Korg D1600mkII Owner's Manual page 170

If "TempoSource" is set to "TempoTrack," has MIDI
clock or tap tempo been recorded on the tempo track?
(→p.73)
Are the synchronization settings of your MIDI
sequencer correct?
→ Refer to the owner's manual of your MIDI sequencer.
The D1600mkII does not receive MMC
In the [SYSTEM/USB] "MIDI" tab page, is
"RcvMMC" turned "On"?
In the above-listed page, does the "MMCDevID" set-
ting match the MMC device ID of your MIDI
sequencer? (→p.87, 93)
The settings required on your MIDI sequencer
will depend on the one you are using.
Has your MIDI sequencer been set to transmit MMC?
→ Refer to the owner's manual of your MIDI sequencer.
Can't control effects/scenes via MIDI
Do the MIDI channels of the D1600mkII and your
MIDI sequencer match?
→ In the [SYSTEM/USB] "MIDI" tab page, check
"GlobalCh."
The D1600mkII does not synchronize as a slave
→ If the D1600mkII is set as a MTC slave, several
seconds may be required before synchronization is
achieved.
Can't control other devices via MMC
In the [SYSTEM/USB] "MMC" tab page, is "Select
MMC Mode" set to "Transmit"?
Is the device receiving MMC set correctly to receive
MMC?
The D1600mkII does not transmit mixer parameters
In the [SYSTEM/USB] "MIDI" tab page, is the
"ControlChange" parameter "Trans" turned on?
Is the device receiving control changes set to record
MIDI channels 1–16?
The D1600mkII does not receive mixer parameters
In the [SYSTEM/USB] "MIDI" tab page, is the
"ControlChange" parameter "Recv" turned on?
WAV
Can't preview
Is the WAV file format supported?
→ Select and preview a WAV file of a format that is
supported. (→p.79, 106)
USB
Computer does not detect the D1600mkII
Is the USB cable connected correctly? (→p.7, 85)
Is the D1600mkII in USB mode? (→p.85)
Depending on the hardware system of the computer
you are using, it may not be able to detect the
D1600mkII in some cases.
An error occurs when you disconnect the computer
Use the correct procedure when disconnecting.
(→p.85)
162
When you connect, you are asked to install software or
a device driver
Does the version of the operating system on your
computer support the D1600mkII? (→p.85, 96)
CD-R/RW
CD-R/RW drive is not detected
Did you subject the D1600mkII to vibration or impact?
The CD-R/RW drive in the D1600mkII is a removable
unit.
→ Check that the CD-R/RW drive is installed correctly.
(→p.166)
Can't write
You can't write any more data to a CD-R/RW disc that
has been finalized.
You can't write to a CD-RW disc that contains data
created by another device.
Writing to the CD failed.
→ Try lowering the CD-R/RW writing speed.
→ Try different media.
Can't play the disc in an audio CD player
Did you finalize the disc?
→ In the [SONG/CD] "CDR/RW" tab page to finalize
the disc. (→p.34, 59)
Did you use CD-R media?
→ Since some CD players are unable to play back CD-
RW media, we recommend that you use CD-R media.
Try a different type of media.
→ Even when you use the recommended CD-R/RW
media, some CD players are unable to play certain
types. The player may be able to play the disc if you
use a different type of media.
Can't back up to CD-R/RW
Are you using a blank disc?
→ If using CD-R, use new (unused) media. If using CD-
RW, use the [SONG/CD] "CDR/RW" tab page
"Erase" button to erase the contents of the media
before you execute the backup.