Play Button; Next Button - Sony PDW-F1600 Operation Manual

5 Recording and playback control section
1 PREV button
PREV PLAY
TOP F REV
6 STANDBY indicator
7 REC INHI indicator
a PREV (previous) button
Press this button, turning it on, to show the first frame of
the current clip. While the first frame of a clip is shown,
pressing this button jumps to the beginning of the previous
1)
clip. This button is also used together with other buttons
for the following operations.
Reverse direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the reverse direction is carried out.
Displaying the first frame of the first clip: Hold down
the SHIFT button, and press this button.
1) When setup menu item 153 FIND MODE is set to "clip & rec start mark",
this button jumps to the frame where the previous Rec Start essence mark
is set and displays the video of that frame.
b PLAY button
To start playback, press this button, turning it on.
When pressed during recording, stops recording and enters
stop mode. If you do not want to stop recording when this
button is pressed, set setup menu item 145 MODE KEY
ENABLE DURING RECORDING to "stop".
c NEXT button
Press this button, turning it on, to jump to the next clip, and
1)
show the first frame.
with other buttons for the following operations.
Forward direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the forward direction is carried out.
Displaying the last frame of the last clip: Hold down the
SHIFT button, and press this button.
1) When setup menu item 153 FIND MODE is set to "clip & rec start mark",
this button jumps to the frame where the next Rec Start essence mark is set
and displays the video of that frame.
d STOP button
To stop recording or playback, press this button, turning it
on. The frame at the stop point appears.
The unit enters standby off mode when you press this
button with the SHIFT button held down. It returns from
standby off mode to the original state when you press this
22
Front Panel

2 PLAY button

3 NEXT button

4 STOP button
5 REC button
NEXT STOP REC
F FWD END STANDBY REC INHI
This button is also used together
button again with the SHIFT button held down. (The lit or
unlit status of the STOP button does not change.)
Note
This button flashes when setup menu item 105
REFERENCE SYSTEM ALARM is set to "on" and the
correct reference video input signal (as specified by OUT
REF on page P6 REF of the function menu) is not being
input.
This unit can automatically enter standby off mode
whenever a specified time elapses in disc stop mode. For
details, see the description of setup menu item 501 STILL
TIMER (page 135).
e REC (record) button
To start recording, hold down this button, and press the
PLAY button. The recording takes place on an unrecorded
part of the disc.
To stop recording, press the STOP button.
To monitor in E-E mode
You can press this button from stop mode to monitor input
signals in E-E mode. The button lights when pressed. Press
the STOP button to return to the original video.
You can also press this button during playback and
searches. E-E mode playback continues for as long as the
button is held down.
To use the REC button as a remaining disc capacity
alarm
Make the following settings.
• Function menu page P7 OTHER >REC REMAIN
ALARM: enable
• Setup menu item 150 REC MODE: disc exchange cache
When the remaining disc capacity drops below two
minutes, the button begins to flash, to prompt you to
exchange the disc.
f STANDBY indicator
Lights when the unit is in standby mode (STOP button and,
STANDBY indicator lit).
After a certain time passes in a disc stop mode, the unit
automatically enters standby off mode and the indicator
goes off.
You can specify the time until the unit enters standby off
mode. For details, see the description of setup menu item
501 STILL TIMER (page 135).
g REC INHI (recording inhibit) indicator
This lights in the following cases.
• When a disc with recording inhibited is loaded.
• When REC INH on the HOME page of the function
menu is set to "ON".