Playback Operations Using Thumbnails - Sony PDW-F1600 Operation Manual

Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is ±20 times normal speed or maximum
speed (as selected by an extended menu setting).
1) Maximum speed is about ±50 times normal speed. However, the
maximum speed may vary depending on the state of the clip and the
playback position on the disc.
To carry out playback in shuttle mode, proceed as follows.
ACCESS
CH-1 CH-3
ALL CH
CH-2 CH-4
CHAPTER
EXPAND
VARIABLE KEY INHI
REC PAGE
NET
ON
PRE-
LOCAL
SET
OFF
REMOTE HOME
PB
PHONES LEVEL PREV PLAY
DISPLAY
SHIFT
TOP F REV
1
Press the SHTL/JOG button, turning it on.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in shuttle mode starts.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to "dial" (factory
default setting), you can start shuttle playback by
simply rotating the shuttle dial, even when the SHTL/
JOG button is not lit.
To alternate between normal-speed playback and
shuttle mode playback
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SHTL/JOG buttons alternately.
Playback in variable-speed mode
In variable-speed mode, you can control the speed of
playback in the range of –2 to +2 times normal speed. (You
can use setup menu item 119 VARIABLE SPEED LIMIT
IN KEY to specify the speed range of variable playback.)
To carry out playback in variable-speed mode, proceed as
follows.
66
Playback
1)
EJECT
PUSH SET(S.SEL) MARK1
IN OUT
MENU
MARK2
SHTL/JOG
VAR/JOG
RESET
RETURN
NEXT STOP REC
THUMBNAIL
SUB CLIP
DISC MENU
F FWD END STANDBY REC INHI
3 1 2,3
ACCESS
CH-1 CH-3
ALL CH
CH-2 CH-4
CHAPTER
EXPAND
VARIABLE KEY INHI
REC PAGE
NET
ON
PRE-
LOCAL
SET
REMOTE OFF
PB HOME
PREV PLAY NEXT STOP
PHONES LEVEL
DISPLAY
SHIFT
TOP F REV F FWD END STANDBY
3
1
Press the VAR/JOG button, turning it on.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in variable-speed mode starts.
3
To stop playback in variable-speed mode, return the
shuttle dial to the center position, or press the STOP
button.
To alternate between normal-speed playback and
variable-speed mode playback
Set the shuttle dial to the position corresponding to the
desired variable playback speed, then switch between
normal-speed playback and variable-speed mode playback
by pressing the PLAY and VAR/JOG buttons alternately.
To repeat playback in variable mode
Set setup menu item 142 REPEAT MODE to "play &
VAR fwd" or "force".
This allows you to perform repeat playback, limited to
variable playback in the forward direction in the range 0 to
±2 times normal speed.
To perform manual frame sync playback
During playback, you can adjust the playback output phase
in units of one frame. To do so, hold down the PLAY
button and turn the PUSH SET(S.SEL) knob in either
direction.
To speed up the phase: Turn clockwise.
To delay the phase: Turn counterclockwise.
Playback operations using
thumbnails
Playback operations that you can perform with thumbnails
include searching for clips, displaying clip information,
playing clip lists created with the scene selection function,
and locking and deleting clip. This allows you to check the
actual video as you work.
EJECT
PUSH SET(S.SEL) MARK1
IN OUT
MENU
MARK2
SHTL/JOG
VAR/JOG
RESET
RETURN
REC
THUMBNAIL
SUB CLIP
DISC MENU
REC INHI
2,3 1