Page 1
SC-F7200 Series Rev.A SETUP MANUAL SC-F7200 Series SE Group Confidential (Related Staff Only)
Page 2
SC-F7200 Series Rev.A IMPORTANCE • Please inform the user of the next page certainly! • Please print and pass the next page to user and encourage the points of caution.
Page 3
SC‐F‐Series SC-F7200 Series Rev.A Ink refill ■ Check ink levels Replace chip unit with new one attached When this message appears, new ink pack. check ink level of the tank Ink level is more than 70mm: which is indicated by Recommends to continue using the printer until the ink level reaches 70mm from the bottom.
SC-F7200 Series Rev.A About This Manual The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Symbols Used in this Manual C A U T I O N...
SC-F7200 Series Rev.A Revision Status Revision Date of Issue Description June 26,2015 Temporary release for unit July 22,2015 First release for MP unit...
Page 6
SC-F7200 Series Rev.A 1.1 Caution for Installation Installation Serviceman must set it (Not User) 1.2 Choosing a Place for the Printer Instructions for Placing the Printer • keep adequate room as shown. • Choose a level and stable location that can support the weight of the printer (about 288 kg).
Page 7
SC-F7200 Series Rev.A 1.4 Inside of carton box Printer Media Feeding Unit, Auto Take-up Reel Unit Epson Genuine Ink Supply System & Cover...
SC-F7200 Series Rev.A 2. Setup Flow Assemble according to the following flow charts. Service Customer engineer Stand Printer Installation Media Feeding Unit Auto Take-up Reel Unit Ink Supply System Ink Supply System Cover Media Guide Bar Connecting the Power Cable...
Page 9
SC-F7200 Series Rev.A <<Stand>> C H E C K It is recommended to assemble the stand by 3persons. P O I N T Remove the tapes. Insert the strut into the stands with supporting the stands. Tighten 4screws...
Page 10
SC-F7200 Series Rev.A Check the markings of L & R on both stands and strut. Tighten 4screws with supporting the stands. Tighten 1screw Tighten 2screws...
Page 11
SC-F7200 Series Rev.A <<Printer>> Take out the Carrying Bar Insert the Carrying Bar Set the carrying bar for printer to be between two screws the carrying bar, locate the screws upside.
Page 12
SC-F7200 Series Rev.A Confirm the stand to be fixed. • Before moving the printer, be sure the stand is fixed in place. C A U T I O N • Be sure the casters are floating on floor. Lift the printer on the stand •...
SC-F7200 Series Rev.A Tighten 3screws with washer Peel tapes off as below. Open the front cover. C A U T I O N Be careful not to trap your hands or fingers when opening or closing the front cover. Pressing the tabs on both sides of the media holding plates to center as shown.
Page 14
SC-F7200 Series Rev.A Remove 2screws, and remove the plate below C H E C K P O I N T Dispose 2screws and this plate. plate...
Page 15
SC-F7200 Series Rev.A <<Media Feeding Unit>> Fix the parts at both sides by tightening screws (total: 4pcs). Rear side Set the Media Feeding Unit firstly from the left side as below. C A U T I O N Carry the Media Feeding Unit (approx. 34.3 kg) using 2persons,...
Page 16
SC-F7200 Series Rev.A Slide core holder and tighten 5screws. Tighten 4screws temporarily until parallel adjustment is completed. C A U T I O N Temporarily tighten (Only home side) Set cable by clamps...
Page 17
SC-F7200 Series Rev.A Open the cover Plug the connector. Set the cable by clamps. Close the cover...
Page 18
SC-F7200 Series Rev.A <<Auto Take-up Reel Unit>> Tighten each 2screws (total: 4pcs) Set Reel Unit...
Page 19
SC-F7200 Series Rev.A Slide core holder and tighten 5screws Tighten 4screws temporarily until parallel adjustment is completed. C A U T I O N Temporarily tighten (Only home side) Set the cable through the bottom clamp behind the printer. Plug the connector, fix it by 2screws.
Page 20
SC-F7200 Series Rev.A 2.7 Stand / Ink Tank / Waste Ink Tube / Waste Tank • Silver ones : 2pcs • Blue ones : 2pcs You can use both Blue ones below. After 100units, This screws will be changed (Running change)
Page 21
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (1) Full and Front side (1pcs) 1. Make sure 2 holes are bigger. 2. Tighten 2 screws temporarily. I x 2 Temporarily tighten 3. Slide the plate & tighten 2 screws.
Page 22
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (2) Full and Rear side (2pcs) 1. Make sure “left parts” and “right parts”. 2. Tighten 2 screws temporarily to keep 1 ~ 2 mm distance. Left parts Right Parts I x 2...
Page 23
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (2) Full and Rear side (2pcs) 3. Slide the plate and tighten 2 screws temporarily. 4. Tighten 4 screws. I x 2 Temporarily tighten Tighten 4 screws...
Page 24
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (2) Full and Rear side (2pcs) 1. Make sure “left parts” and “right parts”. 2. Tighten 2 screws temporarily to keep 1 ~ 2 mm distance. Left parts Right Parts I x 2...
Page 25
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (2) Full and Rear side (2pcs) 3. Slide the plate and tighten 2 screws temporarily. 4. Tighten 4 screws. Temporarily tighten I x 2 Tighten 4 screws...
Page 26
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (3) Home and Rear side (2pcs) 1. As the same as (3) Full and Rear side (2pcs) 2. Tighten total 8 screws. Right Parts Left parts I x 8...
Page 27
SC-F7200 Series Rev.A <<Media Guide Bar(Only 2 flames for left and right)>> Tighten 2 screws temporarily Temporarily tighten Position the part on the stand, and slide it to left. Tighten 2screws. Slide it to left Tighten...
Page 28
SC-F7200 Series Rev.A 1. Hook the plate and Tighten 1 screw temporarily. Temporarily tighten G x 1 2. Align the plate on the L-shape spacer. 3. Tighten 2 screws temporarily. L-shape spacer Temporarily tighten E x 2...
Page 29
SC-F7200 Series Rev.A 4. Tighten 1 more screw temporarily. 5. Set 1 more plate and slide to left. 6. Tighten 1 more screw temporarily. I x 1 Temporarily tighten It was already assembled at factory. I x 1 Temporarily tighten...
Page 30
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (4) Home and Front side (1pcs) 1. Make sure 2 holes are smaller 2. Tighten 2 screws temporarily and slide the plate to fix onto the stand. 3. Tighten 2 more screws on front side temporarily.
Page 31
SC-F7200 Series Rev.A Attach 6pcs plates for strengthen stand (4) Home and Front side (1pcs) 4. Tighten 1 more screws temporarily. D x 1 Temporarily tighten 5. Tighten all temporarily tightened screws. (Total : 10 pcs) <<From page28 to page30>>...
Page 32
SC-F7200 Series Rev.A 1. Pass the tube and Hook the plate to fix as below. (2 hooks) 2. Tighten 5 screws. Bottom Side of Left Side of G x 5 The plate The plate...
Page 33
SC-F7200 Series Rev.A 1. Loosen 2 screws and make sure Front Plate is low. Loosen Front Plate 2. Loosen 4 screws and Make sure the plates to be able to move up/low and left/right.. Loosen Loosen Loosen Loosen...
Page 34
SC-F7200 Series Rev.A 1. Tighten 2 long screws temporarily. Not to touch Temporarily tighten Temporarily tighten...
Page 35
SC-F7200 Series Rev.A 1. Make sure the color index on the plate. 2. Put each CSIC on each slider. 3. Set only Cyan and Black Ink Tanks into Ink Holder as the same order as the color index. ****Set the tank...
Page 36
SC-F7200 Series Rev.A Set to fit between cut position of Ink Tank and hook of Ink Holder. Please do NOT be down all levers before adjustment tank height. IMPORTANCE OK!! NG!! Set Ink Tank again Tighten 2 Blue screws temporarily.
Page 37
SC-F7200 Series Rev.A 1. Raise the plate softly and Tighten 2 screws. 2. Insert 2 pcs thickness-gauges(2.0mm) with raising the tanks at 2 locations(Black and Cyan). 3. Tighten 2 Blue screws to fix the tanks(only Black&Cyan). Tighten Tighten Tighten To fix the tank...
Page 38
SC-F7200 Series Rev.A << Rough Height Adjustment>> 1. Tighten Right Long Screw until the 2pcs thickness(2.0mm) gauges can be moved smoothly at 2 locations(Black and Cyan). 2. Tighten Left Long Screw as the same as the right one. 3. Loosen 2 Blue screws.
Page 39
SC-F7200 Series Rev.A << Detail Height Adjustment>> 1. Tighten Right Long Screw until the 2pcs thickness gauges(2.0mm) can be moved smoothly, AGAIN at 2 locations(Black and Cyan). 2. Tighten Left Long Screw as the same as the right one. 3. Make sure the thickness gauge(2.5mm) can’t be passed...
Page 40
SC-F7200 Series Rev.A 1. Set the other tanks(Yellow and Magenta). 2. Tighten 4 screws to fix the tanks.. (Yellow => Magenta => Cyan => Black) H x 2 Tighten to fix Tighten to fix Yellow 2. Magenta Tighten to fix...
Page 41
SC-F7200 Series Rev.A 1. Make sure thickness-gauge(2.0mm) can be passed and thickness-gauge(2.5mm) can’t be passed Again at 2 locations(Black and Cyan). 2.0mm => Can be Passed 2.5mm => Can’t be Passed...
Page 42
SC-F7200 Series Rev.A Check the vertical position of Ink Tank. If it is enough to hold/insert the Ink Tank, please set C A U T I O N this Ink Tank again. OK!! NG!! Set Ink Tank again Check the front and rear position of Ink Tank.
Page 43
SC-F7200 Series Rev.A 1. Tighten 2 screws. 2. Push 4 tanks softly by hand. 3. Tighten 2 more screws without pushing by hand. Tighten Tighten Tighten Tighten...
Page 44
SC-F7200 Series Rev.A 1. Loosen 2 screws, again. 2. Tighten 2 screws with rising the plate softly. 3. Lock down all levers. Loosen Loosen Tighten Tighten...
Page 45
SC-F7200 Series Rev.A 1. Turn back the tank guard plate and hook the plate into the holes of tank guard plate. (2 hooks) 2. Tighten 4 screws. Tank guard plate 2 hooks (Top side) Tighten 2 holes Tank guard plate...
Page 46
SC-F7200 Series Rev.A 1. Hook the plate into the holes of fix. 2. Tighten 9 screws. 2 hooks Tighten J x 9...
Page 47
SC-F7200 Series Rev.A Peel off the tapes on the tube and pass through the tube into the hole. Unlock the 2clamps...
Page 48
SC-F7200 Series Rev.A 1. Cover the plate over Waste Ink Tube. 2. Make sure the hook is under Upper Clamp and lock it. 3. Make sure the hook is above Lower Clamp and lock it. Plate Upper Clamp Upper Clamp...
Page 49
SC-F7200 Series Rev.A Fix Waste ink Joint of the tube onto the plate as below. Waste ink joint...
Page 50
SC-F7200 Series Rev.A Set Stopper as below. Stopper 2 hooks C H E C K The lid of the Waste Ink Bottle is required when disposing P O I N T of the waste ink. Keep the lid. Do throw it away.
Page 51
SC-F7200 Series Rev.A Stick the label for your territory on the English label if necessary...
Page 52
SC-F7200 Series Rev.A Hold the Media guide bar in both hand, tighten 2screws The media guide bar is heavy. A minimum of 2persons is C A U T I O N required for assembly. Tighten E x 2 Tighten 2screws...
Page 53
SC-F7200 Series Rev.A <<Parallel Adjustment of the Media Feeding Unit>> C H E C K When the film will be reused, the adhesive side may be P O I N T soiled. Soak a lint-free cloth in water, wring it out, and then use it to wipe away the dust and lint stuck to the reverse side.
Page 54
SC-F7200 Series Rev.A <<Media Feeding Unit>> Pass 2films from Rear side Release after checking “L”, “R”. Open Remove protective sheet, and put it after aligned screws Loosen 4screws...
Page 55
SC-F7200 Series Rev.A Remove protective sheet, Loosen knobs, and put it after aligned (2) and and fix knobs after aligned (4) screws Frame of Board box Frame of Board box Loosen knobs, and slide it...
Page 56
SC-F7200 Series Rev.A Turn counter clockwise Turn clockwise until No visible “A” Pass film into Core Pass film from Rear Set Core Align a film to b film (Rear and Front side)
Page 57
SC-F7200 Series Rev.A Attach Counterweight, and Move film to Home side, and Measure and note value Check value -> Same = No need to adjust ->different = Need to adjust...
Page 58
SC-F7200 Series Rev.A Remove counterweight Adjustment to turn screw Loosen knob, and slide it, Pull film Tighten 4screws after adjust same value Remove core (with film)
Page 59
SC-F7200 Series Rev.A <<Auto take-up Reel Unit>> Loosen 4screws Loosen knobs, and fix knobs after aligned Frame of after heater Turn counter clockwise Frame of After heater...
Page 60
SC-F7200 Series Rev.A Set Core Pass film from Front To through Media Guide Bar Turn clockwise until No visible “A” IMPORTANCE After Heater Paper Media Guide Bar Roll Core...
Page 61
SC-F7200 Series Rev.A Move film to Home side, and Align a film to b film Check value (Rear and Front side) -> Same = No need to adjust Attach Counterweight, and ->different = Need to adjust Measure and note value...
Page 62
SC-F7200 Series Rev.A Adjustment to turn screw Remove counterweight Remove core (with film) Tighten 4screws after adjust same value...
Page 63
SC-F7200 Series Rev.A Pass film from Front Align a film to b film To use Media Guide Bar (Rear and Front side) Attach Counterweight, and Measure and note value IMPORTANCE After Heater Paper Media Guide Bar Roll Core cofidencial...
Page 64
SC-F7200 Series Rev.A Move film to Home side, and Loosen 2screws Check value to use small hexagon wrench -> Same = No need to adjust ->different = Need to adjust...
Page 65
SC-F7200 Series Rev.A Adjustment to turn screw Remove counterweight Remove core (with film) Tighten 2screws after adjust same value...
Page 66
SC-F7200 Series Rev.A <<Connecting the Power Cable>> • Use only the type of power source indicated on the C A U T I O N printer’s label. Install the clamp Connecting 2 power cables at Printer Fasten the cables by 2clamps.
Page 67
SC-F7200 Series Rev.A 2.11 Fill the ink C A U T I O N Wear security goggle and globes, wash your skin immediately when the ink adheres to your skin. C A U T I O N Shake the ink packs of all colors well to prevent the ink settlement.
Page 68
SC-F7200 Series Rev.A Fill the ink. C A U T I O N • Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink tanks.
SC-F7200 Series Rev.A 2.12 Firmware update Turn ON the printer in the F/W update mode. Push “ON” while pressing [Media setup] + [Media feed] +[Maintenance]. PUSH IMPORTANCE Check the current Firmware version. Update the latest FW. Printer will be turned off automatically.
Page 70
SC-F7200 Series Rev.A Turn ON the printer in the Normal mode. Set the printer setting. (Language, date, time etc.) Starting Ink Charge. ( Approximately 50 min) Check the nozzle check pattern. If nozzle missing, do cleaning.
Page 71
SC-F7200 Series Rev.A *** If necessary *** <<Check the Ink Tank position>> 1. Turn ON the printer in the Serviceman Mode. Push “ON” while pressing [Menu] + [Back] + [OK]. IMPORTANCE 2. [SELF TESTING] -> [Mech Adjustment] ->[Sensor Check] -> [ILS] 3.
Page 72
SC-F7200 Series Rev.A Trouble shooting for ink charge 1. Check the Ink Tank condition according to the following tables. 2. If it is enough to set the Ink Tank, please set this Ink Tank again. Trouble Cause Hook of Ink Tank comes off •...
Need help?
Do you have a question about the SC-F7200 Series and is the answer not in the manual?
Questions and answers