Arming 'Instant; Forced Arming; Arming In The Latchkey Mode; Initiating A Panic Alarm - Visonic powermax+ User Manual

Fully supervised wireless alarm control system
Hide thumbs Also See for powermax+:
Table of Contents

Advertisement

2.7 Arming 'Instant'

You may arm AWAY or HOME without an entry delay - any
detection in any zone will trigger an immediate alarm.
If you wish to arm AWAY-INSTANT, proceed as follows.
Action
A R M I N G A W A Y
A R M I N G I N S T A N T
P L E A S E E X I T N O W
Vacate the premises
A W A Y
ARM lights throughout the armed state
If you wish to arm HOME-INSTANT, proceed as follows:
Action
A R M I N G H O M E
A R M I N G I N S T A N T
A R M I N G H O M E
Go to an interior zone
A R M H O M E
A R M H O M E I N S T A N T
ARM indicator flashes throughout the armed state

2.8 Forced Arming

(Not to be used in UL- listed systems)
Forced arming allows you to arm the system even though
one zone or several zones are disturbed, and the NOT
READY message is displayed.
Automatic forced arming only works if the installer allowed
this option while programming your system. Disturbed
zones will be bypassed - they will not be armed. The
protected site will not have maximum protection.
Note: When forced arming is carried out, the buzzer
"protests" by emitting a continuous tone during the exit
delay until the last 10 seconds of the delay. You can
silence this signal by pressing the arming button again.
When NOT READY is displayed, Forced arming "AWAY"
is performed as follows:
Action
A R M I N G A W A Y
P L E A S E E X I T N O W
(to mute the buzzer)
A W A Y
ARM indicator lights throughout the armed state
When NOT READY is displayed, Forced arming "HOME"
is performed as follows:
Action
A R M I N G H O M E
(to mute the buzzer)
H O M E
Go to an interior zone
ARM indicator flashes throughout the armed state
8
Resultant Display
(alternating)
(Exit Delay)
Resultant Display
(alternating)
(Exit Delay)
H H : M M
(alternating)
Resultant Display
(Exit Delay)
Resultant Display
(Exit Delay)
H H : M M

2.9 Arming in the Latchkey Mode

(Not to be used in UL-listed systems)
This mode is useful for a parent at work who wants to be
sure that his children have returned from school and have
disarmed the system. Arming in the "latchkey" mode
Sound
means that a special "latchkey" message will be sent out
when the system is disarmed by a "latchkey user".
Latchkey users are holders of user codes 5 through 8 or
users of Keyfob transmitters 5 through 8. The latchkey
message is considered an alert and not an alarm, and is
therefore sent to the private telephones programmed by
the user as targets for alert messages.
! !
Latchkey arming is possible only when you arm "AWAY".
To arm in the Latchkey mode, proceed as follows:
Action
Sound
(within 2 seconds)
Vacate the premises
! !
ARM indicator lights throughout the armed state

2.10 Initiating a Panic Alarm

You can generate a panic alarm manually in the disarmed
and armed states alike. If this feature has been enabled by
the installer (consult your installation company to determine
if it has been enabled).The sequence will be as shown:
Action
(pressed
simultaneously)
Note: If you are using a key-ring transmitter, press both
AWAY and HOME buttons simultaneously for 2 seconds.
To stop the alarm, press
valid user code.

2.11 Initiating Fire Alarm

You can generate a fire alarm manually (depends on the
purchased PowerMax+ version - see PowerMax+ door
label) in disarmed & armed states, as follows:
Action
Sound
EMERGENCY
To stop the alarm, press
valid user code.

2.12 Initiating Emergency Alarm

You can generate an emergency alarm manually (depends
on the purchased system version - see PowerMax+ door
label) in the disarmed and armed states as follows:
Sound
Action
EMERGENCY
Resultant Display
A R M I N G A W A Y
A R M I N G L A T C H K E Y
(alternating)
P L E A S E E X I T N O W
(Exit Delay)
A W A Y
Resultant Display
P A N I C A L A R M
Then, if or when the system is
in the disarmed state:
R E A D Y
H H : M M
and then key in your
Resultant Display
FIRE
F I R E
Then, if or when the system is
in the disarmed state:
R E A D Y
H H : M M
and then key in your
Resultant Display
FIRE
E M E R G E N C Y
Then, if or when the system is
in the disarmed state:
R E A D Y
H H : M M
Sound
! !
Sound
Siren
Sound
Siren
Sound
DE5467U

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the powermax+ and is the answer not in the manual?

Table of Contents

Save PDF