC power supply.
· Connect the MP3 car radio - recorder with the
12 V DC power supply while fully protected
against humidity!
Tip! Use an ISO plug.
· Ensure that the fault-free fl at blade fuse 7.5 A
eu is inserted all the way to the catch of the fl at
blade fuse socket et
12 GB
KH2389_Radio_content_UK.indd 12 KH2389_Radio_content_UK.indd 12
el
em
en
eo
ep
eq
er
es
.
· Carefully guide the connecting cable to hook up
the 12 V DC power supply through the front out
of the DIN assembly bracket.
· Connect the ISO plug with the connecting cables
of the 12 V DC power supply with the 3 x 8 A fuse
holders. Ensure that the connections of the
3 x 8 A fuse holders do not cause any short cir-
cuits and that the fi xing screws are fi rmly
tightened.
· Connect the cable for the 12 V DC constant cur-
fm
rent plug-in using a 8 A safety holder with
the vehicle's connecting cable for the 12 V DC
constant current.
· Connect the cables for the 12 V DC ignition cur-
rent plug-in fo and powered aerial plug-in
with the help of one 8 A safety fuse each with
the vehicle's connecting cable for 12 V DC ignition
current. With this step the MP3 car radio - recorder
and a powered aerial can only consume the
vehicle's power when the ignition is switched on.
· Connect the cable for the vehicle's minus / ground
fp
connection plug-in with the help of a biscuit
connector with the car's connection cable for
the minus pole (battery's minus pole which by
standard is connected with the car's chassis).
· Connect the cable for the powered aerial plug
in fn with the connection for the vehicle's 12 V DC
ignition power (current only active when ignition
is switched on).
· Connect the cable for the vehicle's minus/
ground connection plug-in
a biscuit connector with the car's connection
cable for the minus pole (battery's minus pole
which by standard is connected with the car's
chassis).
í

Connection with CD Changer

Tip! Use a connecting cable with DIN 8-pole plug.
· Install the connecting cable with the DIN 8-pole
plug in accordance with its operation manual
in the car.
· Guide the connecting cable with the DIN 8-pole
plug to the CD changer and carefully out of the
front of the DIN assembly bracket.
fn
fp
with the help of
08.09.2005 11:39:03 Uhr 08.09.2005 11:39:03 Uhr