Cisco ASR1002 - ASR 1002 Router Software Configuration Manual page 101

Software Upgrade Process
Command or Action
Step 12
issu loadversion rp
URL-to-active-file-system
version
spa}* *.pkg slot
issu commitversion
Repeat this step for each SIP installed in the
router before moving onto the next step.
Example:
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.
122-33.XNB1*.pkg slot 0 force
Router# issu commitversion
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.
122-33.XNB1*.pkg slot 1 force
Router# issu commitversion
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-{sipbase,sipspa}*02.02.01.
122-33.XNB1*.pkg slot 2 force
Router# issu commitversion
Step 13
issu loadversion rp
URL-to-active-file-system
standby-
pkg slot
issu commitversion
issu loadversion rp
URL-to-active-file-system
active-
pkg slot
issu commitversion
Example:
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*.
pkg slot 1
Router# issu commitversion
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-esp*02.02.01.122-33.XNB1*.
pkg slot 0
Router# issu commitversion
Step 14
issu loadversion rp
URL-to-active-file-system
force
Example:
Router# issu loadversion rp 0 file
bootflash:asr1000rp1-rp*02.02.01.122-33.XNB1*.p
kg force
active-RP
Step 15
show version
active-RP
show version
Example:
Router# show version r0 provisioned
Router# show version r0 installed
active-RP
file
:asr1000rp1-{sipbase,sip
SIP-slot-number
force
active-RP
file
:asr1000rp1-esp*
-slot
ESP
active-RP
file
:asr1000rp1-esp*
-slot
ESP
active-RP
file
version
:asr1000rp*
provisioned
installed
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Purpose
Upgrade the SIP and SPA subpackages for each SIP on the
router.
Note This step must be completed one SIP at a time, and
repeated for each SIP installed on the router before
performing the next step.
Tip You can use the show ip interface brief command
to identify which slots contain SIPs and SPAs. The
interfaces with three numbers (in the form
SIP-number/SPA-number/interface-number)
identify the SIP and SPA locations in the router.
The pattern options used in this CLI (sipbase and
Note
sipspa) were introduced in Cisco IOS XE Release
2.1.2 and are not available in previous Cisco IOS
XE Releases.
See the
Release 2.1.2)" section on page 74
IOS XE Release 2.1.2 ISSU upgrade procedures.
Upgrade the ESP Base subpackage on the standby and the
version
*.
active ESPs.
After entering the issu loadversion rp command on the
active RP, the ESP switchover will occur automatically.
version
*.
Minimal traffic interruption will occur as a result of this
switchover.
Upgrade all of the subpackages on the active RP.
*.pkg
This step is required to ensure that all subpackages
Note
on the router were upgraded as part of this
procedure, and might upgrade some subpackages
that would otherwise be missed in the process.
(Optional) Confirm that the subpackages are provisioned
and installed.
ISSU Upgrade for Redundant Platforms
"ISSU Procedures (Prior to Cisco IOS XE
for pre-Cisco
19