Table of Contents
Advertisement
Setup menus
USER menu
<OPERATION>
No.
112
113
The accidental erasure
prevention
function
prevents sections of the
tape on which material
has
already
been
114
recorded
from
being
recorded over.
Heads for CTL recording
signals
and
playback
signals are positioned as
shown
in
the
figure
below.
These
heads
permit or inhibit recording
based on whether or not
CTL signals are present,
thereby preventing the
accidental
erasure
of
material recorded on the
tape. When the REC/
PLAY button is pressed
115
at a section of the tape on
which material has been
recorded, the tape will
travel, however the REC/
116
PLAY button will flash, an
alarm will sound and
recording will not be
performed.
117
R/P
Heads
PRE_CTL
Head
The underline on the setting item denotes the initial setting.
(continued)
Item
Setting
Superimposed
Superimposed
No.
display
display
FRZ MODE
0000
SEL
0001
0002
REC INH
0000
0001
0002
REC INH
0000
LAMP
0001
EJECT SW
0000
INH
0001
EJECT LAMP
0000
0001
M CASSTT
0000
INH
0001
– 78 –
This selects the output picture in the STANDBY OFF mode
DIS
established from the playback picture and the EJECT mode.
STBOFF
SOF&EJ
0: The video output is muted.
1: The picture being played back is frozen and output in the
STANDBY OFF mode only.
2: The picture being played back is frozen and output in the
STANDBY OFF mode and EJECT mode.
<Notes>
• The status when the picture is frozen complies with what has
been selected for the setup menu item No.604 (FREEZE
SEL) setting.
• In the EJECT mode, the frozen picture is output only when 1
(BLACK) or 2 (GRAY) has been selected as the setup menu
item No.106 (EJECT EE SEL) setting.
• When transferred to EJECT mode, FREEZE will be forcibly
canceled in case of change in output format of HD serial
output.
OFF
This selects whether to allow or inhibit recording on the
cassette tape.
ON
0: Recording on the tape is allowed when its accidental
PRE
erasure prevention tab has been set to the recording
enable position.
1: Recording on the tape is inhibited.
2: Inhibits overwriting during normal recording.
<Note>
"PRE" functions to avoid accidental erasure. With this setting,
the REC INHIBIT lamp flashes continuously. (The lamp
flashes in approx. 0.5 sec cycles)
LIGHT
This selects whether to cause the REC INHIBIT lamp to flash
FLASH
or light up when the cassette's tab has been set to the
recording inhibit position.
0: The lamp lights.
1: The lamp flashes. (The lamp flashes in approx.1 second
cycles.)
<Notes>
• When "1" (ON) has been selected as the setup menu item
No.113 (REC INH) setting, the REC INHIBIT lamp lights all
the time regardless of this setting.
• When "2" (PRE) has been selected as the setup menu item
No.113 (REC INH) setting, the REC INHIBIT lamp flashes all
the time regardless of this setting.(The lamp flashes in
approx. 0.5 second cycles.)
This selects whether to enable or disable the operation of the
REC
eject button on the front panel.
OFF
0: The button's operation is inhibited in the recording mode.
1: The button can be operated in any mode.
This selects whether EJECT lamp is kept lighting or turned off
MODE1
MODE2
in a state of cassette out.
0: EJECT lamp is kept lighting.
1: EJECT lamp is turned off.
OFF
It selects inhibit/permit of recording onto M cassette tape.
0: Recording onto M cassette tape is possible.
ON
1: Recording onto M cassette tape is inhibited.
<Note>
With 0 (OFF) selected, the status of inhibit/permit of recording
onto cassette tape depends on the setting of setup menu
No.113 (REC INH).
Description
Advertisement
Table of Contents
