Sony PDW-F1600 Operation Manual page 142

Item number Item name
807 AUDIO OUTPUT PHASE
808 INTERNAL AUDIO SIGNAL
GENERATOR
815 AUDIO SAMPLING RATE
CONVERTER
819
AUDIO INPUT ARRANGE
823 NON-AUDIO FLAG PB
Sub-item
1 CH1/CH2
2 CH3/CH4
3 CH5/CH6
4 CH7/CH8
824 ANALOG LINE OUTPUT SELECT
827 AES/EBU AUDIO OUTPUT SELECT Select the audio signals to assign to AES/EBU audio output channels.
Sub-item
1 CH1/CH2
2 CH3/CH4
828 SDI AUDIO OUTPUT SELECT
Sub-item
1 CH1/CH2
2 CH3/CH4
831
TS OUT AUDIO MODE
142
Setup Menu
Menu items in the 800s, relating to audio control
Settings
Set the output timing of digital audio playback signals (HDSDI, SDI, AES/
EBU only), with 80H as a reference position. Output timing is earlier for
values smaller than 80H and later for values greater than 80H. (80H, 128
samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs)
0 (0 (HEX))... 80 (80 (HEX))... FF (FF (HEX)): Values can be set in this
range.
Select the operation of the internal audio test signal generator.
silnc (silence): Silent signal.
1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.
When you set the A1 INPUT item on page P2 AUDIO of the function
menu to "SG", the internal signal generator operates and outputs
simultaneous test signals to channels 1 to 8 (see page 49).
Select the mode of operation of the sampling rate converter for AES/
EBU input to channels 1 to 4.
off: Do not operate.
on: Operate.
a) Set up mixing of audio signals.
For details, see "To set up mixing of audio input signals" (page 62).
Control non-audio flags in digital audio output.
During playback (except E-E mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto: Set as follows.
• When data is read from disc and confirmed: Follow the data.
• When data from disc is not confirmed: Maintain current state.
Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
Select the audio signals to assign to SDI audio output channels.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
b) Select the number of output channels for i.LINK TS (HDV) signals.
4ch: 4 channels
2ch: 2 channels