Forced Arming; Arming In The 'Latchkey' Mode; Initiating A Panic Alarm; Initiating Fire Alarm - Visonic POWERMAX User Manual

If you wish to arm HOME-INSTANT, proceed as follows:
Action
A R M I N G H O M E
A R M I N G I N S T A N T
A R M I N G H O M E
Go to an interior
zone
A R M H O M E
A R M H O M E I N S T A N T
ARM indicator flashes throughout the armed state

2.8 Forced Arming

Forced arming allows you to arm the system even though
one zone or several zones are disturbed, and the NOT
READY message is displayed.
Automatic forced arming only works if the installer allowed
this option while programming your system. Disturbed
zones will be bypassed - they will not be armed. The
protected site will not have maximum protection.
Note: When forced arming is carried out, the buzzer
"protests" by emitting a continuous tone during the exit
delay until the last 10 seconds of the delay. You can
silence this signal by pressing the arming button again.
Forced arming "AWAY" proceeds as follows:
Action
N O T R E A D Y T O A R M
A R M I N G A W A Y
P L E A S E E X I T N O W
(to mute the buzzer)
ARM indicator lights throughout the armed state
Forced arming HOME proceeds as follows:
Action
N O T R E A D Y T O A R M
A R M I N G H O M E
(to mute the buzzer)
H O M E
Go to an interior
zone
ARM indicator flashes throughout the armed state
2.9 Arming in the Latchkey
This mode is useful for a parent at work who wants to be
sure that his children have returned from school and have
disarmed the system. Arming in the "latchkey" mode
means that a special "latchkey" message ill be sent out
when the system is disarmed by a "latchkey user".
Latchkey users are holders of user codes 5 through 8 or
users of Keyfob transmitters 5 through 8. The latchkey
message is considered an alert and not an alarm, and is
therefore sent to the private telephones programmed by
the user as targets for alert messages.
8
Resultant Display
(alternating)
(Exit Delay)
H H : M M
(alternating)
Resultant Display
(Exit Delay)
A W A Y
Resultant Display
(Exit Delay)
H H : M M
Latchkey arming is possible only when you arm "AWAY".
To arm in the Latchkey mode, proceed as follows:
Sound
Action
(within 2 seconds)
! !
Vacate the premises
ARM indicator lights throughout the armed state

2.10 Initiating a Panic Alarm

You can generate a panic alarm manually in the disarmed
and armed states alike. The sequence will be as shown:
Action
(pressed
simultaneously)
Note: If you are using a key-ring transmitter, press both
AWAY and HOME buttons simultaneously for 2 seconds.
To stop the alarm, press
valid user code.

2.11 Initiating Fire Alarm

Sound
You can generate a fire alarm manually (depends on the
purchased PowerMax version - see PowerMax door label)
in the disarmed and armed states alike, if this feature has
been enabled by the installer (consult your installation
company to determine if it has been enabled). The
sequence will be as shown:
Action
Sound
To stop the alarm, press
valid user code.

2.12 Initiating Emergency Alarm

You can generate an emergency alarm manually (depends
on the purchased PowerMax version - see PowerMax door
label) in the disarmed and armed states alike. The
sequence will be as shown:
Action
To stop the alarm, press
valid user code.
Resultant Display
A R M I N G A W A Y
A R M I N G L A T C H K E Y
(alternating)
P L E A S E E X I T N O W
(Exit Delay)
A W A Y
Resultant Display
P A N I C A L A R M
Then, if or when the system is
in the disarmed state:
R E A D Y H H : M M
and then key in your
Resultant Display
F I R E
Then, if or when the system is
in the disarmed state:
R E A D Y H H : M M
and then key in your
Resultant Display
E M E R G E N C Y
Then, if or when the system is
in the disarmed state:
R E A D Y H H : M M
and then key in your
Sound
! !
Sound
Siren
Sound
Siren
Sound
DE5450U