Section 4: Module Enrollment; Enrolling Keypads And Modules; Deleting Modules; Confirming Modules - DSC PC4020 Installation Manual

S e c t i o n 4 : M o d u l e E n ro l l m e n t

4.1 Enrolling Keypads and Modules

Once the wiring of all keypads and modules is complete,
they must be enrolled on the system. Apply power to the
system by first connecting the battery, followed by the AC
transformer. All LCD keypads will display the software
version of the keypad.
NOTE: Make sure all power to the system is OFF when con-
necting modules.
NOTE: Record the location and number of each module for
future reference.
Enrolling the First Keypad to Partition 1
To enroll the first keypad, go to the keypad that is to be
assigned to Partition 1. Press any key on that keypad. The
keypad will beep and display the message '45XX Mod. #1'.
This keypad will automatically be assigned to Partition 1.
Once the first keypad has been enrolled, the rest of the sys-
tem keypads and modules can be enrolled through the
'Module Hardware' section of installer's programming.
Enrolling All Other Keypads and Modules
Ref # [0200] then scroll to desired module
Enter the following at the keypad you have just enrolled:
1. Enter installer's programming by pressing [*] [8]
[Installer's Code].
NOTE: The default installer's code is [5555].
2. Scroll to 'Module Hardware' and press the [*] key.
3. The message 'Enroll Module' will appear. Press [*].
4. Scroll through the different modules until the module
you wish to enroll is displayed. Press the [*] key.
LCD45XX Keypads
The keypad will display the message 'Press Any Key On
Desired Unit'. Go to the keypad to be enrolled and press
any key. Return to the original keypad. A message similar
to the following will be displayed to confirm enrollment
(e.g. 'LCD45XX Mod 02 Enrolled').
For keypads: next, you must select which partition the key- For keypads: For keypads: For keypads:
pad is to control. Use the arrow keys to scroll to the desired
partition and press the [*] key to select. If the enrolled key-
pad is slated for global operation, scroll to Option 00 'Glo-
bal' and press [*].
If you press the [#] key, the keypad will be assigned to Parti-
tion 1 by default.
For more information regarding partition and global key-
pads, see Section 6: 'Keypad Operation'.
Module Tampers
When enrolling PC4108A, PC4116, PC4204/PC4204CX,
PC4216, PC44XX, PC4702, PC4820, PC4850, PC4164 or
alternate communicator modules, the message 'Create
Tamper On Desired Unit' will be displayed. The tamper is
required for enrollment.
To create the required tamper, secure the tamper zone on
the module and then open it. It is this transition from secure
to violated which enrolls the module. After this is done, the
keypad will display the module number and will confirm
enrollment (e.g. 'PC4204/PC4204CX Mod 01 Enrolled').
Record the module number in the programming work-
sheets. Once the module is enrolled, re-secure the tamper.
Zone Expanders
NOTE: Enroll all zone expanders before assigning zones to
PC4820 and AML devices.
When enrolling zone expanders (PC4108A, PC4116 and
PC4164), the panel will display 'PC41XX Module'. It does not
ask what type of expander is being enrolled. Once the
tamper is created, the control panel will automatically indi-
cate the type of expander and will confirm enrollment (e.g.
'PC4116 Mod 01 Enrolled').
Zones 1 to 16 are located on the main control panel. Addi-
tional zones are added in sequence. For example, if two
PC4108A zone expanders are enrolled, the first one enrolled
will be assigned zones 17 to 24 and the second will be
assigned zones 25 to 32.
The system can have a maximum of 128 zones. To confirm
which zones are assigned to which expander, press any key
when the enrollment confirmation message is displayed.
NOTE: Be sure to record the zones assigned to each zone
expander module in the System Overview section of the
Programming Worksheets.
The PC4164 is a wireless receiver. When you enroll a
PC4164 module, you can enroll up to 64 wireless devices
on the system.
You can enroll up to eight PC4164 wireless receivers. This
will give you a greater range in which to install wireless
devices. It will also allow you to install backup wireless
receivers with overlapping ranges, to provide increased
security for the wireless zones on the system.
NOTE: The maximum number of wireless zones you can
enroll on the system is 64, even if you install more than one
PC4164 wireless receiver.
ESCORT4580, PC4701 and PC4936 Enrollment
When enrolling the ESCORT4580, the PC4701 or the PC4936,
the keypad will display the message 'Looking for PC4XXX
Module'. The panel will automatically scan the Combus for
the module. Once it is found, the panel will confirm enroll-
ment (e.g. 'ESCORT4580 Module Enrolled'). No tamper is
required.

4.2 Deleting Modules

Ref # [0201] then scroll to desired module
Sometimes, a module must be deleted from the system.
This could be when zone expanders are enrolled out of
sequence or if a module is defective.
To delete a module, enter the following at any enrolled key-
pad:
1. Enter installer's programming by pressing [*] [8]
[Installer's Code].
2. Enter reference number [0201] then press [*].
3. Scroll through the different modules until the module
you wish to enroll is displayed. Press [*] to select.
4. Scroll to the correct module type, then to the correct
module number. For example, to delete LCD45XX Mod-
ule 04, scroll to 'LCD45XX (04)'. Press the [*] key to
delete the module.
NOTE: When deleting and/or replacing zone expanders, all
remaining zone expanders should be re-enrolled. This will
ensure proper zone assignment and operation.

4.3 Confirming Modules

Ref # [0202] then scroll to desired module
In case module numbers were not recorded, you can verify
this information through the 'Confirm Module' menu in the
'Module Hardware' programming section in installer's pro-
gramming.
11