ProScan PSVR64 Owner's Manual page 15

Startu p
Auto Cable/DSS Box Setup
The cable/DSS box setup allows the VCR to record programs from the cable box or RCA
DSS ® receiver.
• If your cable box can be controlled by a remote, the VCR may be able to tune it to
the channel you want to record during VCR Plus+ and timer recordings. Position
the remote-controllable cable box on top of the VCR to receive the infrared remote
signal. (See pages 3-4.)
• The VCR will turn on an RCA DSS® receiver and tune it to the channel you want
to record during timer recordings. Position the receiver on top of the VCR to
receive the infrared remote signal. (See pages 5-7.)
1. Cable box or satellite receiver not used for all channels:
Press 2. You are finished with Cable Box Setup. Skip to Auto Channel Search and
Auto Clock Set.
Cable box or RCA DSS ® receiver used for all channels:
Press 1 to continue.
2. Press two numbers on the remote to enter the output channel of your cable box
or satellite receiver. Press 0 before a single-digit number.
Valid numbers are 01 - 99.
If you connected your cable box or satellite receiver to the VCR using the box's
AUDIO/VIDEO OUT jacks, press INPUT to select the VIDEO1 or VIDEO2 option.
Press CLEAR on the remote to correct an entry.
3. Press MENU°PROG to proceed.
The VCR now automatically enters the output channel of your cable box or
satellite receiver as the channel to be recorded in the VCR PLUS+ and Timer
Recordings menus,
4. Press MENU°PROG to proceed.
5. Manually Controlled Cable Box: You are finished with cable box setup. Press
MENU °PROG to exit. Proceed to Auto Channel Search and Auto Clock Set.
RCA DSS ® Receiver or Remote Controlled Cable Box:
• RCA DSS® Receiver: Enter 00 for the code. The receiver should turn on and
tune to channel 200.
The VCR will now tune your receiver to the correct channel during timer
recordings. - - - DSS will appear for the channel in the timer program menu.
Auto clock set is not supported by DSS. Proceed to Manual Clock Set, and
manually set the clock.
Remote Controlled Cable Box: Enter your cable box code from the chart on page
21 and follow the on-screen directions.
The VCR changes the cable box from channel 02 to channel 09 when you enter the
correct code for your cable box.
If the cable box changes channels, press 1. Proceed to Auto Channel Search and
Auto Clock Set.
If none of the codes work, try repositioning the cable box and entering the codes
again. If the codes still do not work, this VCR cannot control your cable box
during timer recordings or automatically set the clock. Press MENU,PROG.
Proceed to Auto Channel Search andAuto Clock Set.
SETUP
Is a cabLe box or DSS
receiver being used
with the VCR'foP aLL
channels?
::: _ _................. L_ :_..............
2 No, skip this step
CABLE/DSS BOX SETUP
Enter the output
channel of the cable
box or DSS receiver.
Press 01-99 or INPUT
Press RENU to exit
CABLE/DSS BOX SETUP
The V£R wiLL now receive
eLL channels from the
cable box or DSS
receiver on VCR Ch 03
Press RENU to proceed
CABLE/DSS BOX SETUP
Enter the code for
your cabLe box or DSS
receiver from the List
in your U___r's Ranual.
/1\
Press RENU to proceed
Did the DSS receiver
turn on end tune to
channel 200?
1 YES, setup complete
2 NO, try another code
CABLE/DSS BOX SETUP
PLease turn on the
cabLe box and tune it
to channel 2.
Press MENU to proceed
CABLE/DSS BOX SETUP
Did the cable box
tune to channeL 9?
2 NO, try another code |
J
11