ProScan PS35652 Owner's Manual page 30

VCR Channel Setup
The VCR 1CHAN function lets you program to which channe!
the TV will automatically tune when you press the vcm
button on the remote. This is handy if you connect a VCR
to your TV. You will no
longer
have to remember to which
input jacks
the VCR is connected because the TV will
remember for you+
For example, if you connect a VCR's AUOiONIOEO OUT jacks
to the TV's tNPUT 1jacks (as shown on page 46), you will
no longer have to remember to select channel 91 on the TV
to see what the VCR is playing. By entering channel 91
next to the VCR+CHANfunction, the TV will automatically
tune to channel 91 each time you press the VCR1button on
- the remote.
This function is especially convenient if you have a
compatible VCR that can be operated by the vcR1 button on
the remote. Pressing vcm will then not only turn on the
VCR but also automatically tune the TV to the proper
channel for viewing the picture from the VCR. You can
program most brands of remote-controllable VCR's to
respond to the VCR'+ b utton as described on page 31+
The vca 2 CHAN function works the same way. It lets you
program to which channel the TV will automatically tune
when you press the VCR2/LD button on the remote. You can
progatn most brands of remote-controllable VCR's to
respond to the VCR2/LD b utton as described on page 31.
Pressing the VCR2/LD button will then not only turn on the
VCR but also automatically tune the TV to the proper
channel for viewing the picture from the VCR.
Setting Up VCR Channels
with or without remote
1 Repeatedly press the MENUbutton to select SETUPMENUand
then press + to display the setup functions.
Enter the channel number you
want to program by pressing two
number buttons on the remote
control. (The channel number
you enter is the channel to which
the TV will tune automatically
when you later press the VCR1button on the remote.) See the
notes below if you are unsure about which channel number to
enter.
Press the + button to program the
channel number you selected into
the TV's memory.
Note: Pressing the - button here will
turn offthis t;ealure and display vca 1
CHAN: O FFagain.
5 If you have another VCR
connected to the TV, press MENU
to select the VCR2 CHANfunction,
6
Enter the channel number you
want to program by pressing two
number buttons on the remote
control. (This is the channel
number to which the TV will tune
automatically when you later
press the VCR2/LD button on the remote). See the notes below
if you are unsure about which channel number to enter.
7 Press the + button to program the
channel number you selected into
the VCR2 CHANfunction memory.
Note.* Pressing the button here wilt
turn oft" this feature and display veR
2 CHAN: OFF
again.
2 Repeatedly press MENUto select the VCR_ CHANfunction.
Notes about Entering Channel Number:
• Enter channel 91 if your VCR is connected to the TV's audio and video
INPUTI jacks,
• Enter channel 92 if your VCR is connected to the TV's audio and video
_NPUT 2 jacks.
• Enter channel _ if you have a Su_r+VHS VCR that is connected to
the WV's S+v!oEOconnector and INPUT_ audio jacks (labeled Land
R/MONO)+
• Enter channel 03 (or 04) it"you did not use any audio/video cables and
connected the VCR to the TV's round antenna connector labeled
CABLE/ANT[NNA,
Enter the same channel number (03 or 04) as the
position of the VCR's CHa/CH4 switch. This is the channel to which
you must tune your TV for viewing signals from your VCR+
• Refer to pages 4647 if you want m review details about connecting
your VCR to your TV.