Installation; Section A: Before You Begin; Important Message; Before You Start - Montigo H36PVN Installation & Maintenance Manual

H36PVN Power Vent Indoor Gas Fireplace
Section A: Before You Begin Section:

Important Message

Save these Instructions
The H36PV Power Vent fireplaces must be installed in
accordance with these Instructions . Carefully read all the
Instructions in this manual first . Consult the Local Gas Branch to
determine the need for a permit prior to starting the installation .
It is the responsibility of the installer to ensure this fireplace is
installed in compliance with the manufacturers instructions and
all applicable codes .
BEFORE YOU START:
XW2016
Due to high operating temperatures, this appliance
should be located out of traffic & away from
Blank
furniture and draperies.
Flammable materials Explosion risk
Children and adults should be alerted to the
hazards of the high surface temperature, which
General Warning Laser Radiation
Blank
could cause burns or clothing ignition.
Irritant Slippery floor
Flammable materials Explosion risk
Young children should be carefully supervised
Gas bottles Watch for
falling objects
Blank
General Warning when they are in the same room as the appliance. Laser Radiation
Low temperature Strong magnetic field
Flammable materials Explosion risk
Clothing or other flammable materials should not
Irritant Slippery floor
be placed on or near the appliance.
General Warning Laser Radiation
Gas bottles Watch for
falling objects
Irritant Slippery floor
XW2020-When-Installed_[EN].pdf
Low temperature Strong magnetic field
XW2018
Gas bottles Watch for
XW2020
Page 4

Installation

NOTICE
Installation and repairs should be done by an
authorized gas fireplace service technician. The
appliance should be inspected before use and at
least annually by a professional. More frequesnt
cleaning may be required due to exessive lint from
carpeting, bedding material, ect. It is imperative
that control compartments, burners and circulating
air passageways of the fireplace are kept clean.
CAUTION
Toxic Corrosive Danger overhead crane Fork lift trucks High voltage
Biohazard Oxidising Hot surface Danger of entrapment Danger of death
Watch your step Cutting High temperatures Glass hazard Danger of suffocation
Toxic Corrosive Danger overhead crane Fork lift trucks High voltage
Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
Biohazard Oxidising Hot surface Danger of entrapment Danger of death
Optical radiation Non ionizing Radiation Hazardous to the Danger of harming
radiation Environment your hands
Toxic Corrosive Danger overhead crane Fork lift trucks High voltage
Watch your step Cutting High temperatures Glass hazard Danger of suffocation
Biohazard Oxidising Hot surface Danger of entrapment Danger of death
Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
Watch your step Cutting High temperatures Glass hazard Danger of suffocation
1 1/24/2011 12:48:53 PM
Optical radiation Non ionizing Radiation Hazardous to the Danger of harming
radiation Environment your hands
Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
DANGER
When this appliance is installed directly
on any combustible material other than
wood flooring, it must be installed on a
metal or wood panel extending the full
width and depth of the appliance or a
fire will occur causing serious injury,
property damage or even death.

Pre-Installation Checklist

■ Determine the desired install location of your fireplace .
■ See Section 1, Dimensions on Page 5, and refer to the
Framing Section 2 for details .
■ Select your type and location of your Power Vent
run: Roof Mounted (EDVRSPV58) or Wall Mounted
(EDVWSPV58) .
■ Your termination location should be selected to provide
the shortest possible vent run .
■ Lay out the Vent run; calculating the required elbows
and straight runs of 5"/8" flex or rigid pipe .
■ Refer to the Section 4 on Page 10, "Installing the Power
Vent" for details .
■ Montigo supplies 20' of low voltage wire, which can be
spliced to any length . This wire CANNOT run in conduit
with any other wire .
■ Refer to Section 5 on Page 18, for Wiring Details .
■ The gas connection is located on the bottom side of the
fireplace .
■ Refer to local codes and guidelines for installation
requirements .
■ Installation and repairs should be done by a qualified
contractor and must conform to:
• I nstallations in Canada must conform to the current
CAN/CGA B-149 .1 and .2 Gas Installation Code and
local regulations .
• I nstallations in the USA must conform to local
codes, or in the absence of local codes to the National
Fuel Gas Code, ANSI Z223 .1-1988 .
• S ee Appendix C for installation within the State
of Massachusetts. This fireplace must comply with
NFPA-54 Chapter 10 .
■ Refer to Section 6 Page 21, "Installing the Gas Line" for
Details .
Understanding the Basic Operation
Residential H36PV fireplace
To operate the fireplace, Montigo has supplied and installed
twenty feet of low voltage wire to this electrical control panel .
Connect the two wire harness to a standard single pole ON/
Off switch located at a location of your choice . You may also
extent these wires to any length, as long as you select a wire
of equal quality .
XG0649 - 031511