Korg D1600mkII Owner's Manual page 150

Fc (Side PEQ Cutoff [Hz]) .20...12.0k Sets the EQ center frequency for
Q (Q)...................................0.5...10.0 Sets the EQ bandwidth for the
Gain (Gain [dB])........... –18.0...+18.0 Sets the EQ gain for the trigger
142
the trigger signal
trigger signal
signal
: Envelope Select
When "L/R Mix" is selected for this parameter, the left and right
channels are linked to control the Limiter using the mixed signal. If
"L Only" (or "R Only") is selected, the left and right channels are
linked, and the Limiter is controlled via only the left (or right) chan-
nel.
With "Indivi", the left and right channels control the Limiter indi-
vidually.
: Ratio, : Threshold [dB], : Gain Adjust [dB]
This parameter sets the signal compression "Ratio". Compression is
applied only when the signal level exceeds the "Threshold" value.
In the case of the limiter, applying compression will lower the over-
all level, so you should use "Gain Adjust" to make adjustments.
: Attack, : Release
These parameters set the attack time and release time. A higher
attack time will cause the compression to be applied more slowly.
: Side PEQ Insert, : Side PEQ Cutoff [Hz], : Q, : Gain [dB]
These parameters are used to set the EQ applied to the trigger signal.
The Limiter determines whether the compression is applied, based
on the post-EQ trigger signal. Setting the equalizer allows you to set
the Limiter to respond to any frequency band.
: Trigger Monitor
Setting this parameter "On" will cause the trigger signal to be out-
put, instead of the effect sound. Use this parameter to check the trig-
ger signal with EQ applied.
Usually, set this to "Off."
23: DY3: Multiband Limiter
This effect applies the Limiter to the low range, mid range, and
high range of the input signal. You can control dynamics for
each range to adjust the sound pressure of the low range, mid
range, and high range in a different way from the EQ.
Ratio (Ratio)........ 1.0:1...50.0:1, Inf:1 Sets the signal compression ratio
Thrshl (Threshold [dB]) .......... –40...0 Sets the level above which the
Attack (Attack)........................ 1...100 Sets the attack time
Relse (Release) ..................... 1...100 Sets the release time
LoOfst (Low Offset [dB]) ........ –40...0 Sets the low range gain of trigger
MdOfst (Mid Offset [dB]) ........ –40...0 Sets the mid range gain of trigger
HiOfst (High Offset [dB]) ........ –40...0 Sets the high range gain of trig-
GLevel (Gain Adjust [dB]) ....... –Inf, –
38...+24
Mix (Wet/Dry) ....Dry, 1:99...99:1, Wet Sets the balance between the
: Low Offset [dB], : Mid Offset [dB], : High Offset [dB]
These parameters set the gain of the trigger signal.
For example, if you do not want to apply compression to the high
range, reduce the "High Offset" value down below the "Threshold"
level. In this way, the high range limiter will not respond, and com-
pression will not be applied.
24: DY4: St.Gate
(Stereo Gate)
This effect mutes the input signal if its level is lower than the
specified level. It also reverses the on and off operation of the
gate, and uses Note On and Off messages to turn the gate on
and off.
Envelp (Envelope Select)... L/RMix, L
Only,
R Only
Polrty (Polarity) ........................... +, – Switches between non-reversed
Thrshl (Threshold) ................. 0...100 Sets the level to which the Gate
Attack (Attack)........................ 1...100 Sets the attack time
Relse (Release) ..................... 1...100 Sets the release time
compressor is applied
signal
signal
ger signal
Sets the output gain
effect and dry sounds
Selects from Control via the mod-
ulation source, mixing the left and
right signals, Only left, and Only
right
and reversed Gate on/off
is applied