Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Setup Manual
Advertisement
Table of Contents
Related Manuals for Epson SureColor SC-F7000
Summary of Contents for Epson SureColor SC-F7000
- Page 1 User’s Guide NPD4829-01 EN...
-
Page 2: Copyrights And Trademarks
(excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. -
Page 3: Table Of Contents
Menu Operations......66 Starting EPSON LFP Remote Panel 2..22 Menu List. - Page 4 Technical Support Web Site....90 Contacting Epson Support....90 Before Contacting Epson.
-
Page 5: Introduction
SC-F7000 Series User’s Guide Introduction ❏ Use only the power cord that comes with this Introduction product. Use of another cord may result in fire or electric shock. ❏ Do not use a damaged or frayed power cord. Important Safety ❏... -
Page 6: When Handling The Ink Packs
SC-F7000 Series User’s Guide Introduction ❏ This device has two power systems. There is a risk of Illustrations electric shock unless the two power cables are unplugged during the maintenance. The illustrations in this manual may differ slightly from the actual objects they are intended to represent. When handling the ink packs Operating System Versions ❏... -
Page 7: Printer Parts
SC-F7000 Series User’s Guide Introduction Printer Parts Front Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. “Cleaning Around the Print Head” on page 54 Eject guide Media is ejected along this guide. Roll core holder Place the used roll core for media take-up on these holders. - Page 8 SC-F7000 Series User’s Guide Introduction Roll support Rest media temporarily on these supports when removing the take-up roll. There are two supports: one on the left and one on the right. Auto switch Use this switch to select the auto take-up direction. Choose Off to disable auto take-up. Manual switch Use this switch to select the manual take-up direction.
- Page 9 SC-F7000 Series User’s Guide Introduction Maintenance cover (right) Open this cover to perform maintenance around the print head. Normally closed when using the printer. “Maintenance Around the Print Head” on page 53 Media loading lever After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media prior to removal.
-
Page 10: Slider
SC-F7000 Series User’s Guide Introduction Slider LAN port Slider Attach the chip unit included with the ink pack before refilling the ink. “Chip Unit Replacement and Ink Refills” on RJ-45 connector page 61 Connects the LAN cable. Use a shielded twisted pair cable (category 5 or higher). -
Page 11: Inside
SC-F7000 Series User’s Guide Introduction Inside Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. Print head The print head prints by moving left and right while emitting ink. Cleaning may be required depending on the status. -
Page 12: Back
SC-F7000 Series User’s Guide Introduction Wiper cleaner The wiper cleaner removes ink from the wiper. It is a consumable; replacement may be required depending on the status. “Replacing the Wiper and Wiper Cleaner” on page 59 Caps Except during printing, these caps cover the print head nozzles to prevent them drying out. Cleaning may be required depending on the status. - Page 13 SC-F7000 Series User’s Guide Introduction Lift lever If the media to be mounted on the roll holders seems heavy, use these levers to raise the media effortlessly to the level of the roll holders. There are two lift levers: one on the left and one on the right. Loading guide Media is loaded along this guide.
-
Page 14: Control Panel
SC-F7000 Series User’s Guide Introduction Display Control panel Displays the printer’s status, menus, error messages, and so on. U “Understanding the Display” on page 15 Menu button Press this button to display menus. U “Using the Control Panel Menu” on page 66 y button (back button) Press this button to exit to the previous menu when options are displayed. -
Page 15: Understanding The Display
SC-F7000 Series User’s Guide Introduction ❏ Pressing this button displays the Maintenance If a media setting bank number created with this printer is selected as the print media, the number menu, which contains such items as Nozzle Check, (from 1 to 30) will be displayed. When RIP Settings is Cleaning, Head Maintenance, and Waste Ink selected, 0 will be displayed. -
Page 16: Features
SC-F7000 Series User’s Guide Introduction BK : Black Features : Yellow This wide-format color ink jet printer supports roll : Magenta media 1626 mm (64 inches) in width. The main features of this printer are described below. : Cyan Realizing High Productivity Waste ink bottle status Displays the approximate amount of space available Media Feeding Unit Accommodates High-Capacity... -
Page 17: Notes On Usage And Storage
SC-F7000 Series User’s Guide Introduction E-Mail Error/Warning Notification Notes on Usage and The EpsonNet Config with Web Browser system built into the printer’s network interface offers e-mail Storage notification. Once configured for e-mail notification, the printer will send errors and warnings to selected e-mail addresses, ensuring peace of mind when the Installation space printer is left unmanned during overnight operation... -
Page 18: Notes When Not Using The Printer
(lid) to prevent the print head from drying out. In Contact your dealer or Epson Support. this case, turn on the power and wait a while until capping is performed automatically. -
Page 19: Notes On Handling Ink Packs And Ink Tanks
SC-F7000 Series User’s Guide Introduction ❏ Close all covers before placing the printer in Handling Media storage. If you are not using the printer for a long time, put an anti-static cloth or cover on the printer Note the following when handling or storing media. to prevent dust. - Page 20 SC-F7000 Series User’s Guide Introduction ❏ To prevent discoloration, display and store prints as instructed in the documentation supplied with the media.
-
Page 21: Using The Supplied Software
Installs the Epson communications driver (EPSON SC-F7000 Series Comm Driver). The Epson communications driver is required if the EPSON LFP Remote Panel 2 is to be used to copy media settings. It is not a printer driver. In addition, the software RIP may not display printer status if the Epson communications driver is not installed when the printer is connected to a computer via USB. -
Page 22: Starting Epson Lfp Remote Panel 2
Programs category. Exiting EPSON LFP Remote Panel Select the software you want to remove and then Click Exit in the EPSON LFP Remote Panel 2 main click Uninstall/Change (or Change/Remove). window. Selecting the following deletes the Epson communications drivers. -
Page 23: Basic Operations
SC-F7000 Series User’s Guide Basic Operations When the Standard Media Feeding Basic Operations Unit Is Installed This section describes how to load media when the standard media feeding unit is installed. Loading and Exchanging Media Caution: Because the media is heavy, it should not be carried by one person. - Page 24 SC-F7000 Series User’s Guide Basic Operations Place media on the roll support oriented Raise the lift lever on the left side of the printer to according to how it is rolled (see below) and lift the media into position, then firmly insert the position it as indicated by the mark on the label.
- Page 25 SC-F7000 Series User’s Guide Basic Operations Raise the lift lever on the right side of the printer Rotate the handle until part A in the illustration to lift the media into position, then firmly insert below is fully inserted. the roll holder. If the roll of media has the outer diameter which is less than 140 mm, lift it up by your hands, and set it to the roll holder as described in Step 4.
- Page 26 SC-F7000 Series User’s Guide Basic Operations Go to the front of the printer and open the front Note: cover. Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In Hold the center of the media and raise the media...
- Page 27 SC-F7000 Series User’s Guide Basic Operations For information on loading the media into the Attach the media holding plates at either side of auto take-up reel unit, see: the media. “Using the Auto Take-up Reel Unit” on First, position the plates so that the edges of the page 35 media are in the centers of the round holes.
- Page 28 SC-F7000 Series User’s Guide Basic Operations Turn on the printer by pressing the P button. Important: ❏ Do not use the media holding plates with media that is more than 0.4 mm thick. Loosen the roll holder fixing screws and adjust The media holding plates could touch the roll holders so that the gap between the two is and damage the print head.
- Page 29 SC-F7000 Series User’s Guide Basic Operations Printable Side In Align the media and the roll holders. Raise or lower the lifter until the media roll core is level with the roll holders. Fully insert the left roll holder. Next, tighten the roll holder screw to fix the roll holder in place.
- Page 30 SC-F7000 Series User’s Guide Basic Operations Rotate the handle until part A in the illustration Pull out the media and insert it into the printer. below is fully inserted. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder.
- Page 31 SC-F7000 Series User’s Guide Basic Operations Pull the media straight forward until the edge has past the label on the bottom side of the eject guide. Keep the right edge of the media parallel with the scale markings on the two labels on the eject guide.
-
Page 32: Viewing And Changing Media Settings
SC-F7000 Series User’s Guide Basic Operations Note: Important: ❏ Do not use the media holding plates with If you would prefer to print from the very start of the media that is more than 0.4 mm thick. roll, press the u button in the control panel to The media holding plates could touch rewind the media slightly. -
Page 33: Exchanging Media
SC-F7000 Series User’s Guide Basic Operations ❏ Remaining Setup Select an option. On: The printer displays the amount of media To print at current settings: remaining. Use the d/u buttons to select Keep Settings Above and press the Z button. Off: The printer does not display the amount of media remaining. -
Page 34: Cutting Media
SC-F7000 Series User’s Guide Basic Operations You can print the amount of media remaining on the Caution: leading edge of the roll before it is removed from the When cutting media, be careful not to cut your printer and then enter this number the next time the fingers or hands with the cutter or other blades. -
Page 35: Using The Auto Take-Up Reel Unit
SC-F7000 Series User’s Guide Basic Operations Removing Media Remove the media holding plates. You can now remove the media from the roll holders. To remove the media, reverse the steps you followed to load Using the Auto Take-up Reel Unit Media Loading and Take Up The auto take-up reel unit automatically takes up media as it is printed, improving the efficiency of unmanned... - Page 36 SC-F7000 Series User’s Guide Basic Operations Align the right roll core holder with the right Caution: edge of the media and tighten the locking screw. ❏ Be sure that your hands or hair do not get caught in the auto take-up reel unit while it is in operation.
- Page 37 SC-F7000 Series User’s Guide Basic Operations Press the d button in the control panel to feed Important: enough media for a single wrap around the roll Stop when part A is no longer visible. The core. take-up reel unit may not function as expected if the holder is inserted too far.
- Page 38 SC-F7000 Series User’s Guide Basic Operations Flip the Auto switch to Confirm that the media is attached without deformation. As shown in the identified sections in the illustration below, if the tensions of the left and right edges of the media are different, the media cannot be taken up correctly.
- Page 39 SC-F7000 Series User’s Guide Basic Operations When attaching on the left and right, attach using Important: tape while pulling the media straight down. Confirm that edges of media taken up on the roll core are not misaligned. If the edges are misaligned, the media that follows cannot be taken up correctly.
-
Page 40: Removing The Take-Up Roll
SC-F7000 Series User’s Guide Basic Operations Lower the tensioner. Press the d button to feed the media until the take up roll core begins to turn. Important: The auto take-up reel unit will not function if the tensioner is raised. Removing the Take-up Roll The procedure for removing media varies depending on whether you are using the installed auto take-up reel... - Page 41 SC-F7000 Series User’s Guide Basic Operations Loosen the left roll core holder locking screw and Lower the roll onto the roll support. remove the roll core holder from the roll. Using the Optional Heavy Roll Auto Lower the roll onto the roll support. Take-up Reel Unit This section explains how to remove media from the take-up reel using a lifter.
-
Page 42: Before Printing
SC-F7000 Series User’s Guide Basic Operations Perform head cleaning if parts of the pattern are faint or Insert the lifter between the media and the auto missing. take-up reel unit and adjust the height to support the take-up roll. Print a Check Pattern U “Checking for clogged nozzles”... -
Page 43: Saving Settings
SC-F7000 Series User’s Guide Basic Operations ❏ Feed Speed Setting Name Name the media setting bank. Using distinctive names For more information on these items, see U “The makes it easier to select banks for use. Media Setup Menu” on page Select Setting Name and press the Z button. -
Page 44: Head Alignment
SC-F7000 Series User’s Guide Basic Operations Head Alignment Press the y button to return to the customize settings menu. Select Head Alignment to realign the print head when print results seem grainy or out of focus. Head Movement For Head Alignment, you need to check the pattern and Choose the range in which the print head moves during enter the optimum adjustment value for alignment. -
Page 45: Correcting Print Misalignment (Head Alignment)
SC-F7000 Series User’s Guide Basic Operations Tension Measurement Press the y button to return to the customize settings menu. Periodically is recommended in most circumstances. Choose Off if slack develops in the media or other Exiting the Menus printing problems occur. Press W to exit the menus. -
Page 46: Feed Adjustment
SC-F7000 Series User’s Guide Basic Operations Use the d/u buttons to select a media setting When C1 is displayed in the control panel, use bank number between 1 and 30 and then press the d/u buttons to select the number recorded in the Z button. -
Page 47: Using A Test Pattern
SC-F7000 Series User’s Guide Basic Operations The printer will print a test pattern. Using a Test Pattern When printing is complete, the media will Buttons that are used in the following settings automatically be fed to a position where the pattern is clearly visible. -
Page 48: Performing Feed Adjustment During Printing
SC-F7000 Series User’s Guide Basic Operations Printable area Performing Feed Adjustment During Printing The gray area in the illustration below shows the Buttons that are used in the following settings printable area. The arrow indicates the feed direction. The positions of items are as follows: (right edge of media) Varies with the option selected for Media Size... - Page 49 SC-F7000 Series User’s Guide Basic Operations 300-1626mm 3-25mm* 3-825mm* 1 The value selected for Side Margin(Left) in the setup menu. The default value is 5 mm. Choose a Side Margin(Left) over 10 mm when using media holding plates. 2 The total of the values selected for Print Start Position and Side Margin(Right) in the setup menu.
-
Page 50: Maintenance
SC-F7000 Series User’s Guide Maintenance Clean the pressure rollers. Maintenance Remove particles of paper and dust from the pressure rollers using a soft-bristled brush. Daily Maintenance To maintain print quality, perform the following inspection and cleaning before starting work each day. Cleaning the Platen, Pressure Rollers, and Media Holding Plates... -
Page 51: Checking For Clogged Nozzles
SC-F7000 Series User’s Guide Maintenance Select Nozzle Check and press the Z button. Checking for clogged nozzles We recommend that you check the nozzles for clogs A nozzle pattern will be printed. each time you print to ensure quality results. When printing is complete, the media will Ways to Check for Clogs automatically be fed to a position where the... - Page 52 SC-F7000 Series User’s Guide Maintenance There is no need to clean the head if the print result does not contain faint areas or other color problems. Buttons that are used in the following settings You can also clean the head while printing is paused. Note, however, that hues in the printout may change when printing is resumed.
-
Page 53: Maintenance Around The Print Head
SC-F7000 Series User’s Guide Maintenance ❏ A clean room wiper (available in the market) Head cleaning will be performed. A lint-free (non-woven) cleaning cloth. Use to The menu will close when cleaning is complete. clean around the print head. Print a nozzle pattern and inspect the results to determine whether the problem has been ❏... -
Page 54: Cleaning Around The Print Head
SC-F7000 Series User’s Guide Maintenance Open the maintenance covers at each end. Clean the parts in the following order. (1) Print head (2) Wiper (3) Caps (4) Wiper rail Cleaning Around the Print Head Moving the Print Head Inspect the area around the print head and remove any This section describes how to position the print head for ink stains as described below. - Page 55 SC-F7000 Series User’s Guide Maintenance If there is ink on the attachment points, remove Ink spatters on the base of the print head can be the wiper for cleaning. Proceed to Step 2. removed using a clean room wiper (available in the market).
-
Page 56: Cleaning The Wiper Rail
SC-F7000 Series User’s Guide Maintenance Clean the front and back of the wiper with a Return the wiper when cleaning is complete. cleaning stick. Place on the attachment point and press down until you hear a click. Clean the bottom of the wiper with a cleaning stick. -
Page 57: Disposing Of Waste Ink
SC-F7000 Series User’s Guide Maintenance When Press Z after cleaning. is displayed on Return the wiper cleaner that was removed in Step 2 to its original position. the control panel and the Z button is pressed, the wiper moves to the back. Place on the attachment point and press down until you hear a click. -
Page 58: Replacing The Waste Ink Bottle
Material Safety Data Sheet (MSDS) to the industrial waste disposer. You can download it at your local Epson Web site. The printer tracks waste ink and displays a message when the counter reaches the warning level. Reset the waste ink counter after replacing the waste ink bottle. -
Page 59: Replacing The Wiper And Wiper Cleaner
SC-F7000 Series User’s Guide Maintenance Press the Z button. Remove the wiper cleaner. Grasp the cleaner as shown and lift it from the Check again to confirm that a fresh waste ink printer. bottle is correctly placed and then press the Z button to reset the waste ink counter. - Page 60 SC-F7000 Series User’s Guide Maintenance Remove the wiper. The menus will close when the print head returns to its normal position. Holding the wiper by the attachment point, tilt it left and lift it out. Insert new wiper. Remove the cap on the wiping part of the wiper. Place on the attachment point and press down until you hear a click.
-
Page 61: Chip Unit Replacement And Ink Refills
Be sure to read the Material Safety Data Sheet Replacements and Ink Refills (MSDS) before using ink packs. You can download it at your local Epson Web site. If the message Chip unit expended. is displayed on the Should ink contact your skin or enter your eyes... - Page 62 Remove the chip unit from the slider. because fine dirt, dust and other foreign bodies mixed the ink in the ink tank cause the ink tank to malfunction. The ink tank replacement interval depends on the usage environment and conditions. Contact your dealer or Epson Support.
- Page 63 SC-F7000 Series User’s Guide Maintenance Attach the chip unit supplied with the new ink Shake the new ink pack as shown in the pack to the slider. illustration horizontally for approximately 5 cm left and right for 5 seconds approximately 15 Check to confirm that the color of the label on the times.
-
Page 64: Disposal Of Used Consumables
SC-F7000 Series User’s Guide Maintenance Tear off the ink pack spout opening. Important: Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink tanks. This can cause messages from the remaining ink warning system to not be displayed properly. -
Page 65: Parts That Are Periodically Replaced
SC-F7000 Series User’s Guide Maintenance Parts That Are Periodically Replaced The following parts require periodic replacement. The time until the following parts need to be replaced depends on the conditions of use. ❏ Print head ❏ Carriage encoder ❏ Ink holder ❏... -
Page 66: Using The Control Panel Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The menus are used as shown below. -
Page 67: Menu List
SC-F7000 Series User’s Guide Using the Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Menu Item Parameter Media Setup Media Remaining “The Media Remaining Setup On, Off... - Page 68 SC-F7000 Series User’s Guide Using the Control Panel Menu Menu Item Parameter Drying Drying Time Per Pass 0 to 10 sec Media Suction 0 to 10 Head Movement Data Width, Printer Full Width Multi-Strike Printing Off, 2 to 8 Roll Type Printable Side Out, Printable Side In Tension Measurement Periodically, Every Page, Off...
- Page 69 SC-F7000 Series User’s Guide Using the Control Panel Menu Menu Item Parameter Print Logs Print Job Log Sheet Print “The Print Logs Show Total Prints XXXXXX m (XXXXXX ft Menu” on page 75 Printer Status Print Status Sheet Print “The Printer Firmware Version XXXXXXX,X_XX,XXXX Status Menu”...
-
Page 70: Details Of The Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Details of the Menu The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button. indicates default settings. Media Remaining Item Parameter Explanation Remaining Setup Choose On to display and record, or Off to not display and not record, the amount of media remaining. - Page 71 SC-F7000 Series User’s Guide Using the Control Panel Menu RIP Settings Item Parameter Explanation Platen Gap Change Platen Gap (the gap between the print head and the media) for the media setting bank selected in the software RIP. The default setting of 1.5 is recommended in most situations. Choose 2.0 if printout is scratched or smudged.
- Page 72 SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Feed Adjustment Manual Use this option if banding (horizontal banding, lines, or strips of uneven color) persists after head cleaning and head alignment have been performed. Visually inspects the printed pattern and enter the adjustment value by hand.
-
Page 73: Printer Setup Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Tension Measurement Periodically Choose Periodically or Every Page to have the printer automatically monitor and adjust media tension during printing for optimal results, Off Every Page to disable automatic tension adjustment. Periodically is recommended in most circumstances. - Page 74 SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Print Start Position 0 to 800 mm (0.00 Adjust this parameter if you want to print from the near center of the to 32.00 inch) media or if you want to shift the printed area left from the Side Margin(Right) setting.
-
Page 75: The Maintenance Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Sleep Mode 15 to 240 minutes The printer will enter sleep mode if no errors have occurred, no print jobs have been received, and no actions are performed on the control panel for an extended period of time. -
Page 76: The Printer Status Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Show Total Prints Displays the total area of media printed (to a maximum of six XXXXXX m (XXXXXX ft digits). The Printer Status Menu These items track printer use and settings. Item Parameter Explanation... -
Page 77: The Reset All Settings Menu
SC-F7000 Series User’s Guide Using the Control Panel Menu Item Parameter Explanation Language Japanese Select the language used in the control panel display. English French Italian German Portuguese Spanish Dutch Russian Korean Chinese Unit: Length Choose the units of length used in the control panel display and when printing test patterns. -
Page 78: Problem Solver
Use EPSON LFP Remote Panel 2 to update the firmware again. Restart the printer. If this message appears in the control panel again, contact your dealer or Epson Support. Auto Take-up Reel Unit stopped. Media is not correctly attached to the auto take-up reel unit. -
Page 79: When A Maintenance Call/Service Call Occurs
Turn on the printer again multiple times. If the same call for service is displayed on the LCD panel, contact your dealer or Epson Support for assistance. Tell them the call for service code is “XXXX”. -
Page 80: Troubleshooting
SC-F7000 Series User’s Guide Problem Solver You cannot print under the network Troubleshooting environment. You cannot print (because the Are the network settings correct? Ask your network administrator for the network printer does not work) settings. The printer does not turn on. Connect the printer directly to the computer using a USB cable, and then try to print. -
Page 81: The Prints Are Not What You Expected
Are you using a genuine Epson ink pack? skewed and data will appear outside the print area. The printer is designed for use with the genuine Epson Set Media Skew Check to On in the Menu. ink packs specified in this manual. Using any other type of ink pack may result in reduced print quality. -
Page 82: Media
SC-F7000 Series User’s Guide Problem Solver Is the media wide enough for the print data? Is the print head scuffing the printed surface? Although printing normally stops if the print image is Smear caused by the print head scuffing the media wider than the media, data will be printed beyond the can be prevented by adjusting the Platen Gap to suit edges of the media if Off is selected for Media Size... - Page 83 Is Off selected for Tension Measurement? Periodically is recommended in most circumstances. Contact your dealer or Epson Support. “Tension Measurement” on page 45 If the print head is over the media, move it away from the jam.
-
Page 84: Others
SC-F7000 Series User’s Guide Problem Solver Remove any media that remains inside the printer. Turn on the power to the printer and perform a nozzle check. Check the printed check pattern, and if there are any clogs, perform head cleaning. “Checking for clogged nozzles”... -
Page 85: Appendix
Important: Refilling the ink tank with an ink pack not specified in this manual can damage the printer. Epson is not responsible for any damages or injuries incurred through the use of unspecified Epson genuine ink packs, even if the printer is still within warranty. -
Page 86: Supported Media
SC-F7000 Series User’s Guide Appendix Supported Media Moving and Transporting the Printer The following media can be used with the printer. This section describes how to move and transport the Print quality is greatly affected by the type and quality of product. -
Page 87: Transport
Transport Release the caster locks on the left and right legs Before transporting the printer, contact your dealer or and fully raise the adjusters. Epson Support. Move the printer. Important: Use the casters on the dedicated printer stand to move the printer indoors a short distance over a level floor. -
Page 88: System Requirements
SC-F7000 Series User’s Guide Appendix System Requirements Printer Specifications Operating Temperature/Humidity Range Consult the documentation for your software RIP. Specifications Table Printer Specifications Printing method On-demand ink jet Nozzle configuration 360 nozzles × 2 rows × 4 colors (Black, Cyan, Magenta, Yellow) Resolution (maximum) 720 ×... -
Page 89: Standards And Approvals
SC-F7000 Series User’s Guide Appendix Important: The ink will freeze if stored for a long period of time at -20°C or below. If the ink is frozen, store for at least 4 hours at room temperature (25°C) before using.(With no condensation.) Standards and Approvals Safety UL 60950-1... -
Page 90: Where To Get Help
Support Technical Support Web Before Contacting Epson Site If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting Epson’s Technical Support Web Site provides help with information in your product documentation, contact problems that cannot be solved using the Epson support services for assistance. -
Page 91: Help For Users In North America
Internet Support Help for Users in Australia Visit Epson’s support website at http://epson.com/ Epson Australia wishes to provide you with a high level support and select your product for solutions to of customer service. In addition to your product common problems. You can download drivers and... -
Page 92: Help For Users In Singapore
The more information you ❏ Product usage questions or problems prepare, the faster we can help solve the problem. This information includes your Epson product ❏ Enquiries on repair service and warranty documentation, type of computer, operating system, application programs, and any information you feel is required. -
Page 93: Help For Users In Hong Kong
603-56288222 Internet Home Page ❏ Enquiries on repair services & warranty, product Epson Hong Kong has established a local home page in usage and technical support (Techline) both Chinese and English on the Internet to provide users with the following information:... -
Page 94: Help For Users In The Philippines
- 6PM) Prefix local STD code Help for Users in the Philippines To obtain technical support as well as other after sales services, users are welcome to contact the Epson Philippines Corporation at the telephone and fax numbers and e-mail address below:... -
Page 95: Software License Terms
SC-F7000 Series User’s Guide Software License Terms Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version (“Bonjour Programs”). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.2 or its latest version until five (5) years after the discontinuation of same model of this printer product. - Page 96 SC-F7000 Series User’s Guide Software License Terms 1.6 “Modifications” mean any addition to, deletion from, and/or change to, the substance and/or structure of the Original Code, any previous Modifications, the combination of Original Code and any previous Modifications, and/ or any respective portions thereof. When code is released as a series of files, a Modification is: (a) any addition to or deletion from the contents of a file containing Covered Code;...
- Page 97 SC-F7000 Series User’s Guide Software License Terms 2.3 Distribution of Executable Versions. In addition, if You Externally Deploy Covered Code (Original Code and/or Modifications) in object code, executable form only, You must include a prominent notice, in the code itself as well as in related documentation, stating that Source Code of the Covered Code is available under the terms of this License with information on how and where to obtain such Source Code.
- Page 98 SC-F7000 Series User’s Guide Software License Terms 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies.
- Page 99 SC-F7000 Series User’s Guide Software License Terms (c) automatically without notice from Apple if You, at any time during the term of this License, commence an action for patent infringement against Apple; provided that Apple did not first commence an action for patent infringement against You in that instance.
-
Page 100: Other Software Licenses
SC-F7000 Series User’s Guide Software License Terms EXHIBIT A. “Portions Copyright (c) 1999-2003 Apple Computer, Inc. All Rights Reserved. This file contains Original Code and/or Modifications of Original Code as defined in and that are subject to the Apple Public Source License Version 2.0 (the ‘License’). You may not use this file except in compliance with the License. Please obtain a copy of the License at http://www.opensource.apple.com/apsl/ and read it before using this file. - Page 101 SC-F7000 Series User’s Guide Software License Terms Altered versions--including, but not limited to, ports to new operating systems, existing ports with new graphical interfaces, versions with modified or added functionality, and dynamic, shared, or static library versions not from Info-ZIP--must be plainly marked as such and must not be misrepresented as being the original source or, if binaries, compiled from the original source.
Need help?
Do you have a question about the SureColor SC-F7000 and is the answer not in the manual?
Questions and answers