Page 1: Users Manual
CLM R10+ Users manual R9050100 R90501001 R90501005 R59770021/11 11/10/2010...
Page 2 Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.88.24 E-mail: sales.events@barco.com Visit us at the web: www.barco.com Printed in Belgium...
Page 3: Software License Agreement
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justiﬁed notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
Page 4: Disposal Information
GNU-GPL code If you would like a copy of the GPL source code contained in this product shipped to you on CD, please contact Barco. The cost of preparing and mailing a CD will be charged.
Page 5: Table Of Contents
Table of contents TABLE OF CONTENTS 1. Safety ....................... .. 5 General .
Page 6 Table of contents 8. Input menu ......................63 Overview ﬂow .
Page 7 Table of contents 12.4 Side keystone........................120 12.5 Blanking.
Page 8 Table of contents 16.7 Removal of an input module ..................... . .176 16.8 Inserting an input module .
Page 9: Safety
• Before operating this equipment please read this manual thoroughly, and retain it for future reference. • Installation and preliminary adjustments should be performed by qualiﬁed Barco personnel or by authorized Barco service deal- ers. • All warnings on the projector and in the documentation manuals should be adhered to.
Page 10: Important Safety Instructions
Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualiﬁed service personnel. The customer should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to Barco. •...
Page 11 ﬂammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all Barco DLP projectors. The exclusion zone on the lens side must be at least 2 meter (80”).
Page 12: Recycling Guidelines
If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu- tions may result in degraded performance and reliability, ﬁre, electric shock or other hazards.
Page 13: Important Warnings Concerning Clm Flight Cases
1. Safety Important warnings concerning CLM ﬂight cases Important warnings concerning stacking/transporting CLM rental ﬂight cases • Stack maximum two (2) CLM rental ﬂight cases high. Never higher. • Surface on which ﬂight case is standing must be level to ensure that the total load is evenly spread out among the four wheels. The surface must also be able to support the load safely.
Page 14 1. Safety R59770021 CLM R10+ 11/10/2010...
Page 15: General
Projector weight Do not underestimate the weight of one Barco CLM R10+, which is about ±31 kg (±68 lb.). Be sure that the table or truss installation on which the projector(s) has to be installed is capable of handling ﬁve (5) times the complete load of the complete system.
Page 16: Unpacking The Projector
2. General Which screen type ? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reﬂect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them.
Page 17: Box Content
This check should conﬁrm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel are not scratched of cracked. The Barco sales and service ofﬁce should be notiﬁed as soon as possible.
Page 18: Projector Conﬁgurations
2. General Projector conﬁgurations The different conﬁgurations Depending on the installation the projector can be mounted in different ways, the 4 different conﬁgurations are: Front / Table (F/T) Front / Ceiling (F/C) Rear / Table (R/T) Rear / Ceiling (R/C) For a ceiling mounted conﬁguration, the optional carry handle kit is required.
Page 19: Positioning The Projector
2. General Positioning the projector SCREEN FLOOR Image 2-5 On-Axis / Off-Axis projection The position of the projector with reference to the screen may also be different depending on the installation. Basically the projector can be positioned in On-Axis or Off-Axis conﬁguration. On-Axis conﬁguration means that the projector is positioned so as to have the centre of the lens coinciding with the centre of the screen.
Page 20 2. General +110% SIDE VIEW +110% -29% -103% +17.5% -103% TOP VIEW -29% +17.5% Image 2-6 Shift range Field of view It’s mechanical possible to shift outside the recommended ﬁeld of view (±100% UP/DOWN and ±70% LEFT/RIGHT), but this will result in a slightly decline of image quality depending on the used lens and the zoom position of the used lens.
Page 21: Projector Air Inlets And Outlets
Projector Toolset is only available in a download version, no CD can be ordered. Where to ﬁnd the download ﬁle(s) The program and all necessary plug-ins, as well as the Reference manual can be downloaded for free from Barco’s Partnerzone, URLhttps:\\my.barco.com. Registration is necessary.
Page 22 2. General R59770021 CLM R10+ 11/10/2010...
Page 23: Physical Installation
3. Physical installation 3. PHYSICAL INSTALLATION About this chapter This chapter explains how to install and set up your CLM projector. If you are familiar with the projector and want to quickly set it up for temporary use, follow the “Quick setup” instructions below. For a more complete setup, follow the instructions and guides covered in the remaining subsections.
Page 24: Rcu Battery Installation
3. Physical installation Overview • RCU battery installation • RCU rugged case installation • RCU XLR adaptor installation • Using the XLR adaptor of the RCU • RCU usage possibilities 3.1.1 RCU battery installation Where to ﬁnd the batteries for the remote control ? The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time.
Page 25: Rcu Rugged Case Installation
3. Physical installation 3.1.2 RCU rugged case installation Only with optional rugged case kit which is part of the touring kit (R9861000). Necessary tools No tools. Necessary parts Touring kit How to install the rugged case of the remote control ? 1.
Page 26: Using The Xlr Adaptor Of The Rcu
3. Physical installation Image 3-6 Mounting the XLR adapter 3.1.4 Using the XLR adaptor of the RCU How to use the XLR adaptor of the remote control unit ? 1. Connect a cable with XLR plug into the XLR adaptor. 2.
Page 27: Lenses
3. Physical installation Image 3-8 Lenses Overview • Available lenses • Lens selection • Lens formulas • Lens formulas 3.2.1 Available lenses Overview First series lenses: Image 3-9 Image 3-10 Image 3-11 R9849870: CLD zoom lens (1.2 - 1.6 : 1) R9861100: CLD zoom lens (1.6 - 2.4 : 1) R9849890: CLD zoom lens (2.4–4.3 : 1) Second generation lenses :...
Page 28: Lens Selection
3. Physical installation Image 3-12 Image 3-13 Image 3-14 R9861060: CLD zoom lens (1.2–1.5 : 1) R9861070: CLD zoom lens (1.5–2.2 : 1) R9861071: R9861080: CLD zoom lens (2.2–4.4 : 1) CLD zoom lens (1.5–2.2 : 1 ) HD Image 3-15 R98610890: CLD zoom lens (4.4–7.0 : 1) Lens Order number...
Page 29: Lens Formulas
3. Physical installation Image 3-16 PD for lens selection 3.2.3 Lens formulas Formulas Lens Throw ratio for Metric formulas (meter) Inch formulas (inch) CLD (1.2 - 1.6 : 1) 1.2 - 1.6 =1.216 x SW - 0.05 =1.216 x SW - 1.97 =1.657 x SW - 0.097 =1.657 x SW - 3.80 CLD (1.6 - 2.4 : 1)
Page 30: Alignment Of A Table Mounted Clm Projector
3. Physical installation Alignment of a table mounted CLM projector How to align a table mounted CLM projector 1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen. 2.
Page 31 3. Physical installation Image 3-19 Rigging slots and clamps Necessary tools Open end spanner 17 mm Necessary parts • Four rigging clamps (R855943) • Safety cable (B361213) • Two snap hook locks (B361212) Mounting the rigging points into the handle 1.
Page 32 3. Physical installation Image 3-20 Mount rigging points X mm Image 3-21 x mm Image 3-22 Set up truss width R59770021 CLM R10+ 11/10/2010...
Page 33 3. Physical installation Image 3-23 Mounting rigging clamps Image 3-24 Opening clamps R59770021 CLM R10+ 11/10/2010...
Page 34: Alignment Of A Ceiling Mounted Clm Projector
3. Physical installation Image 3-25 Mounting to truss Image 3-26 Security cable AUTION Always mount the safety cable when suspending the projector. Alignment of a ceiling mounted CLM projector Necessary tools Spanner 17 mm R59770021 CLM R10+ 11/10/2010...
Page 35 3. Physical installation How to align a ceiling mounted CLM projector 1. Install the projector in the desired location. See "Suspension of the CLM projector with rigging clamps", page 26. Take into account the zoom range of the used lens and the size of the screen. 2.
Page 36 3. Physical installation R59770021 CLM R10+ 11/10/2010...
Page 37: Stacking Clm Projectors
4. Stacking CLM projectors 4. STACKING CLM PROJECTORS Stacking of CLM projectors is only possible with optional touring kit. See "Mounting optional Carry handle", page 209 for more information. Overview • Stacking CLM projectors • Aligning stacked CLM projectors Stacking CLM projectors Preparations Install ﬁrst a carry handle on the upper projector.
Page 38 4. Stacking CLM projectors Image 4-2 Close the interlocking Image 4-3 Ceiling mounted stacked projectors How to open an interlocking adapter 1. Open an interlocking adapter as illustrated. (image 4-4) R59770021 CLM R10+ 11/10/2010...
Page 39: Aligning Stacked Clm Projectors
4. Stacking CLM projectors Image 4-4 Open the interlocking ARNING Never open an interlocking adapter of a stacked projector which is still suspended. First place the stacked projectors on the ﬂoor. Aligning stacked CLM projectors How to align two stacked CLM projectors 1.
Page 40 4. Stacking CLM projectors Image 4-5 Rotation adjustment Inclination Image 4-6 Inclination adjustment Skew Image 4-7 Skew adjustment Shift Image 4-8 Shift adjustment R59770021 CLM R10+ 11/10/2010...
Page 41 4. Stacking CLM projectors Zoom Image 4-9 Zoom adjustment R59770021 CLM R10+ 11/10/2010...
Page 42 4. Stacking CLM projectors R59770021 CLM R10+ 11/10/2010...
Page 43: Connections
5. Connections 5. CONNECTIONS About this chapter This chapter describes more in detail the power (P), the input source (S) and the communication (C) connections of the CLM R10+. Image 5-1 Overview • Power connection • Input source connections • Communication connections Power connection AUTION...
Page 44 5. Connections Image 5-2 Power input ARNING Do not attempt operation if the AC supply and cord are not within the speciﬁed voltage and power range. AUTION Once the projector is switched to standby, the lamp cooling fans will continue to run for approx- imately ﬁve minutes to ensure that the projector and lamp have sufﬁciently cooled, at which point the fans will automatically decrease to standby.
Page 45: Input Source Connections
5. Connections Power input voltage versus light output (for R90501005) Input power between 100V and 264V, the maximum light output with 4 lamps can be reached. Input power between 90V and 99V, 83% of the light output with 4 lamps. Input source connections General The input and communication unit is equipped with two input slots, which accept any type of input designed for the CLM projector.
Page 46: Communication Connections
5. Connections The CLM R10+ is standard equipped with one 5 cable input module and one DVI input module. Communication connections Communication interface DIAGNOSTIC CODE IR RECEIVER STBY / ON WARNING IR 10/100 10/100 REMOTE BASE-T CTRL RS232 / 422 OUT RS232 / 422 IN Image 5-10 Communication connections...
Page 47: Wired Remote Control
5. Connections IR communication (RC5) An IR receiver (L) is mounted on the communication interface. Note that there is also an IR receiver mounted at the front and at the back of the projector. When using the remote control unit (wired or wireless), the “IR REC” (D) and the “IR OK” (C) LED’s will light up indicating an IR signal was received and recognized.
Page 48: Usb Port
5. Connections Image 5-11 Pin numbering male DB–9 connector. Pin numbering female DB-9 connector. RS232 An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the commu- nication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines.
Page 49 5. Connections DMX is used as communication bus between different devices in the light technic. Each device has an input and an output, so that the bus can be looped between the different devices. According the standard a ﬁve wire cable with XLR connector is used but mostly 3-wire cables are used.
Page 50 5. Connections R59770021 CLM R10+ 11/10/2010...
Page 51: Getting Started
6. Getting started 6. GETTING STARTED About this chapter This chapter describes the functions on the remote control and local keypad and gives an overview how to start up the projector. It gives also a brief overview of the direct adjustment possible with these controls. Overview •...
Page 52 6. Getting started MENU EXIT ENT ER PAUSE LENS TEXT EXIT MENU PHASE SHARP N PATTERN WINDOW LENS TINT ENTER RIGGING STBY PAUSE TEXT AUTO COLOR BRI GHTN CONTR LENS LENS ZOOM SHIFT LENS LENS SHIFT FOCUS Image 6-1 Local keypad & remote control Ind.
Page 53: Operating The Projector
6. Getting started Ind. Key name Description PHASE Used to remove the horizontal instability of the image (usually for RGB source). It adjusts the phase of the pixel sampling clock relative to the incoming signal. FREEZ To freeze the actual projected image. Freeze sign is displayed in the upper left corner (a short press on the key).
Page 54: Errors, Warnings And Messages During Start Up
6. Getting started Starting image projection via the standby key. 1. Press Stand by key once on the local keypad or on the remote control. (image 6-3) The projector status LED lights up. The projector starts up on the last saved source. Some lamp and runtime warnings can be displayed when an image is displayed after a start up.
Page 55: Switching Off
6. Getting started Switching to Standby. When the projector is running and you want to go to standby, press the standby key for 2 seconds. Do not press any longer on the standby key otherwise the projector will restart. All custom settings are written to the internal backup device. A message ’Save data ...’ indicates this process. Never switch off the projector while this message is displayed.
Page 56: Quick Setup Adjustments
6. Getting started 45° 45° 45° 45° 45° 45° Image 6-5 RCU to one of the IR sensors Quick setup adjustments Overview • Text boxes ON or OFF • Quick Lens Adjustment • Quick picture in picture • Quick layout selection with Rigging key •...
Page 57: Direct Lens Adjustment (Rcu)
6. Getting started Image 6-6 Press the LENS key to switch to another pattern. Different patterns are available. Quick shift adjustment 1. Press the LENS key on the remote control or local keypad. The zoom/focus menu will be displayed. (image 6-7) 2.
Page 58: Quick Picture In Picture
6. Getting started Zoom Vertical shift Focus Horizontal shift 6.5.3 Quick picture in picture Quick On - Off Press on the PIP key on the remote control or the local keypad to activate the Load layout window. Use the ▲ ▼ key to scroll to the desired layout and press ENTER to activate. Select Main full screen to switch off PIP.
Page 59: Quick Language Selection
6. Getting started When no digit is pressed after Rigging is pressed, the layout selection menu disappears after a few seconds without a layout change. 6.5.5 Quick language selection Language selection 1. Press Menu to activate the menus and select with the ▲ or ▼ key Projector Control and press ENTER. 2.
Page 60: Controlling The Projector
6. Getting started Image 6-16 To continue using the RCU with that speciﬁc address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press "3"...
Page 61: Source Selection
6. Getting started Source selection Source selection when no picture in picture is active Use the digit keys on the remote control or local keypad to active the desired source. Source selection when picture in picture is active Use the Window button on the remote control or the local keypad to select the main window or the picture in picture (PiP) window. EXIT MENU PATTERN...
Page 62: The Pause Key
6. Getting started Sharpness The sharpness function is used to adjust the image sharpness of video signals. Use the + button for more sharpness Use the - button for less sharpness Phase Use the + or - side of the phase control button to adjust the phase. The Pause Key When the Pause key is pressed, the image projection is stopped, a black screen will be displayed and the projector remains with full power for immediate restart.
Page 63: Start Up Of The Adjustment Mode
7. Start up of the Adjustment mode 7. START UP OF THE ADJUSTMENT MODE Overview • About the adjustment mode • About the use of the remote control and the local keypad • Start up the adjustment mode • Navigation and adjustments •...
Page 64: Navigation And Adjustments
7. Start up of the Adjustment mode Image 7-1 Navigation and adjustments How to navigate in the menu structure? Once in the menu structure, use the ▲ or ▼ keys on the remote control (or the ▲ or ▼ (+ or -) key on the local keypad) to scroll through the items in the displayed menu.
Page 65: Test Patterns In Adjustment Mode
7. Start up of the Adjustment mode Test patterns in adjustment mode Overview When the adjustment mode is started, a test pattern can be called at any moment just by pressing the Pattern key on the RCU or the local key path. Press as many times on the Pattern key as necessary to display the desired test pattern. The test pattern remains on the screen as long as the adjustment mode is selected, even when selecting other menus.
Page 66 7. Start up of the Adjustment mode R59770021 CLM R10+ 11/10/2010...
Page 67: Input Menu
8. Input menu 8. INPUT MENU Overview • Overview ﬂow • Slot module type • Input locking • Minimum delay • Native resolution • Source switching • No signal Overview ﬂow Overview Level 1 Level 2 Level 3 Input 5-cable Slot module type HD-SDI - SDI DVI HDCP...
Page 68: Input Conﬁguration
8. Input menu AUTION Always install a cover plate on an unused input slot. This to prevent dust intrusion into the pro- jector. 8.2.2 Input conﬁguration How to change? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Input and press ENTER. The Input menu is displayed.
Page 69: Input Locking
8. Input menu Input Indication Description module RGB SOG RGB input with sync on green YUV HS/VS - CS Component video with separate horizontal and vertical sync or separate composite sync. YUV CV Component video with composite video as sync signal YUV SOY Component video with sync on Y CVBS...
Page 70 8. Input menu When: Free run Output is locked on an internal sync (60 Hz) Automatic Output is locked on the selected input for the main window Input 1 Output is locked on source 1 Input 2 Output is locked on source 2 The options menu changes depending on the selection.
Page 71: Minimum Delay
8. Input menu Genlock off (default position) locking done on input source of main window, when automatic was selected or on the selected input source when a speciﬁc input was selected. Projector detects automatically the vertical frequency and clock frequency of the input signal. A slightly difference with the source is possible. Genlock on locking done on indicated vertical frequency and clock frequency.
Page 72 8. Input menu Image 8-13 When the show native resolution function is in the ON position, the projector handles the source as follows: Source Projected image Name Ratio Resolution Ratio Resolution 1024x768 1024x768 image projected with black borders SXGA 1280x1024 1280x1024 image projected with black borders...
Page 73: Source Switching
8. Input menu Source switching Switching from one source to another To minimize undesired effects when switching from one source to another one can use the switching mode, using the fade effect. Image 8-16 Example of fade effect Switching mode set up 1.
Page 74: Shutdown Setting
8. Input menu The Input menu is displayed. 3. Use the ▲ or ▼ key to select No signal and press ENTER to toggle between [Black] and [Blue]. (image 8-20, image 8-21, image 8-22) Image 8-22 Image 8-21 Image 8-20 8.7.2 Shutdown setting How to change the shutdown setting...
Page 75 8. Input menu Image 8-28 Image 8-27 Image 8-26 R59770021 CLM R10+ 11/10/2010...
Page 76 8. Input menu R59770021 CLM R10+ 11/10/2010...
Page 77: Image Menu
9. Image menu 9. IMAGE MENU Overview • Overview ﬂow • How to select the image adjustments? • Image Settings • Aspect ratio • Timings • Image ﬁles services • Save custom settings Overview ﬂow Overview Level 1 Level 2 Level 3 Level 4 Image...
Page 78: How To Select The Image Adjustments
9. Image menu Level 1 Level 2 Level 3 Level 4 Vertical start Advanced settings Clamp delay Clamp width Field polarity Film mode detection Image ﬁle services Manual load Delete Delete all Rename Copy Options Load ﬁle Save custom settings How to select the image adjustments? Start up 1.
Page 79: Contrast
9. Image menu 9.3.1 Contrast About Contrast The contrast function is used to adjust the contrast between the light and dark areas of the displayed image. How to change the contrast? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3.
Page 80: Saturation
9. Image menu Image 9-8 Image 9-7 Image 9-9 Image 9-10 9.3.3 Saturation About (color) saturation The color function is used to adjust the color saturation levels. How to change the saturation? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3.
Page 81: Tint (Hue)
9. Image menu 9.3.4 Tint (hue) About Tint The Tint function is used to adjust color hue to obtain true color reproduction and is only active for Video and S-Video when the NTSC color system is used. For PAL and SECAM sources, Tint is not accessible. How to change the saturation? 1.
Page 82: Sharpness
9. Image menu 2. Use the ▲ or ▼ key to select Image and press ENTER. 3. Use the ▲ or ▼ key to select Image settings and press ENTER. 4. Use the ▲ or ▼ key to select Phase and press ENTER. The Phase progress bar appears.
Page 83: Noise Reduction
9. Image menu Image 9-27 9.3.7 Noise reduction About Noise reduction Reduces noise and pixel jitter in all video sources. How to change? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3.
Page 84: Predeﬁned Color Temperature
9. Image menu Color temperature selection is only possible when Color space is OFF Color temperature The coloration (reddish, white, bluish, greenish, etc.) of white in an image, measured using the Kelvin (degrees K) temperature scale. Higher temperatures output more light. 9.3.8.1 Predeﬁned color temperature Projector white will provide maximum projector light output.
Page 85: Input Balance
9. Image menu 3. Use the ▲ or ▼ key to select Image settings and press ENTER. 4. Use the ▲ or ▼ key to select Color temperature and press ENTER. 5. Use the ▲ or ▼ key to select Custom balance and press ►. The Gain adjustment bar scales are displayed.
Page 86 9. Image menu 0.7V Black level Image 9-41 Δ G ΔΒ Δ R Black level Image 9-42 One can conclude here that a good color tracking can only be met by using three previously (input) balanced color signals Analog Digital Conversion The analog color signals must pass through an Analog/Digital conversion circuit prior to any digital processing in the PMP.
Page 87: Adjusting The Input Balance
9. Image menu 9.3.9.2 Adjusting the input balance How can it be done ? To balance the three color signals of a particular source there are conditions; in fact we must know the black and the white level of the source i.e. : The source in question must be able to generate a white signal, ideally a 100% white (background) full screen pattern The source in question must be able to generate a black signal, ideally a 100% black (background) full screen pattern Image 9-44...
Page 88 9. Image menu 9. Toggle with ▲ or ▼ key to Black balance blue and adjust the blue black level on a minimal value. Note: This minimal value is not necessary , provided that the 2 other colors are not inﬂuencing too much the color to be adjusted, in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the 50% transition due to the contribution of these two other colors signals.
Page 89: Aspect Ratio
9. Image menu Image 9-52 Image 9-51 Image 9-53 Image 9-55 Image 9-54 Aspect ratio What can be done? The aspect ratio setting forces the projector to project an image using a deﬁned aspect ratio Aspect ratio Description Standard television format 16:9 Wide screen television format / anamorphic format Workstation format...
Page 90 9. Image menu 16/9 Video Signal Pal/Secam Video Signal NTSC Video Signal 16/9 4/3 RGB Signal Image 9-56 Some examples for aspect ratio How to select an Aspect ratio? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3.
Page 91: Timings
9. Image menu The Custom aspect ratio dialog box opens. 2. Use the ▲ or ▼ key to adjust the vertical size of the image. Use the key to adjust the horizontal size of the image. When the desired aspect ratio is obtained, press EXIT. (image 9-60, image 9-61) Image 9-61 Image 9-60 Timings...
Page 92: Advanced Settings
9. Image menu Image 9-63 Image 9-62 Image 9-64 Image 9-65 9.5.2 Advanced settings About the advanced settings Clamp delay The time between the leading edge of the clamp pulse and the locked edge of the sync pulse. Can be any value between 0 and 255.
Page 93 9. Image menu 5. Use the ▲ or ▼ key to select Clamp delay or Clamp width and press ENTER. A progress bar appears. 6. Use the ▲ or ▼ key to change the setting. (image 9-67, image 9-68, image 9-69, image 9-70) Image 9-68 Image 9-67 Image 9-69...
Page 94: Advanced Settings, Film Mode Detection
9. Image menu Image 9-74 9.5.3 Advanced settings, ﬁlm mode detection About ﬁlm mode detection This mode detects whether ﬁlm or video is displayed. When enabled, the hardware looks for tell-tale signs of 3:2 or 2:2 pull-down sequences. These are the result of converting cinema material recorded at 24 frames-per-second to the television frequencies of 60 or 50 interlaced ﬁelds per second respectively.
Page 95: Advanced Setting, Brilliant Color Look
9. Image menu Image 9-76 Image 9-75 Image 9-77 Image 9-78 9.5.4 Advanced setting, brilliant color look What can be done ? The BrilliantColor™ technology is conﬁgured to process the spoke regions of the color wheel as a secondary color which improves the brightness of the display and gives the viewer a truly life-like image.
Page 96: Image Files Services
9. Image menu Image 9-80 Image 9-79 Image 9-81 Image 9-82 Image ﬁles services Overview • Files and ﬁle manipulations • Manual Load ﬁle • Delete ﬁle • Delete all custom ﬁles • Rename a ﬁle • Copy a ﬁle •...
Page 97: Manual Load File
9. Image menu 9.6.2 Manual Load ﬁle How to load? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3. Use the ▲ or ▼ key to select File services and press ENTER. The File service menu is displayed.
Page 98: Delete All Custom Files
9. Image menu 5. Use the ▲ or ▼ key to select the ﬁle which must be deleted. Note: Only custom ﬁles can be deleted. 6. Press ENTER to delete the selected ﬁle. (image 9-87, image 9-88, image 9-89, image 9-90) Image 9-88 Image 9-89 Image 9-87...
Page 99: Rename A File
9. Image menu Image 9-94 9.6.5 Rename a ﬁle How to rename? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Image and press ENTER. 3. Use the ▲ or ▼ key to select File services and press ENTER. The File service menu is displayed.
Page 100: File Options
9. Image menu 2. Use the ▲ or ▼ key to select Image and press ENTER. 3. Use the ▲ or ▼ key to select File services and press ENTER. The File service menu is displayed. 4. Use the ▲ or ▼ key to select Copy and press ENTER. The copy window opens.
Page 101: Save Custom Settings
9. Image menu Image 9-106 Image 9-107 Image 9-105 Image 9-108 Image 9-109 Save custom settings What is done? The current custom settings can be saved to the internal backup device in the same way as it would be done when the projector was switched to standby.
Page 102 9. Image menu R59770021 CLM R10+ 11/10/2010...
Page 103: Layout Menu
10. Layout menu 10. LAYOUT MENU Overview • Overview ﬂow • Main window • PIP window • Layout ﬁle services 10.1 Overview ﬂow Overview Level 1 Level 2 Level 3 Level 4 Layout Main window Source Size Position PIP window PIP window [ON/OFF] Source Size...
Page 104: Source Selection
10. Layout menu Image 10-2 Image 10-1 The ﬁrst character is highlighted. Use the ▲ or ▼ key to select the desired character and press key to select the next character in the name. Press EXIT to return. The new ﬁle is generated. 10.2.1 Source selection What can be done ? The source of the main window can be selected via the Main window menu.
Page 105 10. Layout menu Image 10-7 Size adjustment main window width adjustment height adjustment The size can be changed with respect to the original aspect ratio. How to adjust with respect to the original aspect ratio? 1. Press MENU to activate the menus. 2.
Page 106: How To Adjust Height And Width Separately
10. Layout menu Image 10-12 Image 10-11 How to adjust height and width separately? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Layout and press ENTER. 3. Use the ▲ or ▼ key to select Main Window and press ENTER. The main window opens.
Page 107: Position Adjustment
10. Layout menu 10.2.3 Position adjustment What can be done? The main window can be repositioned on the screen. The upper left corner is the reference. Image 10-18 Positioning the window How to position? 1. Press MENU to activate the menus. 2.
Page 108: Pip Window
10. Layout menu 10.3 PIP window Overview • Introduction to PIP • Picture in Picture activation • Picture in Picture source selection • Picture in Picture size of the window • Picture in Picture, position window 10.3.1 Introduction to PIP PiP stands for "Picture in Picture"...
Page 109: Picture In Picture Source Selection
10. Layout menu Image 10-26 Image 10-27 Image 10-25 When PIP is activated (ON state), the PIP window becomes the active window. Switching to the main window is still possible with the window button on the RCU. 10.3.3 Picture in Picture source selection What can be done ? The input source for the picture in picture window can be selected.
Page 110: Picture In Picture Size Of The Window
10. Layout menu 10.3.4 Picture in Picture size of the window What can be done? The width and height of the picture in picture window can be changed till the desired dimensions are obtained. Image 10-32 Size PIP window Width PIP window Height PIP window The size of the picture in picture window can be changed with respect to the original aspect ratio of the PIP image.
Page 111: How To Change The Height And Width Separately
10. Layout menu Image 10-35 Image 10-36 Image 10-34 Image 10-38 Image 10-37 How to change the height and width separately? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Window and press ENTER. 3.
Page 112: Picture In Picture, Position Window
10. Layout menu Image 10-43 Image 10-42 10.3.5 Picture in Picture, position window What can be done? The picture in picture window can be position on any place on the display just by changing its start coordinates. The reference is the upper left corner of the window.
Page 113: Layout File Services
10. Layout menu 10.4 Layout ﬁle services Overview • Load layout • Rename a layout • Delete a layout • Copy / Save as a layout 10.4.1 Load layout When loading a layout which required two sources, the PIP window On/Off setting will be switched to ON. How to load? 1.
Page 114: Rename A Layout
10. Layout menu 10.4.2 Rename a layout Only custom created layouts can be renamed. How to rename? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Window and press ENTER. 3. Use the ▲ or ▼ key to select Layout and press ENTER. The layout services window opens.
Page 115: Copy / Save As A Layout
10. Layout menu 4. Use the ▲ or ▼ key to select Delete and press ENTER. The Delete window opens. (image 10-57, image 10-58, image 10-59, image 10-60) The ﬁrst 3 layouts are default layouts and cannot be delete. 5. Use the ▲ or ▼ key to select the layout that must be deleted. 6.
Page 116 10. Layout menu Image 10-63 Image 10-62 Image 10-61 Image 10-64 R59770021 CLM R10+ 11/10/2010...
Page 117: Lamp Menu
11. Lamp menu 11. LAMP MENU Overview • Overview ﬂow • Lamp power mode • Lamp power • Lamp Identiﬁcation • Status and run time overview lamps • Lamp mode 11.1 Overview ﬂow Overview Level 1 Level 2 Level 3 Level 4 Lamp Power...
Page 118: Lamp Power
11. Lamp menu How to switch? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Power and press ENTER. 4. Use the ▲ or ▼ key to select Mode. 5.
Page 119: Lamp Identiﬁcation
11. Lamp menu Image 11-7 About over-temperature protection When the projector software detects a too high lamp temperature it automatically reduce the lamp power with 20%. This reduction will be visible on the Lamp power menu. It is possible to adjust the lamp power again to a higher value but the software will reduce the lamp power again if the temperature is still to high.
Page 120: Status And Run Time Overview Lamps
11. Lamp menu 11.5 Status and run time overview lamps Overview 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Lamp and press ENTER. 3. Use the ▲ or ▼ key to select Overview and press ENTER. The status and the run time for each lamp are displayed.
Page 121: Alignment Menu
12. Alignment menu 12. ALIGNMENT MENU About this chapter This chapter describes the alignment of the projector once the physical installation is ﬁnished. Via the software, the image will be perfectly aligned on the screen. Overview • Overview ﬂow • Orientation •...
Page 122: Orientation
12. Alignment menu Level 1 Level 2 Level 3 Full screen green Full screen red Full screen white Hatch Outline Purity ScenergiX Color space Projector SMPTE Custom White peaking ScenergiX Status White level Bottom Black level Show pattern Reset 12.2 Orientation What can be done? The way of physical installation of the projector can be deﬁned to the projector.
Page 123: Lens Adjustment
12. Alignment menu For more information about the physical installation, see chapter “General”, “Projector conﬁgurations”. 12.3 Lens adjustment Quick way to enter the lens adjustment setting; press the lens button on the local keypad or the remote control. Access to the lens adjustments 1.
Page 124: Side Keystone
12. Alignment menu Image 12-10 Image 12-9 12.4 Side keystone What can be done? The side keystone adjustment is used to align the image if the projector is mounted at a non standard projection angle. Image 12-11 Side keystone Keystone adjustment with positive values Keystone adjustment with negative values Side keystone adjustment 1.
Page 125: Blanking
12. Alignment menu 12.5 Blanking What can be done ? Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A ’0’ on the bar scale indicates no blanking. Which blanking adjustments are available ? •...
Page 126: Intensity
12. Alignment menu Image 12-18 Image 12-16 Image 12-17 12.6 Intensity What can be done The light in the optical light path can be dimmed with a mechanical shutter plate. This way of light dimming will enhance the contrast of the image. Optical light dimming can reduce the light more than the lamp power reduction and it will enhance the contrast at the same time.
Page 127: Internal Pattern
12. Alignment menu 3. Use the ▲ or ▼ key to select Gamma and press ENTER. The Gamma progress bar appears. 4. Use ◄ or ► key to change the gamma setting and press EXIT. Gamma can be set to one of the 8 available steps. (image 12-22, image 12-23, image 12-24) Image 12-24 Image 12-22 Image 12-23...
Page 128: Color Space
12. Alignment menu Image 12-27 Image 12-25 Image 12-26 12.9 Color space Color space A color space or color standard is a mathematical representation for a color. For example the RGB color space is based on a Cartesian coordinate system. What can be adjusted ? The color space (gamut), the collection of colors which can be reproduced by the projector, can be adjusted to 4 predeﬁned stored values (one projector speciﬁc, 2 international standards and one custom preset).
Page 129: White Peaking
12. Alignment menu Image 12-30 Image 12-28 Image 12-29 Image 12-31 When selecting a ﬁxed color space, the values of this selected color space overwrite the custom selected color space. 12.10 White peaking About white peak and brilliant color In video centric applications true color reproduction is generally a priority over brightness. To achieve this a typical design will not utilize a white segment of the color wheel.
Page 130: Scenergix
12. Alignment menu Image 12-34 Image 12-32 Image 12-33 12.11 ScenergiX Overview • Introduction • Preparations • ScenergiX activation • ScenergiX pattern • ScenergiX overlap zone (horizontal ScenergiX) • ScenergiX overlap zone (vertical ScenergiX) • ScenergiX size adjustment (White level) •...
Page 131: Preparations
12. Alignment menu Adjustable overlapping area Light output per image 100% image 1 image 2 Total composite light output 100% image 1 image 2 Image 12-36 ScenergiX Basic Principle 12.11.2 Preparations ScenergiX Preparations To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors: •...
Page 132: Scenergix Pattern
12. Alignment menu 12.11.4 ScenergiX pattern What can be done? To make the ScenergiX adjustment more easy, an internal pattern can be displayed. How to display or remove the pattern? 1. Use the ▲ or ▼ key to select Show pattern and press ENTER. The internal ScenergiX pattern is displayed.
Page 133 12. Alignment menu Overlap : number of pixels that overlap Horizontal resolution of 1 projector Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap. Horizontal Resolution source : number of active pixels of the source. How to set for the ﬁrst projector 1.
Page 134: Scenergix Overlap Zone (Vertical Scenergix)
12. Alignment menu Image 12-52 Image 12-51 12.11.6 ScenergiX overlap zone (vertical ScenergiX) Deﬁnitions Image 12-53 Scenergix overlap zone vertical Overlap : number of pixels that overlap Vertical resolution of 1 projector Total vertical screen resolution : [(Vertical resolution of 1 projector) x 2] minus (overlap) Vertical Resolution source : number of active lines of the source How to set for the ﬁrst projector 1.
Page 135: Scenergix Size Adjustment (White Level)
12. Alignment menu Image 12-57 How to set for the second projector 1. Go to Layout → Main window → Size 2. Enter the value for the Width as follow: Total Vertical screen resolution / 2 - 0.5 x overlap zone. 3.
Page 136 12. Alignment menu 5. Use the ▲ or ▼ key to select one of the four size adjustments and press ENTER. (image 12-63, image 12-64, image 12-65, image 12-66) A pattern with the different areas is displayed. (image 12-67) 6. Use the cursor keys to move the border of the overlap area to the desired position. Set ﬁrst the width for the ﬁrst projector and repeat for the second one.
Page 137: Adjusting The Black Level Of The Images
12. Alignment menu Image 12-68 Width set up for projector 1 Image 12-69 Width set up for projector 2 12.11.8 Adjusting the black level of the images Why black level adjustment For dark images, the overlap zone will be brighter then the rest of the images. Typically for DLP projectors, next to the overlap zone, a brighter area is recognized.
Page 138 12. Alignment menu Image 12-70 DLP Leakage area set up After the area is set, use TEXT key to remove the area border lines when adjusting the black level. How to set the leakage area width 1. Press MENU to activate the menus. 2.
Page 139: How To Adjust
12. Alignment menu Image 12-74 Image 12-75 DLP leakage area Overlap area DLP Leakage area How to adjust 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Alignment and press ENTER. 3. Use the ▲ or ▼ key to select ScenergiX and press ENTER. 4.
Page 140 12. Alignment menu Image 12-78 Image 12-76 Image 12-77 Image 2 Image 1 Image 12-79 Image 12-80 Black level adjustment Use the Reset function to bring all ScenergiX settings back to zero. R59770021 CLM R10+ 11/10/2010...
Page 141: Projector Control
13. Projector control 13. PROJECTOR CONTROL About this chapter This chapter explains the setup of the control part of the software such as projector address and all types of communication with the external world. Overview • Overview ﬂow • Projector address •...
Page 142: Projector Address
13. Projector control Level 1 Level 2 Level 3 Menu [Center] Bar scale [Bottom] Local LCD contrast Language English Français Deutsch Español Italiano 13.2 Projector address Overview • Individual projector address • Common address 13.2.1 Individual projector address About individual projector address Before a projector, and only this projector, can be controlled via a remote control, an individual address must be entered in the projector.
Page 143: Common Address
13. Projector control Image 13-4 13.2.2 Common address About common address A common address can be ’0’ or ’1’. Any command coming from a remote control programmed with that common address will be executed. How to change the common address? 1.
Page 144: Interface Standard
13. Projector control How to set up? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER. 3. Use the ▲ or ▼ key to select Serial communication and press ENTER. The serial communication menu opens.
Page 145: Rs422 Termination
13. Projector control 13.3.3 RS422 termination What can be done? When the interface standard is set to RS422, the last projector in a line should be RS422 terminated (ON position). All others in the line should be in the OFF position. How to set 1.
Page 146: Dhcp Setup
13. Projector control Default Gateway A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet. MAC address Media Access Control address.
Page 147: Subnet-Mask Set Up
13. Projector control 4. Use the ▲ or ▼ key to select IP-address and press ENTER to select. Note: An address contains 4 octets with a maximum value of 255. This must NOT be 0.0.0.0 for static IP-Address assignment. 5. Use the ▲ or ▼ key to select the desired digit and press ◄ or ► key to select the next digit in the address. enter the value with the digit keys on the remote control or local keypad.
Page 148: Default Gateway Set Up
13. Projector control Image 13-28 13.4.5 Default Gateway set up How to set up? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Projector control and press ENTER. 3. Use the ▲ or ▼ key to select Network and press ENTER. The Ethernet menu opens.
Page 149: Dmx
13. Projector control 4. Use the ▲ or ▼ key to select the desired IR receiver and press ENTER to toggle this receiver [on] or [off]. (image 13-33, image 13-34, image 13-35) Image 13-35 Image 13-34 Image 13-33 Activation key 1.
Page 150: Dmx Universe
13. Projector control enter a new value with the digit keys on the remote control or local keypad. 6. Use the ◄ or ► key to select the next digit and repeat step 5. 7. When the desired address is entered, press ENTER to store that address. (image 13-38, image 13-39, image 13-40, image 13-41) Image 13-40 Image 13-39 Image 13-38...
Page 151: Dmx Monitor
13. Projector control Image 13-45 13.6.3 DMX monitor What can be done? If a DMX device is connected, the settings per channel can be displayed in an on screen menu. How to start up the monitoring 1. Press MENU to activate the menus. 2.
Page 152: Dmx Mode
13. Projector control Image 13-50 When selecting DMX monitor and no DMX device is connected, the message “No DMX data, check connection <ENTER> to display channels” appears on the screen. When ENTER is pressed the same window appears as DMX Monitor but without values. About motor control (channel 6 and 7) If channel #6 is brought to 32 or more, this is the same as “motor”...
Page 153: Art-Net Activation
13. Projector control 3. Use the ▲ or ▼ key to select DMX and press ENTER. 4. Use the ▲ or ▼ key to select DMX mode and press ENTER to toggle between [Basic] and [Full]. (image 13-51, image 13-52, image 13-53) Image 13-53 Image 13-52...
Page 154: Shortcut Keys
13. Projector control The function can be: • Auto align (only aligning of the preview window is executed). • Auto-image menu. This function opens a auto image menu where the user can make his choice between auto align, auto contrast/brightness and auto phase. How to conﬁgure the Auto button? 1.
Page 155: Menu Position
13. Projector control Image 13-63 13.8 Menu position What is possible? The on screen menu and the bar scale can be positioned on different places on the screen. Both can be positioned : • Center • • Bottom How to change the position? 1.
Page 156: Language Selection
13. Projector control Image 13-69 Image 13-68 Image 13-67 13.10 Language selection What can be done? The user can change the language of the on screen menus and the local display menus to one of the available languages. The following languages are available: •...
Page 157: Service Menu
14. Service menu 14. SERVICE MENU About this chapter This chapter refers to the Service menu in which the owner can ﬁnd valuable information when calling the Barco help desk. Overview • Overview ﬂow • Identiﬁcation • Diagnosis • Internal service patterns •...
Page 158 14. Service menu The following items will be displayed: • Type of projector • Projector address • Package • Conﬁguration • Baud rate • IP address • MAC address • Text • Serial number of projector: this number can be useful when calling for technical assistance. •...
Page 159: Diagnosis
14. Service menu 14.3 Diagnosis What can be seen? The diagnosis menu gives the possibility to get an overview of the working of the projector. 14.3.1 How to start up the diagnosis? Start up 1. Press MENU to activate the menus. 2.
Page 160: Voltages
14. Service menu Image 14-11 Use the ▲ or ▼ item in the menu to select the previous or next page with information. 14.3.3 Voltages How to display an overview? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens.
Page 161: I²C Diagnosis
14. Service menu 14.3.4 I²C diagnosis How to select? 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen is displayed.
Page 162: Fan Speeds Overview
14. Service menu Image 14-22 Image 14-21 Image 14-20 Image 14-23 Use the ▲ or ▼ item in the menu to select the previous or next page with information. 14.3.6 Fan speeds overview How to get an overview? 1. Press MENU to activate the menus. 2.
Page 163: Spi
14. Service menu Image 14-27 Use the ▲ or ▼ item in the menu to select the previous or next page with information. 14.3.7 SPI How to get an overview 1. Press MENU to activate the menus. 2. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens.
Page 164: Internal Service Patterns
14. Service menu 3. Use the ▲ or ▼ key to select Diagnosis and press ENTER. The diagnosis screen will be displayed. 4. Use the ▲ or ▼ key to select Error logging and press ENTER. The Error logging overview menu is displayed. For more explanation about the stored error message, see "Error codes", page 203.
Page 165: Save Custom Settings
14. Service menu The service window opens. 3. Use the ▲ or ▼ key to select Restore factory defaults and press ENTER. The factory defaults conﬁrmation window opens. 4. Use the ▲ or ▼ key to select the setting to exclude and press ENTER to toggle between [No] and [Yes]. Repeat this step if necessary for the other settings.
Page 166: Reﬁll Mode
14. Service menu The service window opens. 3. Use the ▲ or ▼ key to select Save custom settings and press ENTER. The custom settings are written to the internal backup device. A message menu “Save data ...” is displayed during the save operation.
Page 167: Usb Memory
14. Service menu 14.8 USB memory What is possible with an USB device? An USB device, FAT 16 formatted can be used, to save custom settings from the projector or to load custom settings to the projector. This function is very handy to clone projectors. The following settings can be transported via an USB device: •...
Page 168: Over Temperature Dmd Safety
14. Service menu Load custom settings 1. Connect a FAT 16 formatted USB device to the USB port. 2. Press MENU to activate the menus. 3. Use the ▲ or ▼ key to select Service and press ENTER. The service window opens. 4.
Page 169 14. Service menu Image 14-57 Image 14-56 Image 14-55 R59770021 CLM R10+ 11/10/2010...
Page 170 14. Service menu R59770021 CLM R10+ 11/10/2010...
Page 171: Maintenance
15. Maintenance 15. MAINTENANCE About this chapter This chapter contains detailed maintenance procedures like lens cleaning, etc. These procedures can easily be performed by the operator of the projector. Overview • Cleaning the lens • Cleaning the exterior of the projector •...
Page 172 15. Maintenance ARNING Switch off the projector and pull out the power cord before starting the check procedure ! How to check Remove : lamp door, see "Removal of the lamp door", page 182. front cover, see "Removal of the front cover", page 181. back cover, see "Removal of the back cover", page 183.
Page 173: Servicing
This chapter contains general servicing procedures like lamp replacement, input unit replacement etc. Note that some of these procedures may only be performed by qualiﬁed technical service personnel. These procedure are marked with a warning. Extra service information Extra service information for qualiﬁed service technicians can be found on Barco’s Partnerzone (URL:www.partner- zone.events.barco.com). Registration is necessary.
Page 174: Replacement Of The Dust Filters On The Front Side
16. Servicing Image 16-1 Filter top replacement AUTION Never install a used HEPA ﬁlter. Always install a new HEPA ﬁlter. AUTION Never use the projector with a removed cover. Always reinstall the removed cover. 16.2 Replacement of the dust ﬁlters on the front side Necessary parts Two new HEPA dust ﬁlters.
Page 175: Lens Installation
16. Servicing Image 16-2 Front ﬁlter replacement AUTION Never install a used HEPA ﬁlter. Always install a new HEPA ﬁlter. AUTION Never use the projector with a removed cover. Always reinstall the removed cover. 16.3 Lens installation How to install the lens 1.
Page 176: Lens Removal
16. Servicing Image 16-3 Mounting the lens AUTION Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens before transporting the projector. Neglecting this can damage the Lens Holder and Prism. 16.4 Lens removal How to remove the lens 1.
Page 177: Removal Of A Lamp Unit
16. Servicing Image 16-5 Slide out lens 16.5 Removal of a lamp unit ARNING This procedure may only be performed by qualiﬁed technical service personnel. AUTION Never attempt to disassemble the lamp from its housing or to dispose of it. Due to its high internal pressure, the lamp may explode in either hot or cold states if improperly handled.
Page 178 16. Servicing Mercury Vapor Warnings: The lamp used in the projector contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors: • Ensure the projector is installed only in ventilated rooms. •...
Page 179: Mounting A New Lamp Unit
16. Servicing Image 16-9 Take out the lamp For recycling guidelines of the lamp, see "Recycling guidelines", page 8. 16.6 Mounting a new lamp unit About the lamp units All four lamp units are equal. A spare lamp can be inserted in any position without problems. See spare part list for the order numbers.
Page 180: Removal Of An Input Module
16. Servicing Image 16-10 Lamp insertion 16.7 Removal of an input module Necessary tools Phillips screw driver PH1 How to remove an input module 1. Switch off the projector and unplug the power cord at the projector side. 2. Release the two captive screws of the input module. (image 16-11) 3.
Page 181: Inserting An Input Module
16. Servicing AUTION Ensure that an unused slot is always covered with a dummy front plate. Immediately install after removing an input module a new input module or a dummy front cover. 16.8 Inserting an input module Necessary tools Phillips screw driver PH1 How to insert an input module 1.
Page 182 16. Servicing 6. Turn out the third lid using the back of the main lid. (image 16-14) 7. Top-up the reservoir with cooling liquid until the level is somewhat higher than the hole in the reservoir. (image 16-15) 8. Close the third lid again using the back of the main lid. Use a cloth to dab the residue of cooling liquid. Note: Make sure that no cooling liquid is spilled in the projector.
Page 183 16. Servicing Image 16-15 Top-up reservoir Image 16-16 Pressurize circuit R59770021 CLM R10+ 11/10/2010...
Page 184 16. Servicing R59770021 CLM R10+ 11/10/2010...
Page 185: Projector Covers, Removal And Installation
17. Projector covers, removal and installation 17. PROJECTOR COVERS, REMOVAL AND INSTALLATION Overview • Removal of the front cover • Removal of the lamp door • Removal of the back cover • Removal of the top cover • Removal of the side cover •...
Page 186: Removal Of The Lamp Door
17. Projector covers, removal and installation Image 17-2 Remove the front cover 17.2 Removal of the lamp door ARNING This procedure may only be performed by qualiﬁed technical service personnel. Necessary tools Flat screwdriver How to remove the lamp door 1.
Page 187: Removal Of The
17. Projector covers, removal and installation Image 17-4 Remove lamp door 17.3 Removal of the back cover Necessary tools Flat screwdriver How to remove the back cover 1. Release the 3 captive screws in the back cover. (image 17-5) 2. Pull off the back cover. (image 17-6) Image 17-5 Release captive screws R59770021 CLM R10+ 11/10/2010...
Page 188: Removal Of The Top Cover
17. Projector covers, removal and installation Image 17-6 Remove back cover 17.4 Removal of the top cover To remove the top cover, ﬁrst remove the front and back cover and the lamp door. Necessary tools Flat screwdriver How to remove the top cover 1.
Page 189: Installation Of The Side Cover
17. Projector covers, removal and installation Image 17-8 Loosen screws Image 17-9 Side cover removal 17.6 Installation of the side cover Necessary tools Allen wrench 3 mm How to install 1. Hook the side cover on the ﬁxation screws and pull the cover downwards until it matches with the bottom cover. (image 17-10) 2.
Page 190: Installation Of The Top Cover
17. Projector covers, removal and installation Image 17-11 Fixate side cover 17.7 Installation of the top cover How to install 1. Place the top cover on the projector and push on the front side and back side of the cover until it clicks into its locks (4 locks). (image 17-12) 2.
Page 191: Installation Of The
17. Projector covers, removal and installation Image 17-14 Secure back cover 17.9 Installation of the front cover Front cover can only be installed after that the side covers and top cover are installed. Necessary tools Flat screwdriver How to install the front cover 1.
Page 192: Installation Of The Lamp Door
17. Projector covers, removal and installation Image 17-15 Install front cover Image 17-16 Secure front cover 17.10 Installation of the lamp door Lamp door can only be installed when the top cover is installed. Necessary tools Flat screwdriver How to install the lamp door 1.
Page 193 17. Projector covers, removal and installation Image 17-17 Lamp door installation Image 17-18 Secure the lamp door R59770021 CLM R10+ 11/10/2010...
Page 194 17. Projector covers, removal and installation R59770021 CLM R10+ 11/10/2010...
Page 195: Dimensions
A. Dimensions A. DIMENSIONS Overview • Dimensions of the CLM R10+ A.1 Dimensions of the CLM R10+ Dimensions without carry handle 691.18 Image A-1 Dimensions R59770021 CLM R10+ 11/10/2010...
Page 196 A. Dimensions Dimensions with optional carry handle 145.5 97.5 Image A-2 R59770021 CLM R10+ 11/10/2010...
Page 197: Standard Source Files
B. Standard Source Files B. STANDARD SOURCE FILES B.1 Table overview Table overview The following standard image ﬁles are pre-programmed in the projector. Name Fvert FHor Fpix Ptot Pact Ltot Lact 640x350@85 85,079 37,860 31,500 640x400@85 85,079 37,860 31,500 640x480@60 59,940 31,668 25,175...
Page 198 B. Standard Source Files Name Fvert FHor Fpix Ptot Pact Ltot Lact 1400x1050RB@60 59,946 64,742 100,997 1560 1400 1080 1050 1600x1200@60 60,001 75,002 162,004 2160 1600 1250 1200 1600x1200@65 64,998 81,248 175,496 2160 1600 1250 1200 1600x1200@70 69,997 87,497 188,993 2160 1600 1250...
Page 199: Dmx Chart
C. DMX Chart C. DMX CHART Overview • CLM control channel mapping (Full mode) • CLM control channel mapping (Basic mode) C.1 CLM control channel mapping (Full mode) Overview Chan- Function Type Range Default Action Comments Intensity Xfade 0 - 255 0 - 100% Brightness Xfade 0 - 255 128...
Page 200: Clm Control Channel Mapping (Basic Mode)
C. DMX Chart Chan- Function Type Range Default Action Comments Motor Go >> 0 - 31 Stop 31 - 63 64 - 95 Future assignment Same as Stop 96 - Future assignment Same as Stop 128 - Future assignment Same as Stop 160 - Future assignment Same as Stop...
Page 201 C. DMX Chart Chan- Function Type Range Default Action Comments Function Select 0 - 7 No function 8 - 15 Activate Layout 1 (Main full If held for 2 Sec screen) 16 - 23 Activate Layout 2 (PiP top right) If held for 2 Sec 24 - 31 Activate Layout 3 (Split top - If held for 2 Sec...
Page 202 C. DMX Chart R59770021 CLM R10+ 11/10/2010...
Page 203: D.1 Speciﬁcations Clm R10
D. Specifications D. SPECIFICATIONS Overview • Speciﬁcations CLM R10+ • Speciﬁcations CLM 5 cable input (multi purpose) • Speciﬁcations CLM HDSDI – SDI input • Speciﬁcations CLM DVI input • Speciﬁcations CLM DVI HDCP input D.1 Speciﬁcations CLM R10+ Overview AC power 100 - 240 VAC (±10%)/50-60 Hz Aspect Ratio...
Page 204: Speciﬁcations Clm 5 Cable Input (Multi Purpose)
D. Specifications Orientation table/ceiling/side (portrait)/ vertical Power consumption 1,600 W Resolution 1,400 x 1,050 pixels (SXGA+) Safety Regulations Compliant with UL1950 and EN60950 ScenergiX Horizontal and vertical edge blending Weight 30kg (excluding lens and rigging frame) D.2 Speciﬁcations CLM 5 cable input (multi purpose) Front view 5 cable input 5-CABLE INPUT SYCN OK...
Page 205: Speciﬁcations Clm Hdsdi - Sdi Input
D. Specifications • Signal requirements: Component Video (BNC) R-Y : 0,7Vpp ±3dB 75 Ohm termination. Ys : 1Vpp ±3dB (0,7V Luma +0,3V Sync) 75 Ohm termination. B-Y : 0,7Vpp ±3dB 75 Ohm termination. RG(s)B R : 0,7Vpp ±3dB 75 Ohm termination. G(s) : 1Vpp ±3dB (0,7Vpp G + 0,3Vpp Sync) 75 Ohm termination.
Page 206: Speciﬁcations Clm Dvi Input
D. Specifications D.4 Speciﬁcations CLM DVI input Input front view DVI input Sync OK Image D-3 Speciﬁcations • DVI type: DVI-I (DVI-Integrated), but the analog signals are not supported. Single-link conﬁguration. • Single link dvi for pixelclocks up to 165MHz •...
Page 207: Troubleshooting
E. Troubleshooting E. TROUBLESHOOTING Error codes Overview When the error code is preceded by a ’-’ sign, then the error means a real error for the projector. When the error code is preceded by a ’+’ sign, then the error code means a warning. The projector does not fail yet, but take care for the warning and try to resolve the problem.
Page 208 E. Troubleshooting Error Description Error Warning Action Caused by code 4198 FPGA PMP init failed 6099 Board ID unkown version 6098 Board ID invalid string 7999 DMD temp low Low temperature on DMD turning on the lamp(s) will heat up the DMD 7998 DMD temp high...
Page 209 E. Troubleshooting Error Description Error Warning Action Caused by code 7908 Fan inlet A low Fan is running too slow or not at all If problem persists, call a qualiﬁed service engineer 7906 Fan inlet B low Fan is running too slow or not at all If problem persists, call a qualiﬁed service engineer 7904...
Page 210 E. Troubleshooting Error Description Error Warning Action Caused by code 7862 Lamp 1 run time shtdwn exceeded 7861 Lamp 2 run Run time of lamp 2 will be exceeded Replace the lamp with a new one. time msg Call a qualiﬁed service engineer exceeded 7860 Lamp 2 run...
Page 211 E. Troubleshooting Error Description Error Warning Action Caused by code 9399 Error image 9398 Maximum Reaching the maximum allowed Delete some unnecessary ﬁles image ﬁles number of ﬁles reached 10499 Error input 10498 Unsupported Module with obsolete ﬁrmware Call a qualiﬁed service engineer module 10497 Init DVI input...
Page 212 E. Troubleshooting R59770021 CLM R10+ 11/10/2010...
Page 213: Mounting Optional Carry Handle
F. Mounting optional Carry handle F. MOUNTING OPTIONAL CARRY HANDLE About this chapter This chapter describes the procedures to mount the optional carry handle to CLM projector. When this optional carry handle is mounted, the projector can be suspended with the rigging clamps and stacking of projector is possible. Overview •...
Page 214: Preparing The New Carry Handle
F. Mounting optional Carry handle Image F-2 Mounting the stacking points Image F-3 Stacking points mounted Preparing the new carry handle What has to be done? The back stacking point must be removed before the carry handle can be mounted on the CLM projector. The ﬁxation hole for the ﬁxation bolt of the carry handle is covered by the stacking point construction.
Page 215: Preparing The Projector
F. Mounting optional Carry handle Image F-4 Remove stacking point construction Preparing the projector AUTION Before turning the projector upside down, be sure the stacking points on the top cover are mounted. What has to be done? Before the carry handle can be mounted, the projector feet must be removed and an extra support point must be added. Necessary tools •...
Page 216: Mounting The Carry Handle
F. Mounting optional Carry handle Image F-5 Image F-6 Mounting the carry handle Necessary tools • 8 mm Allen wrench. • 4 mm Allen wrench. • 2,5 mm Allen wrench. Necessary parts • One spacer rotation ring. • One ﬂat spacer. •...
Page 217 F. Mounting optional Carry handle Image F-7 Image F-8 R59770021 CLM R10+ 11/10/2010...
Page 218 F. Mounting optional Carry handle R59770021 CLM R10+ 11/10/2010...
Page 219: Order Info
G. Order info G. ORDER INFO G.1 Spare part order info Order info: Order info Description R9854430 5 cable input module R9854450 HDSDI - SDI input module R9854460 DVI input module R848607 Cover plate for unused input slot R98610206 CLM dust ﬁlter kit, 6 pack R986102012 CLM dust ﬁlter kit, 12 pack R9861030...
Page 220 G. Order info R59770021 CLM R10+ 11/10/2010...
Page 221: Glossary
Glossary GLOSSARY 2:2 pull-down The process of transferring 24-frames/sec ﬁlm format into video by repeating each frame (used for PAL DVD’s) as two video ﬁelds. ( AD ) 3:2 pull-down Method used to map the 24 fps of ﬁlm onto the 30 fps (60 ﬁelds) or 25 fps (50 ﬁelds), so that one ﬁlm frame occupies three video ﬁelds, the next two, etc.
Page 222 Glossary MAC address Media Access Control address. Unique hardware number, used in combination with the IP-address to connect to the network (LAN or WAN). PiP stands for "Picture in Picture" and allows to display multiple windows containing each of them an image. The windows may be of the video or data type.
Page 223: Index
Index INDEX Cleaning Exterior Address Color saturation Program Color space Color standard Adjustment 52–54 Color temperature 79–80 Quick set up 52–54 Custom values Lens Predeﬁned values Lens functions Communication 43–44 Lens key Ethernet IR communication Adjustment mode 59–61 RS232 About RS422 LCD display menus USB port...
Page 224 Index File services Tint Manual load ﬁle Overview ﬂow Film mode detection Save custom settings Front cover 181, 187 Source timings Installation Start up Removal Timings 87–88 Front projection Advanced settings Image ﬁle services Image ﬁles standard Image services 92–97 Gamma Copy ﬁle General...
Page 225 Index Lamp mode Overview Native resolution Power Navigation Power mode Adjustment mode Run time overview Network 141–144 Status overview DHCP Lamp door 182, 188 Gateway Installation Introduction Removal IP-address Lamp identiﬁcation Subnet-mask Lamp mode No signal 69–70 Lamp power mode Background color Lamp run time overview Shutdown...
Page 226 Index Network 141–144 Battery explosion 7, 20 DHCP Cooling liquid circuit Gateway Electrical shock Introduction Fire hazard IP-address Flight cases Subnet-mask General Projector address 138–139 Instructions Address Mercury vapor warnings Common address Personal injury Serial communication 139–141 Projector damage Baud rate setup Replacement parts Interface standard Servicing...
Page 227 Index Source timings Top cover 184, 186 Speciﬁcations 199–202 Installation 5 cable input Remove CLM R10+ Troubleshooting DVI HDCP Error codes DVI input HDSDI–SDI input Diagnosis Ultraviolet radiation Stacking 33, 35 Unpacking Align projectors USB memory Projectors USB port Stacking points UV radiation Mounting Start up...
Page 228 Index R59770021 CLM R10+ 11/10/2010...
Page 229 Revision Sheet Barco nv Events/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11, Fax: +32 56.36.88.24 E-mail: service.mne@barco.com, Web: www.barco.com From: Date: Please correct the following points in this documentation (R59770021/11): page wrong correct R59770021 CLM R10+ 11/10/2010...

This manual is also suitable for:

Clm r10+ r90501005 Clm r10+ r9050100 Clm r10+

Barco CLM R10+ R90501001 User Manual

1 Safety

2 General

3 Physical Installation

4 Stacking CLM Projectors

5 Connections

6 Getting Started

7 Start up of the Adjustment Mode

8 Input Menu

9 Image Menu

10 Layout Menu

11 Lamp Menu

12 Alignment Menu

13 Projector Control

14 Service Menu

15 Maintenance

16 Servicing

17 Projector Covers, Removal and Installation

Dimensions

Standard Source Files

DMX Chart

Specifications

Troubleshooting

Mounting Optional Carry Handle

Order Info

Glossary

Index

Quick Links

Users manual

Need help?

Questions and answers

Related Manuals for Barco CLM R10+ R90501001

Summary of Contents for Barco CLM R10+ R90501001